← All training manualsAuto Mechanics Basics Level 3 · read-onlyGet the PDF with Teacher Copy (GH¢50)
Level 3 · Advanced · CTVET formatTrainee Manual

Auto Mechanics Basics Level 3

Diagnose with data, know where your skills end, supervise a safe workshop, then register, keep the books and grow a garage people trust.

A car raised on jack stands with a mechanic checking the wheel A saloon car with its front raised on a trolley jack and two jack stands, a wheel off beside it, and a mechanic in overalls and safety boots tightening a wheel nut with a wrench. To the left, a toolbox and an oil can. To the right, a tyre stack and a battery. Wheel chocks sit behind the rear wheel. TOOLS · OILJACK STANDS FIRSTBATTERY
Trainee name
Training centre
Workshop
Start date
Prepared by De-Graft Afful · Version 1.1.0 · November 2026
01

About this module

Level 2 made you good at repairs. Level 3 makes you trusted: by customers with fleets, by your own staff and apprentices, and by the bank and the tax office.

Who it is for. People who have finished Auto Mechanics Basics Level 2, or who can show the same skills. In Ghana's framework, National Proficiency II leads to National Certificate I, which covers complex work with minimum supervision. This module sits at about that level.

CTVET status. CTVET's list of competency-based programmes shows "Automotive Mechanic" at NP I and NP II, approved 28 April 2020, with an expiry of 27 April 2025 on the page we read. The unit list was not found online, so this module is not that curriculum, and it does not certify you as a mechanic, inspector or engineer. Ask CTVET or NVTI for the current standard and trade-test rules (not verified).

Bridge from Level 2: what you already know

  • Diagnosis by method; codes and freeze-frame data; the four-line diagnosis
  • Brake inspection, pad replacement in axle sets and bleeding under supervision; the qualified mechanic's check
  • Suspension and steering play checks; tyre wear patterns; why alignment follows repairs
  • Four strokes; plugs; compression tests; timing belt limits
  • Battery, charging, starter and cooling tests with a multimeter and pressure tester
  • Job cards, estimates, approval and the final checklist; DVLA roadworthiness
  • Location, one-month forecast, WhatsApp Business, registration of a business name

Level 2 did not cover circuit and data diagnosis in depth, clutches and driveline, modern injection and high-pressure diesel, hybrid and electric vehicles, workshop lifting and supervision, company registration, accounts or growth. This manual does. For general bookkeeping and venture basics, see the Hub's Money Skills Level 2 and Entrepreneurial Thinking Level 2.

How the module works

Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent. About 70% of the time is practical.

02

Safety first

  • Lifting: never go under a vehicle supported only by a jack or by a lift whose locks are not engaged. Use rated stands or the lift's mechanical locks.
  • Brakes, steering, high-voltage and fuel pressure: a qualified mechanic checks every brake and steering job; no one works on orange high-voltage cables without specific training; high-pressure diesel lines are never loosened to "check".
  • Fire, exhaust and fumes: engines run outdoors or with extraction; no flames near fuel.
  • Waste: used oil, filters, brake fluid, coolant and batteries stored in labelled containers; ask the EPA.
  • Engineer sign-off: structural, lifting-equipment and workshop building matters need a GhIE-registered engineer.
03

Unit 1 · Advanced diagnostics

The easy faults you fix in an hour. The hard ones, the ones that come and go, are where your reputation is made.

Competency standard

Learning outcome Performance criteria — the trainee…
1.1 Use scan data reads live data and freeze-frame; compares with expected values
1.2 Test circuits measures voltage, voltage drop and continuity safely; draws a simple circuit
1.3 Trace intermittent faults uses logging and wiggle tests
1.4 Prove the repair repeats the conditions and confirms the fault is gone
1.5 Know the limits refers ABS, airbag, immobiliser, high-voltage and fuel-pressure faults

Range. Light petrol and diesel vehicles; 12-volt circuits. Evidence. Written diagnoses; observation; circuit tests.

Tools and items for this unit

Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Earlier-level items are in the Level 1 and Level 2 appendices.

Item What it is and what it does Type or size (typical) Care or safety Also called
Test light A probe with a bulb and a lead that glows when voltage is present. It is a quick check, not a measurement. 12 V type for car work only Do not probe computer circuits; it can draw too much current. circuit tester, test lamp
Back-probe pin A thin pin pushed alongside a wire inside a connector to measure voltage without cutting the wire. Fine pins for connectors Seal and do not pierce insulation. no other common name found
Breakout box A box that sits between a connector and its socket and brings each pin out for testing. Made for a connector type Use as the maker's manual shows. BOB
Oscilloscope (scope) A tool that draws voltage against time, so you can see a sensor signal change. Two to four channel types Training is needed; refer if unsure. scope, lab scope
Clamp meter Measures current by clamping round a wire, no cut needed. DC clamp up to about 100 A (typical) One wire only. tong tester, current clamp
Scan tool with live data Reads live data parameters called PIDs (parameter identifiers) such as coolant temperature and fuel trim. Professional or good dongle Log data while the fault happens. code reader, scanner, diagnostic tool
Wiring diagram A drawing of a circuit with symbols for fuses, relays, switches, motors and connectors. From the workshop manual Know the symbols before you read. circuit diagram, schematic
Jumper wire and fused jumper A short wire with clips used to bypass a circuit for testing. A fused jumper has a fuse in it. Fused, 10 A Never bridge the ECU or airbag circuits. blade fuse; bypass wire

