About this module
At Level 1 you learned to be safe and to keep a car healthy. At Level 2 you learn to find what is wrong and to fix it properly, and to prove it to the customer.
Who it is for. People who have finished Auto Mechanics Basics (Level 1), or who can show the same skills. National Proficiency II covers routine tasks and some varied tasks under limited supervision. Hazardous work needs trainees of 18 or over.
CTVET status. CTVET lists "Automotive Mechanic" at NP I and NP II; the page we read shows approval on 28 April 2020 and an expiry of 27 April 2025. The unit list was not found online, so this module is not that curriculum and does not certify you. Ask CTVET, NVTI or the regional Ghana TVET Service office for the current standard. The trade-test grades and fees were not verified.
Bridge from Level 1: what you already know
- Jack stands, chocks, exhaust, fuel, battery and hot-part safety; used oil in sealed containers
- The ten systems; owner's manual; torque wrench; fluid map
- Oil and filter change, air filter, lights, wipers, service record
- Tyre pressure, wheel change in a star pattern, brake look-and-report
- Battery care, jump start, multimeter voltage readings, cold-engine coolant checks
- The ask, look, listen, test, fix, check method; a first look at OBD codes
- Costing a job, WhatsApp Business, registration and permits
Level 1 did not teach brake repair, suspension and steering checks, tune-up work, instrument testing of the starting, charging and cooling systems, job cards and estimates in detail, or running a small workshop. This manual does. Motorbikes are in the Hub's Motorbike and Tricycle Servicing; car air-conditioning gas is not taught here (see Refrigeration and AC Basics).
How the module works
Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent. About 70% of the time is practical.
Unit 1 · Diagnose with a method
Parts are expensive and customers are not patient. A good diagnosis saves money, time and your name.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 1.1 Gather information | interviews the customer; checks history; finds the correct workshop information |
| 1.2 Verify the fault | repeats the fault safely and records the symptom |
| 1.3 Use a scan tool | reads and records codes, freeze-frame data and readiness; does not clear a code to hide a fault |
| 1.4 Narrow the cause | uses tests to confirm or rule out each idea before changing parts |
| 1.5 Record and report | writes a diagnosis in plain words |
Range. Petrol and diesel light vehicles; common faults. Evidence. Diagnosis records; observation.
Tools and items for this unit
Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Level 1 items are defined in the Level 1 appendix; the Level 2 appendix adds the new ones.
| Item | What it is and what it does | Type or size (typical) | Care or safety | Also called |
|---|---|---|---|---|
| OBD-II scan tool | A tool that reads trouble codes, freeze-frame data and (on better tools) live data from the car's computer. Types: code reader, Bluetooth dongle with a phone app, professional tool. | 16-pin diagnostic socket, usually under the dashboard on the driver's side | Read and record; do not clear a code to hide a fault. | code reader, scanner, diagnostic tool |
| Freeze-frame data | A snapshot of engine conditions (speed, temperature, load) saved when a code was set. | A screen on the scan tool | Write it down before clearing anything. | freeze frame snapshot |
| Workshop manual | The maker's repair book with test tables, specifications, torque values and wiring diagrams. | Paper or paid online service | It overrules this book. | service manual, repair manual |
| Torch and mirror | A bright light and an angled mirror to see behind parts. | LED torch; telescopic mirror | Never a naked flame near fuel. | flashlight, work lamp |
The OBD scan tool is labelled in Level 1 Unit 6 (parts table and safety protocol); use the same protocol here.
Ask a qualified expert. Fuel-system, brake, airbag and electrical faults can injure people. Test only what this unit shows. For anything else, ask a qualified mechanic or a GhIE-registered engineer, and a licensed electrician for any mains wiring. Never road test a vehicle with a brake or steering fault.
Test before you replace
A trouble code points to a system or a circuit. It does not name the broken part. A five-character code starts with a letter for the system (P is powertrain); P0 codes are generic and mean the same on most makes. Clearing a code does not fix the fault. Read the code, then confirm with a test.
The method in detail
- Verify the complaint. Ride or drive with the customer if safe. Note when the fault happens: cold or hot, speed, load, braking, turning.
- Check the basics. Fuel, oil and coolant levels, battery voltage, loose connectors, air filter, fluid leaks.
- Read the codes and note the freeze-frame data (the conditions when the code was set).
- Find the workshop information: the manual's test table, wiring diagram and specifications. Do not guess values.
- List ideas in order of how likely and how cheap to test.
- Test the cheapest likely idea first. Record the result.
- Repair, then recheck: repeat the original conditions and rescan.
- Explain the cause and the repair to the customer in plain words.
Part swapping is a trap. Swapping parts at the customer's cost is a common cause of anger and lost trade. If you are not sure, say so, and offer a paid diagnosis first. Write what you tested and what you saw.
Reading a simple trouble tree
| Complaint | First tests |
|---|---|
| Engine misfire at idle | Codes; plug condition; coil or lead; air leaks; compression if needed (Unit 4) |
| Hard starting when hot | Battery voltage; starter draw; fuel pressure (qualified supervision); codes |
| Overheating | Coolant level; leaks; fan; thermostat; pressure test (Unit 5) |
| Car pulls to one side | Tyre pressure; brake drag; wheel play (Unit 2 and 3) |
| Charging light on | Belt; battery voltage; alternator output (Unit 5) |
Writing the diagnosis
Use four lines: Complaint (what the customer said); Findings (what you saw and measured, with numbers); Cause (what you believe and why); Advice (what to repair, parts and cost, and what can wait).
Which test first?
(1) A car cranks well but will not start, and the fuel gauge is on empty. (2) A car's battery warning light is on and the headlights are dim at idle. (3) A car squeals when braking only on wet mornings. For each, say the cheapest sensible first test.
Diagnosis drill
- The instructor sets a fault on a training car without telling you.
- Interview the owner (the instructor). Write the complaint.
- Check basics, scan for codes, and record freeze-frame data.
- List three ideas; test the cheapest first. Write the numbers.
- State the cause, fix it if within scope, and recheck.
- Write the four-line diagnosis and read it aloud to the "customer".
Last fault
Think of the last time a car you know had a problem. Write the complaint, what you think the cause was and one test that would have proved it.
Check yourself: Unit 1
- What does a trouble code give you: the broken part or an area?
- What is freeze-frame data?
- Name the four lines of a diagnosis.
Unit 2 · Brakes in depth
Brakes are not a place for experiments. Work clean, work to the manual, and have a qualified mechanic check it.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 2.1 Explain the brake system | names the pedal, booster, master cylinder, lines, calipers, drums and discs |
| 2.2 Inspect pads, discs and drums | measures and decides under supervision |
| 2.3 Replace pads in sets | works one axle at a time, cleans, lubricates and torques to the manual |
| 2.4 Replace or top up fluid and bleed | follows the bleed order and keeps the reservoir full |
| 2.5 Road test safely | tests in a safe place after a qualified check |
Range. Hydraulic disc and drum brakes on light vehicles. Under supervision. Evidence. Observation; inspection report; qualified mechanic's check.
Tools and items for this unit
Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Level 1 items are defined in the Level 1 appendix; the Level 2 appendix adds the new ones.
| Item | What it is and what it does | Type or size (typical) | Care or safety | Also called |
|---|---|---|---|---|
| Brake caliper | The clamp that holds the pads either side of the disc. Hydraulic pistons push the pads onto the disc. | Single or multi-piston; floating or fixed | Hang it on a hook; never by the hose. | no other common name found |
| Brake pad and shim and clip | The pad is friction material on a steel backing. Shims and clips quieten and hold it. | Match the car by part number | Replace both pads on an axle. | brake lining |
| Brake disc (rotor) | The steel disc that turns with the wheel. The minimum thickness is usually stamped on it. | Solid or ventilated | Measure with a micrometer. | brake rotor |
| Brake drum, shoe, wheel cylinder and self-adjuster | In a drum brake the shoes push outward on the drum. The wheel cylinder is the small hydraulic piston that pushes the shoes. The self-adjuster takes up wear. | Rear axle on many small cars | Take a photo before dismantling; replace springs as a set. | no other common name found |
| Handbrake (parking brake) cable | A steel cable that applies the rear brakes by hand lever. | Cable and adjuster | Test after every brake job. | parking brake, hand brake |
| Brake bleeding kit and bleed nipple | The bleed nipple is the small valve on the caliper or cylinder. A kit has a clear hose and bottle, or a one-way valve, or a pressure bleeder, to push air out with fluid. | Hand pump, one-person check-valve and pressure types | Never let the reservoir run dry. | brake bleeder |
| Flare-nut spanner (line spanner) | A spanner with a partly open ring that grips a brake-pipe nut without rounding it. | Common sizes 10, 11 and 12 mm (typical) | Use for brake pipes only. | wrench, open-end and ring spanner; line wrench, tubing wrench |
| Piston tool (caliper wind-back tool) | Tool that pushes or winds the caliper piston back to fit new pads. | Cube or wind-back type | Watch the reservoir level. | caliper wind-back tool |
| Micrometer | A precise screw gauge to measure thickness, such as a disc. Read the barrel and thimble scale; zero it first. | Outside type, 0 to 25 mm range, 0.01 mm reading (typical) | Keep it clean; do not over-tighten. | mic, screw gauge |
| Brake cleaner and brake grease | Brake cleaner is a spray solvent. Brake grease is heat-proof grease for slides. | Aerosol can; small tube | Ventilate; flammable; keep grease off pads and discs. | no other common name found |
| Mask for dust | A mask that stops brake dust and fumes being breathed in. | Dust or respirator type; ask a safety professional | Wet-wipe dust instead of blowing it. | dust mask, respirator |
Parts and safety: Drum brake
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Drum | Turns with the wheel; the shoes press inside | Do not touch hot; check for scoring |
| 2 | Brake shoe (leading) | Friction lining that pushes out onto the drum | Replace as an axle set |
| 3 | Brake shoe (trailing) | The second shoe | Keep lining free of oil and grease |
| 4 | Wheel cylinder | Hydraulic piston that pushes the shoes out | Leaks: refer |
| 5 | Self-adjuster | Takes up wear | Photograph before dismantling |
| 6 | Return springs | Pull the shoes back | Replace springs as a set |
| 7 | Backing plate and handbrake lever | Holds the parts; the cable applies the handbrake | Test the handbrake after the job |
Safety protocol: Drum brake
Before. Supervisor present. Support on stands, remove the wheel. Wear glasses, gloves and a dust mask. Photograph the parts first.
While you work. Work one side at a time. Never blow dust; wet-wipe it. Keep grease off linings. Never let the reservoir run dry while bleeding.
After. Refit, adjust, torque wheel nuts in a star pattern, test the pedal and handbrake. A qualified mechanic checks the job and the first road test.
Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.
Parts and safety: Outside micrometer
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Frame | Holds the anvil and spindle | Do not drop or hold with a hot hand for long |
| 2 | Anvil | Fixed measuring face | Keep faces clean |
| 3 | Sleeve (barrel scale) | Shows whole and half millimetres | Read it first |
| 4 | Thimble | Turns to give hundredths | Read with eyes level |
| 5 | Ratchet | Gives constant measuring force | Use it; do not over-tighten |
| 6 | Lock (spindle) | Locks a reading | Release before zero check |
Safety protocol: Outside micrometer
Before. Wipe the faces clean. Check zero by closing the faces. Wear no gloves that stop you feeling.
While you work. Close with the ratchet only. Read with the part still and at eye level. Do not force. Do not measure moving parts.
After. Open the faces slightly, wipe, oil lightly, store in its case. Report a micrometer that is dropped or will not zero.
Emergency. For a cut, clean the wound; for serious injury call 112.
Safety protocol: brake pad replacement and bleeding (supervised)
Before. Qualified mechanic supervising. Car on stands. Glasses, gloves, dust mask. The manual open at the right page.
While you work. One side at a time. Never let the caliper hang on the hose. Never blow dust. Keep the reservoir full. Close the nipple before the foot lifts.
After. Torque the wheel nuts, pedal firm, collect used brake fluid in a sealed labelled container, qualified mechanic checks and road-tests.
Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.
Ask a qualified expert. Brakes decide whether people live. Do this work only under a qualified mechanic, with the manual open, and have the qualified mechanic or a GhIE-registered engineer check the finished job and the first road test. Do not touch anti-lock brake (ABS) modules, airbags or brake lines you cannot identify. Never work under a vehicle that is not on jack stands.
How the brakes work
Pressure from your foot goes to the master cylinder, which pushes brake fluid through steel lines and hoses to each wheel. At a disc brake, a caliper squeezes two pads on a spinning disc. At a drum brake, shoes push outwards against the inside of a drum. Fluid cannot be squeezed, so it moves the pistons; air can be squeezed, so air in the lines gives a soft pedal. A booster (vacuum or hydraulic) makes the pedal easier.
Brake fluid
- DOT 3 and DOT 4 brake fluids are glycol based and take in moisture, which lowers their boiling point. Many sources suggest a change about every two years, but the manual rules; humid climates may need sooner.
- Use only the fluid grade printed on the cap or in the manual. Do not mix types you are unsure of.
- Keep the container closed and clean; never reuse old fluid.
Inspect before you decide
- Park, secure, lift and support the car (Unit 1 of Level 1). Remove the wheel.
- Look at the pad: how thick is the friction material? Many sources say plan replacement near 3 mm, but limits vary by vehicle, so use the manual.
- Look at the disc: deep grooves, a lip at the edge, cracks, blue marks from heat. The minimum disc thickness is usually marked on the disc or in the manual; measure it with a micrometer.
- Look at the caliper and hoses: fluid leaks, cracked hoses, seized sliders.
- Grinding means metal on metal and may mean the disc is ruined too.
- Report in writing to your supervisor before you start.
Replace pads on one axle, step by step
Disc pad replacement (supervised)
- Check the manual for the pad type, torque values and any special steps for the parking brake or electronic callipers.
- Lift, support on stands and remove both wheels on the same axle. Work one side at a time so the other side shows you how it goes back together.
- Remove the caliper bolts. Hang the caliper on a hook or wire. Never let it hang by its brake hose.
- Take out the old pads and note how the clips and shims sit. Take a photo.
- Clean the caliper bracket and sliders with brake cleaner. Never blow brake dust with your mouth or an air line; wear a mask and wet-wipe the dust.
- Push the caliper piston back slowly with the correct tool. Watch the fluid level in the reservoir so it does not overflow.
- Smear brake grease only on the places the manual names (slides and pad backs); keep grease off pad faces and discs.
- Fit new pads and shims, refit the caliper and tighten the bolts to the torque in the manual.
- Repeat on the other side of the axle. Replace pads in axle sets.
- Refit wheels in a star pattern to the manual's torque.
- Before the car moves, press the pedal several times until it is firm. Check the fluid level.
- Hand over to the qualified mechanic for inspection and the first road test.
Drum brakes in a few lines
Look for worn shoes, scored drums, leaking wheel cylinders and a loose self-adjuster. Drum brakes are fiddly: take a photo before you start and replace springs and clips as a set. At this level, drum work is supervised and checked.
Bleeding the brakes
A soft pedal after a brake job or a fluid change means air in the system. Common practice is to bleed from the wheel farthest from the master cylinder to the nearest, but the order varies by car, so use the manual's order. Never let the reservoir run dry or you will pull air in again.
Bleed brakes (supervised, two people)
- Check the manual for the bleed order and fluid. Fill the reservoir to MAX.
- Fit a clear hose on the bleed nipple, with the end in a clean jar with a little fluid.
- Your helper presses the pedal and holds it. Open the nipple a little; fluid and air flow out; close the nipple before the helper lifts their foot.
- Repeat until the fluid is clear and free of bubbles. Top up the reservoir after every few strokes.
- Move to the next wheel in the manual's order.
- Finish with a firm pedal; the level at MAX. Collect used brake fluid in a sealed labelled container. Do not pour it away.
- Have the qualified mechanic check before the road test.
Road test
Start in a safe, quiet, open place. Press the pedal at walking pace: it must be firm and the car must stop straight. Test the handbrake. Increase speed only when low-speed tests are good. If anything is wrong, stop and fix it.
Brake figures
A brake disc is marked minimum 22.0 mm (example). Measurements on a car: 22.6 mm, 21.8 mm. (1) Which measurements are acceptable? (2) What should you do? (3) A pad was 9 mm new, is now 3 mm. How much has worn? What percent of its thickness is left?
Brake record
Write a one-page brake inspection report for a car you can look at (wheel on only if the car is safely supported by your instructor). Note pad, disc and fluid. Leave the repair to the instructor.
Check yourself: Unit 2
- Why must pads be replaced in axle sets?
- Why is a soft pedal after brake work a warning?
- Why must the caliper never hang from the hose?
Unit 3 · Suspension, steering and wheels
The car should go where you point it and sit level on the road. Look for play, noise and uneven wear.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 3.1 Explain the parts | names springs, shocks, control arms, ball joints, tie rods, bushes and bearings |
| 3.2 Inspect for play and wear | uses safe checks to find worn parts |
| 3.3 Read tyre wear | links wear patterns to causes |
| 3.4 Do simple jobs | replaces a shock or a track rod end under supervision |
| 3.5 Know alignment | explains toe, camber and caster and when to refer |
Range. Light vehicles. Inspect and under supervision replace simple parts. Springs and steering racks are not taught. Evidence. Inspection records; observation.