Ask a qualified expert. Electrical and electronic faults can cause fires, airbag deployment and shocks. Work only on 12-volt circuits, disconnect the battery where the manual says, and never pierce wires without sealing them. Ask a qualified mechanic, an auto electrician or a licensed electrician about anything beyond these tests; ask a GhIE-registered engineer about vehicle modifications that affect safety.

From codes to data

A code is five characters. P0 codes are generic and the same on most makes; P0300 is a random misfire and P0420 catalyst efficiency are examples. The code only points to a system. Live data shows what the sensors say right now: coolant temperature, engine speed, throttle position, air flow, fuel trims and oxygen sensor readings. A good diagnosis asks: Does this sensor value make sense? A cold engine that reads 120 degrees C coolant temperature means a sensor or wiring fault, not a hot engine.

Ohm's law and voltage drop

A 12-volt circuit works like water in a pipe. Voltage (V) is the push, current (I, amps) is the flow, resistance (R, ohms) is the narrowing. V = I x R. A bad connection adds resistance, so some of the battery's push is lost as heat before it reaches the load. That loss is the voltage drop.

To test: run the circuit, put the voltmeter across the wire or connection (not across the load), and read the volts lost. A small drop is normal; a large one shows a bad joint or cable. Limits differ by circuit, so use the manual's figure (not verified here).

Circuit sums

(1) A headlight draws 4.5 A at 12 V (example). What is its resistance? (2) A starter cable test: the battery reads 12.4 V at its terminals while cranking, and 11.2 V at the starter's supply terminal. What is the drop? (3) The cable test across the earth strap reads 0.9 V while cranking. Which of (2) or (3) points to a bad connection, if your manual allows about 0.5 V (example) per cable?

Intermittent faults

An intermittent fault happens sometimes. Plan: (1) ask when it happens; (2) record the data while it happens (scan tool logging, or a helper who writes); (3) do wiggle tests on connectors and harnesses with the circuit running; (4) check for heat, water and vibration links; (5) change only one thing at a time and write it down. If the fault leaves no trace, say so honestly and offer to keep monitoring.

Written diagnosis report

Use: Complaint, Conditions, Findings (with numbers), Cause, Repair, Proof (retest), Advice. Give a copy to fleet customers. A good report reduces arguments and repeat visits.

Circuit and data diagnosis

  1. The instructor sets a faulty circuit (for example a poor earth or a sensor connector).
  2. Interview the "customer"; read codes and freeze-frame data.
  3. View live data; decide which values do not make sense.
  4. Draw the circuit from the diagram.
  5. Measure voltage at the load, and voltage drop across the supply and earth. Record each number.
  6. Find the fault, repair it and retest under the same conditions.
  7. Write the seven-line report and read it to a classmate.

Spot the sense

Pick one sensor value from a scan tool (with permission) and explain in two sentences what a normal reading should be and what a faulty reading would look like.

Check yourself: Unit 1

  1. What is voltage drop and where do you measure it?
  2. Why is a code not a diagnosis?
  3. Name two steps for an intermittent fault.
04

Unit 2 · Clutch, gearbox and driveline

Power must travel from the engine to the wheels. Where it is lost, noisy or jerky, the fault is in the clutch, gearbox or driveline.

Competency standard

Learning outcome Performance criteria — the trainee…
2.1 Explain the drivetrain names clutch, gearbox, driveshafts, propshaft and differential
2.2 Diagnose clutch faults slipping, dragging, judder and noise
2.3 Service gearbox and differential oil drains, fills to level and disposes safely
2.4 Check driveshafts and CV joints finds torn boots and clicking joints
2.5 Work as a team on heavy parts uses a transmission jack and supports safely

Range. Manual transmissions on light vehicles; automatic transmissions are checked externally (fluid, leaks, noise) only. Evidence. Diagnosis records; observation.

Tools and items for this unit

Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Earlier-level items are in the Level 1 and Level 2 appendices.

Item What it is and what it does Type or size (typical) Care or safety Also called
Clutch assembly Flywheel, pressure plate (a spring plate that presses), driven plate (clutch disc, the friction plate) and release (throw-out) bearing. Matched to the car Replace as a set. clutch kit
Clutch master and slave cylinder, clutch cable Hydraulic clutches use a master cylinder at the pedal and a slave cylinder at the gearbox; others use a cable. Hydraulic or cable Bleed like brakes. clutch slave
Gearbox oil and level, fill and drain plugs Oil in the gearbox. The level plug is usually also the fill hole; the drain plug is at the bottom; the breather lets air out. Grade as the manual says Use new washers. sump plug; transmission oil, gear oil
Differential and limited-slip differential The differential lets the wheels turn at different speeds in a corner. A limited-slip type needs special oil. Rear axle or inside the gearbox Use the oil the manual says. diff
Driveshaft, CV joint, boot, propshaft, universal joint and centre bearing Driveshafts carry power to wheels. A CV joint allows steering and movement. The boot holds grease. The propshaft carries power to the rear axle, and universal joints let it bend. Front-drive and rear-drive types Look for torn boots and play. constant-velocity joint; propeller shaft
Transmission jack A low, wheeled jack with a cradle made to lift and lower a gearbox. Rated capacity on the plate Strap the gearbox on. gearbox jack; lifting jack
Vehicle lift A two-post, four-post, scissor or pit set-up with mechanical locks and a capacity plate. Capacity plate on the lift Lower on the locks before work. car hoist, vehicle hoist
Engine support bar and workshop crane Supports an engine while parts are removed or lifts parts out. Rated capacity Inspect before use; trained operators only. no other common name found
Hydraulic press and bearing puller The press pushes parts on or off shafts. The puller pulls bearings off. Workshop press with a pressure gauge Guard and glasses. shop press

Parts and safety: Clutch assembly

Clutch assembly Clutch assembly with numbered parts 1 2 3 4 5 6 7 8
Clutch assembly. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Flywheel Carries the clutch and starts the engine Heavy; support when removing
2 Driven plate (clutch disc) Friction plate that grips the flywheel Keep oil off it
3 Pressure plate Spring plate that presses the disc Replace with the disc as a set
4 Diaphragm spring Releases and applies the pressure Do not dismantle
5 Release (throw-out) bearing Pushes the spring fingers Noise when the pedal is pressed
6 Input shaft Carries drive into the gearbox Align when refitting
7 Release fork Moves the release bearing Check for wear
8 Slave cylinder Hydraulic piston that moves the fork Bleed like brakes; leaks: refer

Safety protocol: Clutch assembly

Before. Qualified mechanic supervising; team of two or three. Support the vehicle on stands and the gearbox on a transmission jack. Wear glasses, gloves, dust mask.

While you work. Never blow clutch dust: wet-wipe it. Keep fingers away from the gap between engine and gearbox. One person gives instructions.

After. Torque bolts to the manual, refill and bleed, test the pedal, slip-test as the manual says. Record and report.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Parts and safety: Driveshaft with CV joints

Photograph of a drive shaft with a ribbed rubber bootA real driveshaft lying on a floor: a threaded end with a nut and a splined section on the left, a ribbed rubber boot in the middle, a clamp, and a plain shaft running to the right.12345
A real driveshaft with a ribbed rubber boot, removed from a car. Numbers on the picture match the table below. (Photo: BiH, public domain; Source: Photo CV Joint)

Photo credit: BiH, public domain.

No. Part What it does Safety rule
1 Axle nut Holds the shaft in the wheel hub Tighten to the manual's torque; fit a new locking part if the manual says so
2 Splined end Grooves that lock into the hub so the shaft turns the wheel Keep it clean; do not strike the splines
3 Rubber boot Keeps grease in and dirt out of the CV joint A torn boot or flung grease means the joint will wear out; report it
4 Boot clamp The band that holds the boot tight on the shaft Never pull on a clamp with a damaged boot; replace as a set
5 Shaft The steel bar that carries the turning force A bent shaft is never straightened; replace it
Driveshaft with CV joints Driveshaft with CV joints with numbered parts 1 2 3 4 5 6
Driveshaft with CV joints. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Inner CV joint Allows the shaft to move with the suspension Vibration under acceleration may point here
2 Shaft Carries power Check for bends
3 Outer CV joint Lets the wheel steer and move Clicking on tight turns often points here
4 Inner boot and clamp Holds grease in, dirt out Torn boot: replace early
5 Outer boot and clamp Same job at the wheel end Grease on the wheel arch shows a tear
6 Gearbox or differential end Where power enters Check seals for leaks

Safety protocol: Driveshaft with CV joints

Before. Vehicle on stands. Wear glasses, gloves. Turn the wheel by hand to find the noise.

While you work. Do not run the engine with a driveshaft removed. Keep hands from turning parts.

After. Clean grease, store parts clean, report torn boots in writing.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Safety protocol: heavy parts (gearbox)

Before. Qualified mechanic supervising; team of two or three; transmission jack; vehicle on stands; battery negative disconnected.

While you work. One person directs. Strap the gearbox on the jack. Keep fingers out of gaps. Never use a floor jack alone.