Tools and items for this unit
Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Level 1 items are defined in the Level 1 appendix; the Level 2 appendix adds the new ones.
| Item | What it is and what it does | Type or size (typical) | Care or safety | Also called |
|---|---|---|---|---|
| Coil spring and shock absorber (damper) | The spring carries the car. The shock absorber controls the bounce. Together they are the suspension at each wheel. | Strut type combines both | Never use a spring compressor at this level. | damper |
| Control arm, ball joint and bush | The control arm links the wheel to the body. The ball joint is its swivel. The bush is a rubber cushion. | Front and rear | Look for torn boots and cracked rubber. | wishbone, A-arm; bushing |
| Tie rod end and steering rack | The tie rod end connects the steering to the wheel. The rack turns the wheels when you steer. | Left and right | Play is checked on stands. | track rod end |
| Wheel bearing | Steel balls or rollers in a ring that let the wheel spin freely. | Sealed unit or adjustable | Rumble that changes with speed points to it. | hub bearing |
| Anti-roll bar link | A small rod that joins the anti-roll bar to the suspension and reduces body lean. | Short rod with two ends | Clunk over bumps. | stabiliser link, sway bar link, drop link |
| Ball-joint separator and pullers | Tools that push apart a tapered joint or pull a part off a shaft without damage. | Fork or screw type | Use the right size; refer if unsure. | pickle fork, joint splitter |
| Dial gauge and vernier caliper | The dial gauge measures small movements such as runout. The vernier caliper measures lengths and diameters to about 0.02 mm. | Dial: 10 mm range; vernier: 150 mm | Keep clean; zero before use. | dial indicator; slide calliper |
| Wheel balancer and tyre changer | Workshop machines that spin a wheel to find imbalance and remove or fit tyres. | Workshop machines; not for beginners | Operate only when trained. | no other common name found |
| Straight edge, tape measure | A straight edge shows flatness; a tape measures distances. | 300 mm to 1 m | Use for ride height and simple checks. | straightedge |
Parts and safety: Front suspension and steering at one wheel
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Strut mount (top mount) | Fixes the top of the strut to the body | Worn mount: clunk or noise |
| 2 | Coil spring | Carries the car | Never use a spring compressor at this level |
| 3 | Shock absorber (damper) | Controls bounce | Replace in pairs on an axle |
| 4 | Control arm bush | Rubber cushion where the arm pivots | Cracked rubber: report |
| 5 | Ball joint | Swivel between arm and wheel hub | Play: report; refer |
| 6 | Wheel bearing and hub | Lets the wheel spin freely | Rumble changing with speed |
| 7 | Tie rod end | Connects steering to the wheel | Play shown by the 3 and 9 o'clock test |
| 8 | Anti-roll bar link | Reduces body lean | Clunk over bumps |
Safety protocol: Front suspension and steering at one wheel
Before. Check tyre pressures. Lift on rated stands, wheel off the ground. Wear glasses and gloves.
While you work. Do the rock and spin tests with the car stable. Keep fingers clear of the gap between parts. Never remove a loaded spring.
After. Lower the car, torque wheel nuts. Write the report. Alignment must be done after any steering or suspension part is replaced; a qualified mechanic checks the repair.
Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.
Ask a qualified expert. Suspension and steering failures cause crashes. Compressed coil springs can strike with deadly force: never use a spring compressor at this level. Ask a qualified mechanic or a GhIE-registered engineer to check and sign off any steering or suspension repair before the car is driven. Support the car on stands before any work.
The parts in plain words
Springs hold the car up; shock absorbers control the bounce; control arms and ball joints let the wheels move up and down and turn; tie rods connect the steering to the wheels; bushes are rubber cushions; wheel bearings let the wheel spin freely.
Inspect: look, bounce, shake
- Bounce test. Push down on each corner and release. The car should settle after one or two bounces. A badly worn shock keeps bouncing. A test drive gives a more accurate picture.
- Look. Oil wetness on a shock body, cracked rubber bushes, torn boots on ball joints or CV joints, bent parts.
- Wheel play (car on stands). Hold the wheel at 12 and 6 o'clock and rock it: play points to a ball joint or a bearing. Hold at 3 and 9 o'clock and rock: play points to a tie rod end. Spin the wheel: listen for a rumble (bearing).
- Check wheel bearings first, because play there can feel like a loose suspension part.
Loose tie rod ends upset the toe angle, and worn ball joints upset the camber and cause fast tyre wear and pulling.
Reading tyre wear
| Wear | Likely cause |
|---|---|
| Both edges worn | Under-inflation |
| Centre worn | Over-inflation |
| One edge worn | Alignment (toe or camber) or worn parts |
| Cupping or scalloping | Worn shocks or out-of-balance wheels |
| Flat spots | Hard braking, locked wheels |
Alignment in a few lines
Toe is how far the fronts of the wheels point in or out; camber is the tilt in or out at the top; caster is the forward or backward tilt of the steering axis. A pre-alignment inspection (tyre pressure, ride height, worn bushes and ball joints) must come before measuring angles, because worn parts make settings drift. Alignment needs a machine and a trained operator; refer to a workshop that has one. A hit on a kerb or a pothole can bend parts and shift camber or caster.
Suspension and steering inspection
- Check tyre pressures first.
- Bounce each corner and record how many times it moves.
- Lift the front on stands. Do the rock tests for ball joints, tie rods and wheel bearings. Record play (none, slight, big).
- Look at boots, bushes and shocks for tears or wetness.
- Inspect tyre wear. Match it to a cause in the table.
- Write a report with parts to repair, urgency and your advice.
- With the instructor, replace one simple part (a tie rod end or a shock) following the manual. Have the work checked, then note that alignment must be done afterwards.
Cost the repair
Example prices: two front shocks GH¢700 each, labour GH¢150 per shock, alignment GH¢120. (1) Total? (2) If you charge 20% on top of the total, what is the price? (3) If the customer buys only one shock, what is the risk?
Tyre wear walk
Look at the tyres on five cars. Write the wear pattern and the likely cause. Do not touch a vehicle without permission.
Check yourself: Unit 3
- What does cupped tyre wear point to?
- Why check wheel bearings before blaming ball joints?
- Why is a spring compressor not used at this level?
Unit 4 · Engine tune-up: air, fuel and ignition
An engine needs clean air, the right fuel, a good spark and good timing. Check each in turn.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 4.1 Explain the four-stroke cycle | names intake, compression, power and exhaust |
| 4.2 Service air and fuel filters | replaces filters following the manual |
| 4.3 Inspect and replace spark plugs | reads, gaps and torques plugs |
| 4.4 Check belts and timing belt interval | inspects, records and refers timing belt work |
| 4.5 Do a compression test | tests, records and interprets the results |
Range. Petrol engines; diesel notes where the steps apply. Evidence. Test records; observation.
Tools and items for this unit
Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Level 1 items are defined in the Level 1 appendix; the Level 2 appendix adds the new ones.
| Item | What it is and what it does | Type or size (typical) | Care or safety | Also called |
|---|---|---|---|---|
| Spark plug | A plug that makes the spark in a petrol cylinder. Heat range is how quickly it sheds heat; the gap is the space at the tip. | Thread and reach by engine | Never bend the centre electrode. | sparking plug |
| Spark plug socket and gap gauge | A deep socket with a rubber insert to hold the plug. The gap gauge (feeler blade or wire) checks the gap. | Common sizes 16 or 21 mm (typical) | Start the thread by hand. | sparking plug |
| Ignition coil and ignition lead | The coil makes the high voltage. A lead carries it to the plug. Coil-on-plug types sit on each plug. | Four-cylinder cars often have four coils | High voltage; do not touch with the engine running. | HT lead, plug wire |
| Feeler gauge | A set of thin steel blades of known thickness to measure small gaps. | 0.05 to 1 mm blades | Wipe clean; do not bend. | thickness gauge, feeler blade |
| Compression tester | A gauge with a hose or adapter that screws into the plug hole and reads cylinder pressure while the engine is cranked. | Screw-in or push-in type, gauge to about 300 psi | Disable fuel and ignition first. | compression gauge |
| Fuel pressure gauge | A gauge that reads fuel pressure on a test port. Fuel is under pressure and can spray. | Use only with a qualified mechanic | Release pressure as the manual says. | no other common name found |
| Timing belt, tensioner, idler and chain | The timing belt (or chain) keeps the valves and pistons in step. The tensioner and idler keep it tight and guided. | Inside a cover at the engine front | Replacement is not done without a qualified mechanic and a locking tool set. | cam belt |
| Throttle body, injector, PCV and EGR valve | The throttle body controls air. The injector sprays fuel. The PCV valve vents crankcase gas. The EGR valve feeds some exhaust gas back to cool combustion. | On the engine intake side | Look and report; replacement is for later levels. | fuel injector |
| Vacuum gauge | A gauge that reads engine vacuum; the needle pattern helps trace leaks and valve faults. | Hand-held with hose | Use as the manual shows. | no other common name found |
Parts and safety: Spark plug and ignition coil
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Terminal | Connects the lead or coil | Do not touch with the engine running |
| 2 | Ceramic insulator with ribs | Insulates the high voltage | Cracked insulator: replace |
| 3 | Hex and shell | Where the socket fits | Use the right plug socket |
| 4 | Thread | Screws into the cylinder head | Start by hand; do not cross-thread |
| 5 | Centre electrode | The spark leaves from here | Do not bend |
| 6 | Ground electrode (gap) | Spark jumps the gap to it | Set the gap to the manual's figure |
| 7 | Ignition coil | Makes the high voltage | Do not touch while running |
| 8 | Coil connector | Low-voltage plug | Make sure it clicks on |
Safety protocol: Spark plug and ignition coil
Before. Engine off and cold. Label coils or leads. Clean around the plug. Wear glasses and gloves.