After. Torque to the manual, refill oil, dispose of oil correctly, record the job.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Ask a qualified expert. Gearboxes and engines are heavy and can fall. Brake and clutch dust is harmful; wet-wipe it, never blow it. Do not remove a gearbox without a transmission jack and a team under a qualified mechanic's supervision, and ask a GhIE-registered engineer about any lifting equipment you build or buy. Do not work on automatic transmission internals at this level.

The parts in plain words

  • Clutch: a friction plate pressed between the flywheel and a pressure plate. Press the pedal and the plate is released; let it up and it grips. A release (throw-out) bearing and a hydraulic cylinder or cable move it.
  • Gearbox (manual): gears of different sizes give different speeds and torque.
  • Driveshafts and CV joints: carry power to the front wheels and allow the wheels to steer and move; a rubber boot holds grease in.
  • Propshaft and differential (rear- or four-wheel drive): carry power to the rear axle and let the wheels turn at different speeds in a corner.

Clutch symptoms

Symptom Possible causes
Revs rise but speed does not (slip) Worn plate, oil on the plate, weak pressure plate, adjustment
Hard to get into gear, car creeps with the pedal down (drag) Hydraulic fault, air in the system, worn release parts
Judder on take-off Hot spots or oil on the plate, worn mounts
Noise when the pedal is pressed or released Release bearing, pilot bearing, release fork

Worn plates and air in a hydraulic clutch are common causes of slipping and a soft or low pedal; pumping the pedal is only a temporary fix and bleeding and leak checks are the cure. A quick slip check is to see if engine revs rise without the car speeding up.

Clutch checks

  1. Ask the owner about the pedal feel, noises, slipping and when it started.
  2. With the engine off, check the pedal: free play (cable) or a smooth firm feel (hydraulic). Look at the fluid level in the clutch reservoir.
  3. With the car in a safe, open place and the handbrake on, ask the instructor to show a slip test in a high gear at low speed, or follow the manual's test. Never do road tests that put people at risk.
  4. Look for leaks at the slave cylinder and the bell housing.
  5. Bleed a hydraulic clutch with the same care as brakes (see Level 2), using the fluid in the manual and keeping the reservoir full.
  6. Write the finding and advice. Replacement of the clutch is a team job with a qualified mechanic.

Gearbox and differential oil

Use the oil grade in the manual. Check the level at the level plug, which is usually also the fill hole: oil should just reach the hole. Replace the sealing washers. Drain used oil into a labelled container. A burnt smell or metal in the oil is a warning: write it down and refer.

Driveshafts and CV joints

Torn boots let grease out and dirt in; replace them early. A clicking noise on tight turns often points to a worn outer CV joint (author's note from general practice, not from a cited source); a vibration under acceleration may point to an inner joint or a bent shaft. Confirm with a careful inspection on stands.

Heavy parts safely

Use a transmission jack or a lift made for the job, never a floor jack alone. Work in a team of two or three, with one person giving instructions. Support the engine if the manual says. Keep fingers out of the gap between the gearbox and the engine. Keep brake and clutch dust off your face, and wipe up wet.

Gear ratios

A first gear ratio is 3.6 : 1 and the final drive is 4.1 : 1 (examples). (1) What is the overall ratio in first? (2) If the engine turns at 3,000 rpm, how fast do the wheels turn in revolutions per minute?

Noise diary

Ask a driver to describe noises they hear from the clutch, gearbox or driveshafts. Write the sound, when it happens and what you think it is.

Check yourself: Unit 2

  1. Why must you never blow brake or clutch dust off with your mouth or compressed air?
  2. What is a quick sign of clutch slip?
  3. Where do you set the gearbox oil level?
05

Unit 3 · Modern vehicles: injection, diesel, hybrid and electric

Modern cars are computers on wheels. Know what you can safely do, and what you must refer.

Competency standard

Learning outcome Performance criteria — the trainee…
3.1 Explain engine management names the main sensors, the ECU and injectors
3.2 Explain diesel injection describes common rail and the pressure hazard
3.3 Know hybrid and electric limits recognises the high-voltage system and keeps away
3.4 Manage keys, immobilisers and data ethically explains legal and ethical limits
3.5 Plan training names a route to further training

Range. Awareness and safe limits; no work on high-voltage systems. Evidence. Oral questions; diagrams.

Tools and items for this unit

Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Earlier-level items are in the Level 1 and Level 2 appendices.

Item What it is and what it does Type or size (typical) Care or safety Also called
Sensors: crankshaft, camshaft, air flow, manifold pressure, coolant temperature, throttle position, oxygen, knock Crankshaft and camshaft sensors tell the ECU position and speed; the air flow sensor measures air in; the manifold pressure sensor measures vacuum; the temperature sensor reads coolant; the throttle sensor reads pedal; the oxygen sensor reads exhaust oxygen; the knock sensor listens for knock. On the engine, intake or exhaust Test as the manual shows; do not guess. antifreeze; lambda sensor, O2 sensor
Injector, high-pressure pump and fuel rail The pump raises fuel pressure, the rail stores it, and the injectors spray it. Diesel common-rail pressures are very high Never loosen a line; see the pressure hazard. fuel injector
Glow plug A heater in a diesel cylinder that helps a cold start. Thin heater pencil Hot; handle when cold. no other common name found
Turbocharger and intercooler The turbo uses exhaust to compress intake air. The intercooler cools that air. On the exhaust side Very hot; look for oil leaks. turbo; charge-air cooler
Diesel particulate filter and catalytic converter The DPF traps soot. The catalytic converter changes exhaust gases to cleaner ones. In the exhaust Do not remove: emission tampering may be an offence (not verified); ask the EPA. cat, catalyst
EGR valve Lets some exhaust back into the intake to lower combustion heat. Between the exhaust and intake Look and report. no other common name found
High-voltage battery, inverter, orange cable, service disconnect The traction battery stores high-voltage power; the inverter converts it; orange cables carry it; the service disconnect cuts it, for trained people only. Hybrid and electric vehicles Do not touch. traction battery; service plug
Key, immobiliser and transponder chip The key carries a chip. The immobiliser stops the engine if the code is wrong. Coded chip Only program for the proven owner. immobilizer

Parts and safety: Diesel common-rail fuel system (overview)

Diesel common-rail fuel system (overview) Diesel common-rail fuel system (overview) with numbered parts 1 2 3 4 5 6 7 8
Diesel common-rail fuel system (overview). Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Fuel tank Stores fuel No flames; watch for water
2 Fuel filter and water separator Cleans fuel; collects water Drain only as the manual says
3 High-pressure pump Raises the fuel to very high pressure Never loosen a line; pressure remains after stop
4 Pressure control valve Controls the rail pressure Refer
5 Rail Stores high-pressure fuel for all injectors Never crack a line to bleed
6 Injectors Spray fuel into the cylinders A fluid jet can pierce the skin
7 Engine control unit (ECU) Controls pump and injectors Do not probe
8 Rail pressure sensor Reports pressure to the ECU Refer faults

Safety protocol: Diesel common-rail fuel system (overview)

Before. Awareness only at this level. Do not work on the high-pressure side. Engine off for a long time and the maker's depressurise steps by a trained technician.

While you work. Do not loosen lines or run the engine with fittings open. Keep face and hands away. No naked flames.

After. Report the fault in writing and refer to a trained diesel technician.

Emergency. A pinprick-looking injection injury is a medical emergency: call 112 and go to hospital at once. Fire: call 112.

Ask a qualified expert. Fuel injection systems and high-voltage batteries can seriously injure or kill. Do not loosen high-pressure fuel lines, open airbags or touch orange high-voltage cables. Ask a qualified mechanic or a GhIE-registered engineer, and use only people trained by the maker for hybrid and electric work. Ask a qualified lawyer about key programming and anti-theft systems.

Engine management in plain words

The engine control unit (ECU) is a small computer. Sensors tell it what is happening: air flow or manifold pressure, coolant temperature, throttle position, crankshaft and camshaft position, oxygen in the exhaust, knock. It then controls injectors, ignition and other parts so the engine runs cleanly. If a sensor fails, the ECU often uses a default value and stores a code.

Sensor What it tells the ECU A fault may cause
Crankshaft position Engine speed and position No start, stalling
Air flow or manifold pressure How much air enters Rough idle, poor power
Coolant temperature Engine temperature Hard start, fan not working
Oxygen sensor Whether the mixture is rich or lean High fuel use, emission code
Throttle position How far the pedal is pressed Hesitation

Diesel common-rail injection: the pressure hazard

In a common-rail diesel engine a high-pressure pump fills a rail with fuel at very high pressure, and the ECU opens each injector. One maker's manual warns not to work on the injection system with the engine running or soon after shutting off, because the pump, rail, injectors and pipes stay under high pressure even after the engine stops. A safety group warns that high-pressure fluid can pierce the skin and look like a small pinprick while causing serious injury, so it is a medical emergency. Never crack a high-pressure line to bleed or to check for fuel. At this level you check filters, water traps and low-pressure systems per the manual and refer the rest. If a person is hurt, call 112 and get them to a hospital at once.

Turbochargers and emissions: what you can check

Check for oil leaks around the turbo, loose pipes, a blocked air filter and the correct oil. Diesel particulate filters and catalytic converters are costly; do not cut them off or sell "deletes". Emission tampering may be an offence; ask the EPA or a qualified lawyer (not verified).