While you work. One plug at a time. Start the thread by hand. Torque to the manual. Never test spark on a running engine at this level.
After. Refit coils, check the clicks, start the engine and listen. Record each plug's condition.
Emergency. Electric shock: do not touch the person until the ignition is off; call 112 if unwell or unconscious. Fuel smell: no flames, ventilate.
Parts and safety: Compression tester
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Gauge | Reads cylinder pressure | Compare readings between cylinders |
| 2 | Needle | Holds the highest reading | Reset before each test |
| 3 | Hose | Carries pressure from the plug hole | Check for splits |
| 4 | Adapter (screw-in or push-in) | Seals in the spark plug hole | Do not cross-thread |
| 5 | Thread end | Screws into the cylinder head | Hand tight only |
| 6 | Release valve | Lets the pressure out after the test | Open after each test |
Safety protocol: Compression tester
Before. Engine warm then OFF. Disable fuel and ignition as the manual says so it cannot start. Wear glasses and gloves.
While you work. Remove all plugs. Crank for several turns with the throttle open. Record each cylinder. Keep hands and clothes away from belts.
After. Refit plugs, re-enable fuel and ignition, start and check leaks. Write the report.
Emergency. Fuel spray or fire: stop, isolate the battery if safe, use the extinguisher, call 112.
Ask a qualified expert. Petrol is highly flammable and fuel systems can be under pressure. Ignition systems carry high voltage that can give a painful or dangerous shock. Do not touch ignition leads with the engine running. For fuel-system pressure work, timing belt replacement or anything you are unsure of, ask a qualified mechanic or a GhIE-registered engineer; ask a licensed electrician about workshop wiring.
The four-stroke cycle
In a petrol engine each cylinder repeats four steps: intake (the piston goes down and draws air and fuel in), compression (the piston goes up and squeezes the mixture), power (the spark lights it and the piston is pushed down) and exhaust (the piston goes up and pushes the burnt gas out). Valves open and close at the right moments, controlled by the camshaft, which is driven by the timing belt or chain.
Air filter and fuel filter
- A dirty air filter chokes the engine. Replace it as the schedule says.
- A clogged fuel filter starves the engine. On many cars the fuel system stays under pressure after switching off; follow the manual's pressure-release steps or refer. Never open a fuel line near a spark or a hot manifold.
Spark plugs
- With the engine cold, label the leads or coils, and clean around each plug so dirt does not fall into the cylinder.
- Remove one plug at a time with the correct socket.
- Read the plug: a light tan or grey tip is normal; black soot means rich mixture; oily means oil getting in; white or blistered means running hot. Record each plug.
- Check the gap with a gauge to the manual's figure. Do not bend the centre electrode.
- Start the thread by hand to avoid crossing it. Tighten to the torque in the manual.
- Refit the lead or coil and make sure it clicks on.
Timing belt: know the limit
A timing belt (or chain) keeps the valves and pistons in step. Belts have a replacement interval; chains usually do not. In an interference engine a broken belt can let the pistons hit the valves and wreck the engine; follow the maker's schedule. Check the interval in the manual and record the last change. Changing a timing belt is not a Level 2 job on your own; do it only under a qualified mechanic and a locking tool set.
Compression test
A compression test shows the sealing of each cylinder. The lowest cylinder should not be more than about 15% below the highest, as a rule of thumb. If one is low, adding a little oil and retesting separates the causes: if the reading rises, think piston rings; if it stays low, think valves. Compare with the manual's specification before you decide.
Compression test (supervised)
- Warm the engine, then switch it off. Disable the fuel and ignition as the manual says, so the engine cannot start.
- Remove all plugs. Fit the compression tester to cylinder 1.
- Crank the engine for several turns with the throttle open. Note the highest reading.
- Record each cylinder. Work out the difference between the highest and lowest as a percentage.
- For any low cylinder, add about a teaspoon of oil, retest and record.
- Refit plugs and re-enable the fuel and ignition. Start and check for leaks.
- Write a report with your findings and advice.
Read the results
Four cylinders read 150, 148, 120, 149 psi (example). (1) Which cylinder is low? (2) By what percent is it below the highest? (3) After a little oil it reads 145 psi. What does that suggest?
Plug reading
Ask a mechanic to show you three used spark plugs. Describe them and what each tells you.
Check yourself: Unit 4
- Name the four strokes.
- Why can a broken timing belt wreck an interference engine?
- If a low cylinder rises after oil is added, what is likely?
Unit 5 · Starting, charging and cooling systems
Test, do not guess. A multimeter and a pressure tester will tell you where the problem is.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 5.1 Test the battery | reads resting voltage and checks load and cranking voltage |
| 5.2 Test the charging system | measures charging voltage at idle and with loads |
| 5.3 Find a battery drain | measures the parasitic drain safely |
| 5.4 Test the starter circuit | checks cranking and voltage drop |
| 5.5 Service the cooling system | pressure tests, replaces a thermostat and refills and bleeds |
Range. 12-volt systems; petrol and diesel light vehicles; cooling work on cold engines. Evidence. Test records; observation.
Tools and items for this unit
Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Level 1 items are defined in the Level 1 appendix; the Level 2 appendix adds the new ones.
| Item | What it is and what it does | Type or size (typical) | Care or safety | Also called |
|---|---|---|---|---|
| Battery load tester | A tool that loads the battery for a short time while it reads the voltage drop, showing the battery's health. | Carbon-pile or digital type | Follow the maker's steps; acid risk. | carbon pile tester |
| Hydrometer (battery) and refractometer (coolant) | The battery hydrometer reads acid strength in flooded cells. The refractometer reads coolant mix strength from a drop. | Hand-held | Wear glasses and gloves. | antifreeze; specific-gravity tester |
| Multimeter, amp range and fused 10 A socket | The 10 A socket measures current through the meter. It is fused, so a wrong connection blows the fuse. | DC amps, 10 A | Never open a lead with the meter set for volts. | DMM, volt-ohm meter, avometer; blade fuse |
| Clamp meter | A meter that measures current by clamping around a wire, without breaking it. | DC clamp types for car work | Use on one wire only. | tong tester, current clamp |
| Jumper lead and test light | A jumper lead is a short wire with clips. A test light glows to show voltage is present. | Test light with a probe | Use only low-voltage tests as shown; do not probe computer wires. | circuit tester, test lamp |
| Cooling system pressure tester | A hand pump with a gauge that pressurises the cooling system to find leaks. | Adapters for caps and filler necks | Engine cold only. | radiator pressure tester |
| Thermostat and thermostat housing | A temperature-sensitive valve; the housing holds it. | Rated by opening temperature | Use the right rating and a new seal. | no other common name found |
| Starter motor and relay | The starter is the electric motor that turns the engine. A relay is an electric switch that lets a small current switch a big one. | Starter on the gearbox bell | Keep hands clear. | starter motor, self-starter |
| Terminal puller and cleaning tools | A puller removes a stuck battery clamp. Cleaning tools are brushes. | Tools for lead terminals | Do not hammer the clamp. | no other common name found |
The battery and alternator are labelled in Level 1 Unit 5 and the multimeter in Level 1 Unit 2; use the same safety protocols here.
Ask a qualified expert. Batteries can burst and burn; coolant under pressure scalds. Work on 12-volt circuits only, with the battery's negative lead disconnected where the manual says. Ask a qualified mechanic, an auto electrician or a licensed electrician before any job beyond these tests. Do not work on hybrid or electric vehicles' orange high-voltage cables.
Battery and charging tests
| Test | Reading (rule of thumb) | Meaning |
|---|---|---|
| Resting voltage (engine off, rested an hour or more) | About 12.6 V | Charged |
| About 12.2 V | Half charged | Charge it |
| About 12.0 V or less | Discharged | Charge and test |
| Engine running at idle | About 13.8 to 14.4 V | Charging OK |
| Running, below about 13.5 V | Undercharging | Belt or alternator |
| Running, above about 15 V | Overcharging | Regulator fault |
Another source gives a wider running range of 13.5 to 14.8 V; treat all numbers as rules of thumb, and check the manual and battery type.
Load test. A battery tester puts a load on the battery for a few seconds. A weak battery drops fast. Follow the tester's instructions and record the result.
Alternator test, step by step
Charging test
- Check the belt: tight, not cracked.
- With the engine off, read battery voltage. Record it.
- Start the engine. At idle, read the voltage across the battery terminals. Record it.
- Switch on the headlights, blower and rear screen heater. Read again.
- Raise the revs to about 2,000 rpm for a short time and read again.
- Compare with the table and the manual. Write the readings and your conclusion.
- If charging is low, check the connections and the wiring before you condemn the alternator.
Battery drain (parasitic draw)
If the battery goes flat after standing, something is drawing current. With the ignition off, doors shut and the car left to "sleep" for the time the manual says, put a multimeter on the amp range in series with the negative lead (use the fused 10 A input). Remove fuses one at a time to find the circuit that drops the draw. Safe steps: do not start the engine or open a door with the meter in the lead, or you may blow its fuse. Ask a supervisor to check the set-up before you open a lead.
Starter circuit
A slow or clicking start can be a weak battery, a poor connection or a worn starter. Check the battery voltage while cranking: a healthy battery usually stays at about 10 V or more as a rule of thumb (not verified; check the manual). Clean and tighten the battery terminals, the earth strap and the starter connections. If the voltage is fine and the starter still does not spin, refer to an auto electrician.
Cooling system service
- Pressure test (engine cold): fit the tester to the radiator or reservoir cap neck and pump to the cap's rating. The pressure should hold; a drop shows a leak. Never test a hot engine.
- Thermostat: a thermostat that sticks closed causes overheating; one stuck open stops the engine warming. Replace with the correct temperature rating and a new seal.
- Coolant: use the type in the manual. Antifreeze is poisonous, and animals like its sweet taste. Collect drained coolant in a sealed, labelled container and ask the EPA how to dispose of it (not verified).
- Bleed the air so no air pocket stays: follow the manual's bleed steps, then run the engine until the fan starts and top up when cool.
Thermostat and cooling check (supervised)
- With the engine cold, pressure test the system and record how long it holds.
- Drain part of the coolant into a clean container.
- Remove the thermostat housing and the thermostat. Check it opens in hot water (a tea-pot test with a thermometer) if the manual gives a figure.
- Refit with a new gasket, same orientation, and tighten to the torque.
- Refill with the correct mixture and bleed the air as the manual says.
- Run the engine and watch the temperature gauge and for leaks. Top up when cool.
- Record the work and the used coolant container.
Voltage detective
Car A: 12.7 V rested, 14.2 V running. Car B: 12.0 V rested, 12.4 V running. Car C: 12.5 V rested, 15.4 V running. Say what each suggests and what to do.
Cooling inspection
Look at the cooling system of a car (engine cold, with permission). Write the coolant level, hoses and signs of leaks.
Check yourself: Unit 5
- What running voltage suggests normal charging?
- Why must a pressure test be done on a cold engine?
- In what way is the multimeter connected to measure a drain?
Unit 6 · Quality, estimates and customers
Customers return when they trust you. Trust comes from clear estimates, written approval, clean work and honest advice.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 6.1 Use job cards | writes the complaint, work, parts and mileage |
| 6.2 Give an estimate and get approval | explains costs and gets agreement before extra work |
| 6.3 Check quality | uses a final checklist and road test |
| 6.4 Handle waste and the law | stores waste safely; knows roadworthiness rules |
| 6.5 Care for customers | explains in plain words; keeps promises |
Range. Small garage or mobile service. Evidence. Job cards; estimates; checklist.
Tools and items for this unit
Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Level 1 items are defined in the Level 1 appendix; the Level 2 appendix adds the new ones.
| Item | What it is and what it does | Type or size (typical) | Care or safety | Also called |
|---|---|---|---|---|
| Job card | A form that travels with the car: complaint, findings, estimate, approval, work, parts and final check. | A5 or A4 duplicate book | Keep copies. | work order, repair order |
| Estimate form and receipt | The estimate lists expected parts and labour. The receipt proves payment. | Duplicate carbon books | Customer signs the estimate. | quotation, quote |
| Warning triangle | A reflective triangle placed behind a stopped vehicle to warn traffic. | Folding red triangle | Reported as a legal need in the press; not verified. Carry one. | hazard triangle |
| Fire extinguisher and first-aid kit | Workshop safety items. See Level 1. | See Level 1 | Check dates. | fire extinguisher bottle; first aid box |
| Seat and steering-wheel covers, wheel-arch covers | Disposable covers that protect the customer's car from oil and dirt. | Paper or plastic | Use on every job. | no other common name found |
| Used-oil and coolant containers, waste log | Labelled sealed containers and a log of what was collected, when and by whom. | Drums with lids | Ask the EPA about collection. | antifreeze |
Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer about warranties, disputes or customer contracts. For waste, ask the EPA. For tax, check with GRA or a qualified accountant. For any repair that affects safety, a qualified mechanic or GhIE-registered engineer must check the work.
The job card
A job card is the paper (or file) that travels with the vehicle: customer, number plate, mileage, complaint, inspection findings, estimate, approval, work done, parts used, hours, and the final check. The usual order is: inspect, build an estimate, get approval, work, then invoice. A California regulator's guide also describes a work order that holds the authorised estimate and the odometer reading.
Estimates and approval
- Write an estimate that describes the job and lists parts and labour. One California regulator accepts a signature on the estimate as the customer's consent for the job. Ghana's rules for repair estimates were not verified; ask a qualified lawyer.
- If you find extra faults, stop and ask before doing more work. Record who agreed, and when.
- Keep deferred items on the job card: "tyres worn; advise replacement within the month".
- Give the customer's old parts back if they want to see them.
Quality checklist (final inspection)
- Job done as agreed; every item on the card ticked.
- Torque. Wheel nuts and critical bolts tightened to the manual.
- Fluids at the right levels; no leaks after a test run.
- No tools left in the engine bay; caps and covers fitted.
- Brakes and steering checked by a qualified mechanic if touched.
- Road test done safely; no noises, no pulling.
- Clean. Seats and steering wheel free of oil; old parts bagged.
- Warning lights off; scan clear and recorded.
- Waste stored properly.
Roadworthiness and the law
A roadworthiness certificate comes from DVLA through a designated private vehicle testing station, with the vehicle and its registration certificate. In 2026 DVLA closed six testing centres for issuing reports without proper inspection. Never promise or sell a roadworthy sticker. New Road Traffic Regulations, 2026 (L.I. 2519) are reported in the press. Their tyre, brake and roadside-repair rules and the status of the older 2012 rules were not verified: the gazetted text was not read. Ask DVLA.
Waste, again
The EPA has warned that garage waste can pollute drains, soil and groundwater. Collect used oil, filters, brake fluid, coolant and batteries separately in labelled containers. Act 1124 now governs environmental protection, including hazardous waste; used-oil rules were not verified. Ask the EPA office.
Talking to customers
Use plain words: "Your pads are thin. If we wait, the discs will be damaged and it will cost more." Show the part. Give a price range, then the final price. Never frighten people with exaggeration, and never say a repair is "safe" if you have doubts.
Estimate
Example: front pads GH¢250 a set, a brake cleaner can GH¢30, brake fluid GH¢35, labour GH¢150. The customer approves only pads and labour; later you find a leaking hose, GH¢120 part plus GH¢50 labour. (1) Estimate for the first job? (2) What do you do about the hose? (3) New total if the customer approves it?
Job card to hand-over
- Take a vehicle in. Interview the owner; write the job card.
- Inspect and write findings with photos (with permission).
- Write the estimate and have it approved.
- Do an approved job (for example an oil service).
- Run the final checklist.
- Hand over in plain words and keep a copy of the card.
Write an apology
Write a short, honest message to a customer for a job that will be a day late. Say why, what you will do, and when.
Check yourself: Unit 6
- What do you do if you find an extra fault during a job?
- Who issues a roadworthiness certificate?
- Name two items on a final checklist.
Unit 7 · Your location, small business and marketing
At Level 1 you made a plan. At Level 2 you test it with real numbers and real customers.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 7.1 Choose a location | compares sites by traffic, rent, safety and permits |
| 7.2 Price and cash flow | prices jobs, forecasts one month and sets a deposit rule |
| 7.3 Market yourself | uses WhatsApp Business, Google Business Profile, signs and referrals |
| 7.4 Know the rules | lists registration, tax and permit steps |
| 7.5 Include everyone | names tasks and adjustments for persons with disabilities |
Range. Small garage or mobile service. Evidence. Costed plan; one-month forecast; marketing page.
Tools and items for this unit
Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Level 1 items are defined in the Level 1 appendix; the Level 2 appendix adds the new ones.
| Item | What it is and what it does | Type or size (typical) | Care or safety | Also called |
|---|---|---|---|---|
| Cash book and receipt book | Daily record of money in and out; proof of payment to customers. | Exercise book or ledger | Keep records safe. | no other common name found |
| Quote sheet and price list | A one-page price list for common jobs. | Laminated page | Update when prices change. | no other common name found |
| WhatsApp Business and Google Business Profile | Free tools that show your services and map location to customers. | Phone apps | Keep details correct. | no other common name found |
Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer before you act on any legal, licence or registration matter. For tax, VAT, PAYE and SSNIT, check with GRA or a qualified accountant. For loans and insurance, ask your bank or a licensed financial adviser. For workshop safety, ask a qualified mechanic or a GhIE-registered engineer.
Location settings that give good returns
- Close to taxi, trotro and minibus ranks, where drivers need quick service
- In a garage cluster such as Kokompe, where customers and master mechanics are
- Beside a spare-parts shop with a good relationship, so you can fetch parts quickly
- Near a busy road with level, dry ground and safe parking
- Mobile service for offices and estates with fleet vehicles
- A place with water, shade, safe storage for oil and parts, and a way to keep waste away from drains
Business ideas and ingenuity
- Service contract for a small fleet of taxis, school buses or farm pickups
- Pre-purchase inspection report for people buying second-hand cars (look-and-report; written list)
- Brake and tyre safety check days for commercial drivers
- Mobile battery testing and jump-start service
- Diagnostic service with a scan tool, sold as a "diagnosis first" package
- Selling wiper blades, bulbs, fuses and oil with every service
Money maths
One month
Example figures. Your mobile service does 30 oil services a month at GH¢500 each (parts and labour). Parts and consumables cost GH¢300 per service. Fuel and transport GH¢600 a month. Phone and data GH¢150. Tool repair and replacement GH¢250. (1) Monthly income? (2) Monthly costs? (3) Profit? (4) What is the profit per service?