Hybrid and electric vehicles

Hybrid and electric vehicles have a high-voltage battery and cables, usually coloured orange. Extra skills and training are needed for safe work, and only competent trained people should work on them. In Ghana, training of artisans for electric vehicles has begun at Suame Magazine in Kumasi, according to news reports. For your own safety at Level 3:

  • Treat any orange cable as live; do not touch, cut or unplug it
  • Do not open the high-voltage battery or inverter
  • Put a warning sign on the vehicle and keep the key away
  • Refer the job to a trained, maker-approved technician
  • In a crash or a fire, stay back and call 112 and the fire service; tell them it is a hybrid or electric vehicle

Ask the maker's dealer or a trained technician for the emergency guide of a specific vehicle.

Keys, immobilisers and data

Modern keys carry a coded chip. Programming keys should be done only for the owner, who can show papers and identity. Helping a thief clear an immobiliser is a crime and could harm your name. Do not copy or sell customers' vehicle data; keep their numbers and details private.

Know your limits

  1. For a diesel and a hybrid vehicle (pictures, video or a demonstration), list the parts you may check and the parts you must refer.
  2. Draw a simple diagram of an engine management system with five sensors.
  3. Write a short message to a customer who asks you to "fix" a hybrid battery: say what you can do, what you cannot do, and who they should ask.
  4. List two ways to build skills for modern vehicles (a maker's training, a technical college, a trained mentor).

Training route

Find out where in your region you can get training on modern engine management or hybrid vehicles, and what it costs. Write the place, the course and the price (mark prices you were told as "reported").

Check yourself: Unit 3

  1. What colour are high-voltage cables on hybrids and electric vehicles?
  2. Why must you never loosen a common-rail diesel line to check for fuel?
  3. What does the ECU do?
06

Unit 4 · Run a safe, quality workshop

A workshop is a team. You are responsible for their safety, for the quality of the work and for the customers' trust.

Competency standard

Learning outcome Performance criteria — the trainee…
4.1 Manage lifting and equipment inspects lifts and stands, keeps locks engaged and logs inspections
4.2 Supervise and train gives clear instructions, trains apprentices and records training
4.3 Control quality uses job cards, second checks and a final inspection
4.4 Manage fire, spills and waste keeps extinguishers, spill kits and waste containers
4.5 Handle complaints and customer care records complaints and follows up

Range. A small workshop of two to six people. Evidence. Risk assessment; training record; inspection logs.

Tools and items for this unit

Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Earlier-level items are in the Level 1 and Level 2 appendices.

Item What it is and what it does Type or size (typical) Care or safety Also called
Lifting chain, hoist and lifting sling Chains and slings take the load from a hoist. A hoist lifts heavy parts. Rated Safe Working Load (SWL) marked on a tag Inspect and log; never exceed the rated load. chain block
Safety signs and hazard tape Signs warn of dangers; tape marks areas. Standard colours and symbols Place at the hazard. no other common name found
Fire blanket and spill kit The fire blanket smothers a small fire. The spill kit holds sand, pads, a broom and a container. Wall-mounted pack Check monthly. no other common name found
Waste station and oil drum with bund A bund is a tray or wall that holds a spill from a drum. Labelled containers Keep sealed. spill tray
Tool board and calibration log A board with an outline for each tool, and a record of when measuring tools were last checked. Wall board; one log book Count at close. no other common name found
Air compressor, air line and impact wrench Compressed air for tools; an impact wrench loosens nuts with hammer action. Workshop compressor with a safety valve Never blow dust at people. air gun, rattle gun

Parts and safety: Two-post vehicle lift

Two-post vehicle lift Two-post vehicle lift with numbered parts 1 2 3 4 5 6 7 8
Two-post vehicle lift. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Column Carries the carriage up Anchor bolts checked by a qualified person
2 Arm and lifting pad Contacts the car's lift points Use the manual's lift points
3 Arm restraint Stops the arm swinging Check it engages
4 Mechanical lock Holds the lift up if the hydraulics fail Lower onto the locks before going under
5 Capacity plate Shows the maximum load Never exceed it
6 Overhead beam or hydraulic unit Powers the lift Inspect hoses; report leaks
7 Base plate Fixes the lift to the floor Floor must be sound
8 Second column Other side of the lift Both sides rise together

Safety protocol: Two-post vehicle lift

Before. Trained operators only. Check the capacity plate, locks, arms, hoses and the floor. Clear the area of people and tools. Wear boots and glasses.

While you work. Position the arms at the lift points. Raise slightly and check stability. Lower onto the mechanical locks before anyone goes under. Never disable the locks.

After. Lower fully, swing the arms clear, switch off the power, log faults and any inspection.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Ask a qualified expert. Workplace law, fire safety and lifting equipment need professionals. Ask the Factories Inspectorate or the Labour Department about your duties; ask the Ghana National Fire Service about fire safety; ask a GhIE-registered engineer about lifts, hoists, the building and the electrical installation; use a licensed electrician for workshop wiring; ask the EPA about waste. This is general information, not legal advice.