Register and permits
- Business name: GH¢130 to register, GH¢70 a year to renew. Your Ghana Card number is your tax number.
- A sole trader below the turnover ceiling may use the Modified Taxation Scheme; GRA says up to GH¢20,000 turnover pays fixed instalments, and GH¢20,001 up to 750,000 pays 3% of turnover. Check with GRA or an accountant.
- Assembly permit: STMA's garage fee was not verified. Ask STMA.
- Workplace safety law applies to workshops; the Factories Inspectorate inspects.
Market yourself
- WhatsApp Business: profile, catalogue of services with prices from, quick replies ("Hello, thank you for contacting..."), and labels for new, quoted, booked and done.
- Google Business Profile: your location, hours, photos and reviews.
- Signs and uniforms: a clear sign, a branded shirt, a card.
- Referrals: a small thank-you to drivers who recommend you.
- Portfolio: photographs of work, with permission; a testimonial from a customer.
Accessibility
The Persons with Disability Act 2006 exists; ask the National Council on Persons with Disability or a lawyer about it. The Assemblies' disability fund now supports skills and assistive devices. Suggested (author's reasoning, not sourced) adjustments:
| Task | Notes and adjustments |
|---|---|
| Scan tool diagnosis, test records, estimates | Bench work; a raised bench with knee space suits wheelchair users |
| Customer service, parts counter, bookkeeping, WhatsApp marketing | Workable for most disabilities |
| Fluid and filter work, tyre checks | Workable with a stool or trolley and good lighting |
| Hearing-impaired trainees | Written job cards, visual signals, vibrating or light alarms |
| Visually impaired trainees | Customer service, sales, parts and bookkeeping; tactile tool boards |
| Lifting, under-car work, heavy wheel handling | Needs full mobility or a partner; plan team roles |
Plan, forecast, pitch
- Choose a service and a location. Give three reasons.
- List your tools, their cost (from local quotes) and your running costs.
- Build a one-month forecast like the exercise, using your real quotes.
- Write your WhatsApp Business profile and sign.
- Name your permit steps and who you must ask.
- Present your plan in five minutes.
Ask for a referral
Ask a taxi or trotro driver what they look for in a mechanic. Write three answers and one thing you would change in your plan.
Check yourself: Unit 7
- Name two good locations for a garage or mobile service.
- What does the business name cost to register in 2026?
- Name one task that suits a wheelchair user.
Glossary
| Term | Meaning |
|---|---|
| Alignment | Setting the angles (toe, camber, caster) of the wheels |
| ABS | Anti-lock braking system; keeps wheels from locking in hard braking |
| Bleeding | Removing air from the brake or cooling system |
| Camber | The tilt of the wheel in or out at the top |
| Caliper | The part that squeezes the pads against the disc |
| Compression | The pressure made when the piston squeezes the air and fuel |
| Freeze-frame | The engine data saved when a code was set |
| Interference engine | An engine where a broken timing belt can let pistons hit valves |
| Job card | The paper that records a repair from start to finish |
| Parasitic drain | Current that flows when the car is off |
| Thermostat | A valve that controls coolant flow to keep the engine at working temperature |
| Toe | How far the wheel fronts point in or out |
Logbook
Copy these pages into an exercise book. Your logbook is part of your assessment evidence.
- Unit 1: diagnosis drill; four-line diagnoses
- Unit 2: brake inspection report; pad job record; bleed record; qualified check signed
- Unit 3: suspension and steering inspection; tyre wear notes; repair cost
- Unit 4: plug readings; compression results; belt interval record
- Unit 5: voltage logs; charging test; cooling system service
- Unit 6: job cards; estimate; final checklist
- Unit 7: one-month forecast; marketing page; plan
- Every homework, dated
Self-check quiz
- Does a trouble code name the broken part?
- Why replace brake pads in axle sets?
- Why must a brake caliper not hang from its hose?
- In what order do you usually bleed brakes, and what must you not let happen?
- What does cupped tyre wear point to?
- What must you check before blaming ball joints?
- What are the four strokes?
- What is a rule-of-thumb running battery voltage for good charging?
- Why do a pressure test only on a cold engine?
- What do you do if you find an extra fault mid-job?
- Who issues a roadworthiness certificate?
- How much is it to register a business name in 2026?
Appendix A · Diagnosis card and fault-finding charts
Test the cheapest likely idea first. Write the numbers. Each chart says what to measure and what the reading means. Numbers are typical; the workshop manual rules.
Ask a qualified expert. Fuel, brake, steering, airbag and electrical faults can injure people. Test only what this book shows. For anything else ask a qualified mechanic, an auto electrician or a GhIE-registered engineer. Never road test a car with a brake or steering fault.
A0 · The seven-line diagnosis form
| Line | Write |
|---|---|
| 1 Complaint | What the customer said, in their words |
| 2 Conditions | When: cold or hot, speed, load, braking, turning |
| 3 Findings | What you saw and measured, with numbers |
| 4 Cause | What you believe and why |
| 5 Repair | What was done, parts used |
| 6 Proof | The test after repair that shows the fault is gone |
| 7 Advice | What can wait, and when to come back |
A1 · Hard start, hot and cold
| Step | Test | Meaning |
|---|---|---|
| 1 | Battery rested voltage | Below about 12.2 V: charge and load test |
| 2 | Voltage while cranking | A healthy battery stays about 10 V or more (typical; not verified) |
| 3 | Terminals, earth strap | Hot or loose: clean and tighten |
| 4 | Codes and freeze frame | Note conditions |
| 5 | Hot start only | Starter heat, fuel pressure (qualified supervision) |
| 6 | Cold start only | Plugs, battery, glow plugs on a diesel |
A2 · Rough idle and misfire
| Step | Test | Meaning |
|---|---|---|
| 1 | Codes P0300 to P0304 (Appendix B) | Which cylinder |
| 2 | Look for air leaks, cracked hoses | Idle too lean |
| 3 | Plug condition, gap | Worn or fouled plug |
| 4 | Swap coil between cylinders | If misfire moves, the coil is faulty |
| 5 | Compression test | Low cylinder: valves or rings |
A3 · Loss of power
| Step | Test | Meaning |
|---|---|---|
| 1 | Air filter | Blocked: replace |
| 2 | Codes | Misfire, air flow or fuel codes |
| 3 | Exhaust restriction (smell, heat, back pressure; refer) | Blocked catalyst |
| 4 | Fuel quality, filter service date | Bad fuel possible |
| 5 | Clutch slip (manual) or brake drag | Check with a qualified mechanic |
A4 · High fuel use
| Step | Test | Meaning |
|---|---|---|
| 1 | Tyre pressures | Low pressure raises use |
| 2 | Air filter | Blocked filter |
| 3 | Brakes dragging | Hot wheel after a drive |
| 4 | Codes (rich mixture) | P0172 family |
| 5 | Driving style, load, A/C use | Habits |
A5 · Smoke
| Colour | Causes to test |
|---|---|
| Blue | Oil burning: rings, valve seals, PCV valve; check oil use |
| White, sweet, thick | Coolant in cylinders: pressure test; refer |
| Black | Rich: air filter, injectors (refer), a diesel's air or fuel setting |
| Grey | Mixed causes; use codes |
A6 · Noise by place
| Place and when | Likely area |
|---|---|
| Front, over bumps | Shock, bush, anti-roll bar link, ball joint |
| Front, turning | CV joint or tie rod end |
| Wheel, changes with speed, not with steering | Wheel bearing or tyre |
| Brake, light pedal | Pad wear indicator or dust |
| Brake, grinding | Metal on metal: stop |
| Engine, ticking | Low oil, valve noise; check oil level first |
| Engine, knock under load | Wrong fuel or worn parts; refer |
A7 · Brake faults
| Sign | Test | Meaning |
|---|---|---|
| Soft, sinking pedal | Fluid level, leaks | Leak or air: stop, refer |
| Pulls to one side | Tyre pressure, caliper drag | Seized caliper or uneven pads |
| Pulsing pedal | Disc runout (dial gauge) | Warped or uneven disc |
| Squeal | Pads, dust, glazing | Inspect |
| Long pedal travel | Drum adjusters, air | Adjust or bleed |
A8 · Steering and handling
| Sign | Test | Meaning |
|---|---|---|
| Wander | Tyre pressures, play at tie rod ends | Worn parts or alignment |
| Pull | Pressure, brake drag | Alignment or tyres |
| Vibration at speed | Balance, damage, loose nuts | Wheel balance |
A9 · Battery goes flat overnight
| Step | Test |
|---|---|
| 1 | Interior lights or boot light staying on? |
| 2 | Recharge the battery, load test it |
| 3 | Measure parasitic draw (see Appendix F) |
| 4 | Remove fuses one at a time to find the circuit |
A10 · Charging light stays on
| Step | Test |
|---|---|
| 1 | Belt present and tight |
| 2 | Running voltage at idle (13.8 to 14.4 V is typical) |
| 3 | Connections at the alternator |
| 4 | Refer an alternator failure to an auto electrician |
A11 · Overheating by cause
| Cause | Sign |
|---|---|
| Low coolant, leak | Level low, puddles |
| Fan fault | Hot at idle, better when moving |
| Thermostat stuck closed | Upper hose hot, lower hose cool, fast rise |
| Blocked radiator | Mud or old coolant |
| Head gasket (refer) | Bubbles in coolant, white smoke |
A12 · Cranks, no start
| Step | Test |
|---|---|
| 1 | Fuel in the tank |
| 2 | Fuel pump hum on key on |
| 3 | Spark and codes (qualified supervision) |
| 4 | Immobiliser or key light |
| 5 | Timing belt broken (no compression; refer) |
Appendix B · OBD code guide
A code gives an area, not a part. Read freeze frame, then test.
Ask a qualified expert. Do not replace parts on a code alone. For emission, fuel-system or airbag codes ask a qualified mechanic or auto electrician.
Anatomy. Letter: P powertrain, B body, C chassis, U network. Second character: 0 is a generic code. Sources differ on the other digits, so check SAE J2012 and ISO 15031-6 (international standards) before relying on them. Last three characters: locate the fault.
| Group | Area |
|---|---|
| P00xx to P02xx | Fuel and air metering |
| P03xx | Ignition and misfire |
| P04xx | Emission controls |
| P05xx | Idle and speed |
| P06xx | Computer and outputs |
| P07xx to P09xx | Transmission |
| Code | Usual title (typical; read your scan tool's wording) | First checks |
|---|---|---|
| P0100 | Mass air flow circuit | Connector, air leaks, dirty sensor |
| P0101 | Mass air flow range or performance | Air filter, intake leaks |
| P0102 | Mass air flow low | Wiring, sensor |
| P0113 | Intake air temperature high | Connector |
| P0115 | Coolant temperature circuit | Connector |
| P0118 | Coolant temperature high | Sensor, wiring |
| P0120 | Throttle position sensor circuit | Connector |
| P0128 | Coolant below thermostat temperature | Thermostat, level |
| P0130 | Oxygen sensor circuit bank 1 | Wiring, exhaust leak |
| P0171 | System too lean | Air leaks, filter |
| P0172 | System too rich | Air filter, leaks |
| P0300 | Random misfire | Plugs, coils, fuel |
| P0301 to P0304 | Misfire cylinder 1 to 4 (P0301 Source: Klavkarr OBD) | That cylinder's plug and coil |
| P0325 | Knock sensor circuit | Wiring |
| P0335 | Crankshaft position sensor | Connector; refer |
| P0340 | Camshaft position sensor | Connector; refer |
| P0401 | EGR flow insufficient | EGR passages |
| P0420 | Catalyst efficiency below threshold, bank 1 | Exhaust leaks and misfires first |
| P0442 | Small evaporative leak | Fuel cap |
| P0455 | Large evaporative leak | Cap, hoses |
| P0500 | Vehicle speed sensor | Connector |
| P0505 | Idle control system | Throttle body, air leaks |
| P0562 | System voltage low | Battery, charging |
| P0563 | System voltage high | Regulator; refer |
| P0600 | Serial communication link | Refer |
| P0700 | Transmission control system | Refer |
| U0100 | Lost communication with the engine computer | Battery, wiring; refer |
Freeze frame: the engine conditions when the code was stored. Readiness monitors: self-tests the car runs; clearing codes resets them. Pending code: seen once. Confirmed code: seen again. A code is not a diagnosis. Do not clear a code to hide a fault. Do not replace the oxygen sensor on P0420 before checking exhaust leaks and misfires (typical diagnostic practice).
Appendix C · Brake reference
Brake work stays supervised and checked at this level.
Ask a qualified expert. Brake work decides lives. Have a qualified mechanic or GhIE-registered engineer check every brake job and the first road test.
Fluid. DOT 3 minimum boiling points dry 205 C and wet 140 C; DOT 4 dry 230 C and wet 155 C; DOT 5.1 and DOT 5 dry 260 C and wet 180 C. DOT 5 is silicone: do not mix. This is a USA regulation used as an international reference; check against the Ghana Standards Authority text when it is read.
Replacement limits. Pad: about 3 mm is a common warning. Disc: the minimum thickness is stamped on the disc; use that figure.
Hydraulic area ratio. Force multiplication = (caliper piston diameter / master cylinder diameter) squared. Example: 50 mm and 20 mm gives (50/20)^2 = 6.25 (checked by script). Pedal lever ratio multiplies this again.
Bleeding. Fill to MAX; follow the manual's order; keep the reservoir full; close the nipple before the foot lifts.
- Pads and discs measured and recorded
- Hoses checked
- Fluid level and grade correct
- Sliders cleaned and greased as the manual says
- Wheel nuts torqued in a star pattern
- Pedal firm; handbrake tested
- Qualified mechanic's check and road test
Appendix D · Suspension, steering and tyre wear
Ask a qualified expert. Suspension and steering failures cause crashes. Never use a spring compressor. Ask a qualified mechanic to check any such repair.
| Alignment term | Meaning |
|---|---|
| Toe | Whether the fronts of the wheels point in or out |
| Camber | Tilt of the wheel top, in or out |
| Caster | Forward or backward tilt of the steering axis; it helps the wheel return to straight |
| Tyre wear pattern | Likely cause |
|---|---|
| Both edges | Low pressure |
| Centre | High pressure |
| One edge | Camber or toe, or worn parts |
| Cupping | Worn shocks or imbalance |
| Feathering across the tread | Toe |
| Flat spots | Locked wheels |
Play checks: wheel at 12 and 6 o'clock for ball joints and bearings; at 3 and 9 o'clock for tie rods (see Unit 3). Do the alignment after any steering or suspension part is replaced.
Appendix E · Tune-up reference
Ask a qualified expert. Fuel is flammable and under pressure; ignition voltage can shock. Ask a qualified mechanic before fuel-system or timing work.
| Item | Typical guidance |
|---|---|
| Spark plug gap | Use the figure in the manual; check with a gauge |
| Plug reading | Light tan or grey: normal; black: rich; oily: oil; white: hot |
| Compression | Lowest cylinder not more than about 15 percent below the highest |
| Wet test | Oil added: reading rises means rings; stays low means valves |
| Timing belt versus chain | Belts have a replacement interval; chains usually do not |
| Four-stroke | Intake, compression, power, exhaust |
Compression worked sum: (150 - 120) / 150 = 20 percent (checked by script), above the 15 percent rule of thumb.
Appendix F · Starting, charging and cooling tests
Ask a qualified expert. Batteries can burst; coolant scalds. Work on 12-volt systems only. Ask a qualified mechanic or an auto electrician for more.
| Rested voltage (typical) | State |
|---|---|
| 12.6 V or more | Full |
| about 12.4 V | about three-quarters |
| about 12.2 V | about half |
| about 12.0 V | about one-quarter |
| 11.9 V or less | Flat |
Sources differ by about 0.1 V per step. Running voltage 13.8 to 14.4 V at idle; another source gives 13.5 to 14.8 V. Load test: follow the tester's steps. Alternator test: Unit 5. Parasitic draw: put the meter in series on the amp range; the allowed draw depends on the car, so use the manual (a typical figure is not verified). Cooling pressure test: cold only, to the cap's rating. Coolant mix: use the manual; 50 percent is common.
Appendix G · Forms to copy
Written estimates are good practice. Whether Ghana law requires them was not verified; one California regulator describes the estimate and signature.