Lifting equipment

  • Lower a lifted vehicle onto the mechanical locks before anyone goes under it; locks must engage and hold. Never disable locks with ropes or tools.
  • Check the capacity plate. Do not overload a lift.
  • Have lifts and hoists inspected regularly by a qualified lift inspector; the American lift standard asks for at least yearly inspection by a qualified inspector, but no Ghana rule was found, so ask a GhIE-registered engineer.
  • Keep a log: date, equipment, condition, who inspected, action.

Safety law and supervision

The Factories, Offices and Shops Act 1970 (Act 328) covers workplaces such as factories and shops; its provisions include training and supervision and the fencing of dangerous machinery, and the Factories Inspectorate inspects workplaces. The section numbers were not verified. Ask the Factories Inspectorate what applies to your garage. As a supervisor you must:

  1. Brief the team before each risky job (what, who, how, what if).
  2. Make sure people are trained for what they do; keep a training record.
  3. Check PPE is worn and in good condition.
  4. Stop any job that is unsafe, and say so loudly.
  5. Never put apprentices on brake, steering or fuel pressure work alone.

Quality system

  • Job card completed for every vehicle, signed by the mechanic.
  • Second check by another person for safety items: wheels torqued, brakes, steering, fluid levels.
  • Final inspection and road test done with a checklist.
  • Records kept for each job: customer, number plate, work, parts, hours, cost.
  • Callbacks logged: any job that returns for the same fault, with the cause.
  • Tool control: tool board with outlines; count at close.

Fire, spills and waste

  • Extinguishers placed near the exit and the fuel area, checked yearly (ask the Fire Service).
  • Spill kit: sand, absorbent pads, a broom, a container.
  • A waste station with labelled containers for used oil, filters, coolant, brake fluid, batteries, tyres and general rubbish.
  • A waste log: what, how much, date, who collected. The EPA has warned that garage waste pollutes; ask the EPA for the current rules.

Customer care and complaints

Record every complaint with the date and the vehicle. Respond the same day, even if only to say when you will look. Fix your mistake at your cost if it is your fault. Thank the customer for telling you.

Roadworthiness and inspection duty

Only a designated private vehicle testing station inspects for a roadworthiness certificate with the vehicle and its registration certificate. DVLA closed six testing stations in 2026 for issuing reports without proper inspection. Never sell or forge a sticker. If a customer asks you to "make it pass", say no.

Risk score

Score each hazard for likelihood and severity, each 1 to 5 (example). Multiply for risk. (a) Lift locks not engaged: likelihood 3, severity 5. (b) Oil spill on the floor: likelihood 4, severity 2. (c) Battery charging near a flame: likelihood 2, severity 5. (d) Unlabelled coolant bottle: likelihood 3, severity 4. (1) Calculate each. (2) Rank them. (3) Which would you fix first?

Workshop safety audit

  1. Walk the training workshop with a checklist: lifts and stands, extinguishers, spill kit, waste containers, PPE, lighting, exits, tool board.
  2. Score each hazard with the risk table.
  3. Write an action list with who, what and by when.
  4. Write a one-page toolbox talk on one hazard and give it to a small group.
  5. Record the results in your logbook.

Waste route

Ask at your local EPA office or a garage owner where used oil and batteries go. Write the answer and mark anything you could not confirm "not verified".

Check yourself: Unit 4

  1. What must happen before anyone goes under a lifted vehicle on a lift?
  2. Why keep a callback log?
  3. Name two items you would keep at the waste station.
07

Unit 5 · Establish your garage

A garage that is registered, insured and properly permitted can bid for fleets and be trusted with credit. A garage that is not can be closed on any day.

Competency standard

Learning outcome Performance criteria — the trainee…
5.1 Choose a legal form compares business types and registers one
5.2 Meet tax and permit duties lists tax, VAT, Assembly and waste duties
5.3 Budget the start-up lists tools, premises, stock and working capital with example costs
5.4 Employ fairly applies SSNIT, PAYE and Labour Act basics
5.5 Write a one-page plan and pitch explains location, finance, risk and marketing

Range. Own business plan. Evidence. Registration checklist with costs; start-up budget; payroll sheet; one-page plan.

Tools and items for this unit

Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Earlier-level items are in the Level 1 and Level 2 appendices.

Item What it is and what it does Type or size (typical) Care or safety Also called
Business name certificate and TIN Papers that show your business name is registered and your tax number. From ORC and GRA Keep copies. tax identification number
Business operating permit A permit from the Assembly to run the garage. Yearly Ask the Assembly for the fee. no other common name found
Insurance policy A contract that pays if there is loss or damage. Fire, theft and liability types Ask a licensed adviser. no other common name found
Lease agreement A paper that sets the rent and rules for your site. Written Ask a lawyer. no other common name found

Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer before you act on any legal, licence or registration matter. For tax, VAT, PAYE and SSNIT, check with GRA or a qualified accountant before you act. For loans and insurance, ask your bank, the National Insurance Commission or a licensed financial adviser. For workshop buildings, lifts and wiring, ask a GhIE-registered engineer and a licensed electrician.