G1 · Job card
| Field | Entry |
|---|---|
| Customer, plate, make, model | |
| Mileage in | |
| Complaint | |
| Inspection findings | |
| Estimate (parts and labour) | |
| Customer approval, date, signature | |
| Work done and hours | |
| Parts used with part numbers | |
| Final checks and road test | |
| Advice and next service |
G2 · Estimate and approval
| Item | Parts | Labour | Total |
|---|---|---|---|
| Customer approval (tick) | |||
| Extra work found: stop, explain, price, approve |
G3 · Parts and labour sheet
| Part | Part number | Supplier | Cost | Price to customer |
|---|---|---|---|---|
G4 · Road-test form
| Check | Result |
|---|---|
| Pedal firm at walking pace | |
| Car stops straight | |
| Handbrake holds | |
| No noises, no pulling | |
| Warning lights off | |
| Wheel nuts rechecked |
G5 · Pre-delivery checklist
- Job done as agreed; card ticked
- Torque to the manual; no tools left in the engine bay
- Fluids correct; no leaks
- Lights and horn work
- Seats and steering wheel clean
- Old parts bagged
- Waste stored correctly
- Customer told what you did and what can wait
Appendix H · Formula card
All numbers are examples and were checked by script.
| Job | Formula | Worked example |
|---|---|---|
| Pressure units | 1 psi = 6.894757 kPa | 32 psi = 220.6 kPa |
| Torque units | 1 lb-ft = 1.3558 N.m | 100 lb-ft = 135.6 N.m |
| Fuel use | litres / km x 100 | 40 L over 480 km = 8.33 L per 100 km |
| Engine capacity | pi/4 x bore squared x stroke x cylinders | bore 80 mm, stroke 90 mm: 452.4 cm3 per cylinder, 1809.6 cm3 for 4 |
| Compression ratio | (swept + clearance) / clearance | (452.4 + 50) / 50 = 10.05 |
| Power | kW = torque (N.m) x rpm / 9549 | 150 N.m at 4000 rpm = 62.8 kW (about 84.3 hp) |
| Tyre diameter | rim x 25.4 + 2 x width x ratio | 205/55 R16 = 631.9 mm |
| Speedometer error | new diameter / old diameter | 215/55 R16 is 642.9 mm; 1.74 percent bigger; at 100 km/h shown the true speed is 101.7 |
| Road speed | rpm x circumference x 60 / (gear ratio x final drive x 1000) | 3000 rpm, 0.85 top, 4.1 final: 102.5 km/h |
| Brake area ratio | (piston / master) squared | (50/20)^2 = 6.25 |
| Stopping idea | reaction + braking | at 60 km/h, 1 s: 16.7 m + 23.1 m at 6 m/s squared (example) = 39.8 m |
| Ohm's law | V = I x R | 12 V, 4 ohm: 3 A |
| Battery reserve | Ah / A | 60 Ah at 5 A: 12 h (theory; real is less) |
| Parasitic drain | Ah / A | 60 Ah at 0.05 A: 1200 h, 50 days |
| Compression difference | (high - low) / high | (150 - 120)/150 = 20 percent |
| Pad wear | (new - now) / new | (9 - 3)/9 = 67 percent worn |
Appendix I · Illustrative cases
These eight cases are written for training. They are not records of real jobs, and no names are used. Each uses the seven-line form.
Ask a qualified expert. Cases are examples of method, not repair instructions. Ask a qualified mechanic before any safety repair.
| Case | Complaint | Findings | Cause | Repair and proof |
|---|---|---|---|---|
| 1 Flat battery | Car will not start in the morning | 11.8 V rested; running 13.9 V | Interior light left on by a faulty door switch | Recharge, fix switch, drain test shows low draw |
| 2 Overheating | Temperature rises in traffic | Coolant low; fan does not start | Failed fan relay | Replace relay; fan runs; no overheating on road test |
| 3 Misfire | Rough idle | P0302; plug fouled | Cylinder 2 coil weak | Swap coil: misfire moves; replace coil; no code |
| 4 Brake pull | Car pulls left on braking | Tyre pressures equal; left caliper hot | Seized slider | Clean, grease, replace pads in sets |
| 5 Squeal | Squeal when braking | Pads at 2 mm | Wear indicator | Replace pads in axle sets; check disc thickness |
| 6 Vibration | Shake at speed | Cupped tyre wear | Worn shocks | Replace shocks in pairs; alignment |
| 7 Charging light | Light on at night | 12.4 V running | Loose alternator belt | Adjust or replace belt; 14.1 V |
| 8 Hard start hot | Slow crank when hot | 9.6 V cranking | Poor battery earth strap | Clean and tighten; crank voltage improved |
Appendix J · Mistakes, decisions and Ghana rules
Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer or the named office before acting on any law, permit or waste rule.
Eight expensive mistakes. Swapping parts without testing. Clearing a code and sending the car away. Reusing crush washers. Mixing brake fluid types. Not torquing wheel nuts. Letting the brake reservoir run dry while bleeding. Leaving tools in the engine bay. Changing pads on one side only.
| Decide | Rule | Action |
|---|---|---|
| Disc below its stamped minimum | Replace | Both discs on an axle |
| Pad at about 3 mm | Plan replacement | Axle set |
| Tyre cut or bulge | Unsafe | Replace |
| Soft brake pedal | Do not drive | Refer |
| Hose cracked or soft | Replace | Hose set |
| Airbag, ABS, high voltage, fuel pressure | Refer | Qualified specialist |
| Topic | What is known | Status | Ask |
|---|---|---|---|
| Road Traffic Regulations 2026 (L.I. 2519) | Reported by the press | Text not read; not verified | DVLA |
| Roadworthiness | Certificate via a designated private testing station | Fees not verified | DVLA |
| Imported used vehicles | GSA conformity programme under GS 4510 | Age limit not verified | The Ghana Standards Authority |
| Garage waste | Environmental Protection Act 2025 (Act 1124) | Used-oil rules not verified | EPA Western Region |
| Workshop safety | Factories, Offices and Shops Act 1970 | Details not verified | Factories Inspectorate |
| Fuel and parts quality | Roadside fuel can be poor; fake parts are reported | Advice only | NPA, dealers |
Typical service items (the maker's schedule governs; no kilometre figures are printed because they depend on the car): engine oil and filter; air filter; fuel filter; spark plugs; coolant; brake fluid; gearbox and differential oil; belts; timing belt or chain; tyre rotation; battery check; wipers; lights. In dust and heat, use the maker's severe-use schedule if it lists one.
Appendix K · Tools, Measuring Instruments and Parts
The Level 1 appendix defines the first 100 items; this appendix adds the new ones. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture.
| Item | Type or size (typical) | What it is and what it is used for | How to read or use | Also called |
|---|---|---|---|---|
| Borescope | Small camera on a flexible probe | Looks inside a cylinder or tube | Use with the engine off | no other common name found |
| Clamp meter | DC clamp | Measures current without cutting the wire | Clamp one wire | tong tester, current clamp |
| Compression tester | Screw-in type | Reads cylinder pressure | Throttle open, several turns | compression gauge |
| Dial gauge | 10 mm range | Measures runout and small movement | Zero first | dial indicator |
| Feeler gauge | 0.05 to 1 mm | Measures small gaps | Try blades until a light drag | thickness gauge, feeler blade |
| Hydrometer | Flooded batteries | Reads acid strength | Read at eye level | specific-gravity tester |
| Mechanic's stethoscope | Probe and ear tubes | Finds the place of a noise | Keep away from moving parts | no other common name found |
| Micrometer | 0 to 25 mm | Measures thickness | Read barrel then thimble; zero first | mic, screw gauge |
| Refractometer | Hand-held | Reads coolant mix from a drop | Calibrate on clean water | coolant tester |
| Thread gauge | Blades | Reads thread pitch | Match the blade to the thread | no other common name found |
| Vacuum gauge | Dial | Reads manifold vacuum | Hose to the intake | no other common name found |
| Vernier caliper | 150 mm | Measures lengths and diameters | Zero first; read to 0.02 mm | slide calliper |
| Brake pressure bleeder | Pump and cap | Pushes fluid through the system | Use the right cap | no other common name found |
| Gasket and sealant | Paper, rubber or paste | Seals joints | Clean faces; use the type the manual says | no other common name found |
| Hose clamp and clamp pliers | Screw, spring or crimp | Hold hoses on | Use the right type | pincers |
| Thermostat | Rated by opening temperature; check the manual | Opens at a set temperature | Match the rating | no other common name found |
| Wheel stud and nut | Thread by car | Fastens the wheel | Check threads | wheel bolt |
| Fuel pump, injector, throttle body | Parts of the fuel and air system | Pump fuel; spray fuel; control air | Look and report; refer | fuel injector |
Appendix L · Abbreviations and index
| Short | Meaning |
|---|---|
| ABS | Anti-lock braking system |
| ATF | Automatic transmission fluid |
| CV | Constant velocity joint |
| DTC | Diagnostic trouble code |
| EGR | Exhaust gas recirculation |
| MAF | Mass air flow sensor |
| MAP | Manifold absolute pressure sensor |
| OBD | On-board diagnostics |
| PCV | Positive crankcase ventilation |
| TPS | Throttle position sensor |
Where to find it. Fault charts: Appendix A. OBD codes: Appendix B. Brakes: Unit 2 and Appendix C. Suspension: Unit 3 and Appendix D. Tune-up: Unit 4 and Appendix E. Electrical tests: Unit 5 and Appendix F. Forms: Appendix G. Formulas: Appendix H. Cases: Appendix I. Ghana rules: Appendix J. Tools: Appendix K.
Further reading and sources
Best next reads: the workshop manual for any car you work on; Auto Mechanics Basics Level 3 for advanced diagnostics, driveline, modern vehicles and running your own garage; the Hub's Money Skills Level 2 and Entrepreneurial Thinking Level 2 for money and business basics.
What this module does not cover: brake lines and ABS repair, spring compression, steering rack repair, timing belt replacement on your own, fuel-system pressure work, gearbox and clutch repair (Level 3), hybrid and electric vehicles, car air-conditioning gas, and Ghana parts prices (not found reliably). DVLA fees and NVTI trade-test grades were not verified.
Every source used in this manual is listed, with links, in the Teacher Copy.