Choose a legal form

Type ORC fee (2026) Notes
Business name (sole proprietor) GH¢130; GH¢70 renewal Most garages start here; you are personally responsible for debts
Partnership GH¢270; GH¢100 renewal 2 to 20 partners; written agreement
Company limited by shares GH¢585 plus a capital duty At least two directors and a secretary; yearly returns; shields your own assets; check the capital duty rate
Company limited by guarantee GH¢490 For non-profit training garages

Companies file annual returns; the fee is GH¢175 a year and late filing carries a penalty. Cooperatives are not registered at the ORC, and the route for registering one was not verified.

Tax and permits

  • Your Ghana Card number is your tax number. Companies get a TIN after ORC registration.
  • Sole traders with business income only, and not VAT-registered, may use the Modified Taxation Scheme: fixed instalments up to GH¢20,000 turnover, and 3% of turnover from GH¢20,001 to 750,000 under the 2026 amendment. Partners and owners of several outlets are excluded.
  • Companies pay 25% tax; 18.5% for manufacturers in a regional capital such as Takoradi (not for garages). Provisional tax is paid each quarter.
  • VAT: from 2026 it is 15% plus 2.5% and 2.5% levies, 20% in all. For goods the registration threshold is GH¢750,000; for services there is no turnover threshold and you register within 30 days of starting. A garage sells services and parts: ask GRA or an accountant which rule applies to you.
  • Withholding tax: customers may withhold part of your payments; keep the certificates.
  • Assembly permit: apply to the Sekondi-Takoradi Metropolitan Assembly at its permit portal. The garage fee was not verified; ask STMA.
  • Waste and environment: ask the EPA what a garage needs.
  • Fire: ask the Ghana National Fire Service for a fire safety check (not verified).
  • Insurance: use only insurers licensed by the National Insurance Commission. Compulsory covers for a garage were not verified; ask the NIC.

Premises and start-up budget (all prices are examples)

Item Example cost (GH¢)
Rent advance (container or shed), 6 months at 1,200 7,200
Basic tool set, torque wrench, jacks, stands 9,000
Scan tool and multimeters 3,500
Compressor, extension lights, bench, vice 4,000
Opening stock: oil, filters, bulbs, fuses 6,000
Signage, uniforms, registration and permits 1,500
Safety: extinguishers, first-aid, spill kit 1,000
Working capital: first three months of costs 9,000
Total 41,200

Add the figures: 7,200 + 9,000 + 3,500 + 4,000 + 6,000 + 1,500 + 1,000 + 9,000 = 41,200. Use your own local quotes to replace these example numbers.

Finance

Options: your savings, a susu or VSLA group, a microfinance loan, a bank loan, or support programmes. The Ghana Enterprises Agency has Business Advisory Centres in Takoradi and nearby districts. The 2026 Budget names programmes including the National Apprenticeship Programme and the Women's Development Bank; details and eligibility were not verified. The Bank of Ghana policy rate was 14%, so loans are costly; borrow only what the garage can repay. Ask your bank or a licensed financial adviser.

Employing mechanics and apprentices

  • Minimum pay is GH¢21.77 a day for 2026.
  • SSNIT: worker 5.5% plus employer 13%, paid by the 14th of the next month; register workers when hired.
  • PAYE: the first GH¢588 a month is tax-free; pay by the 15th.
  • Written contract for six months or more; 15 working days of paid leave.
  • Apprentices: register them with the Assembly if required; STMA says master artisans must register their trainees.

Accessibility

The Persons with Disability Act 2006 bans job discrimination. Diagnostics, scan data, estimates, parts, bookkeeping and customer service are desk or bench work that suit wheelchair users. Deaf mechanics need visual signals for lifts and hot work and written job cards. The Assemblies' disability fund now supports skills and assistive devices.

Register and budget

  1. Choose a legal form and explain why.
  2. Make a registration and permit checklist with the cost of each step (mark unverified fees).
  3. Replace the example start-up budget with local quotes.
  4. Work out one month's payroll for two mechanics (example wages of your choice).
  5. Write a one-page plan: location, services, prices, first customers, finance, risks.

Payroll

Example: an employee earns GH¢2,400 basic a month. (1) Employee SSNIT at 5.5%? (2) Employer SSNIT at 13%? (3) Taxable pay after SSNIT? (4) PAYE using the bands below.

Permit visit

Visit the STMA permit office, or ask through its permit portal,, and write what documents a garage needs and what it costs. Mark anything you could not confirm "not verified".

Check yourself: Unit 5

  1. Name two types of business you can register at the ORC and their fees.
  2. Who may use the Modified Taxation Scheme?
  3. What is the employer's SSNIT rate?
08

Unit 6 · Bookkeeping and accounting for a garage

Every job uses parts, hours and tools. Cost each job, or you will not know which work pays.

Competency standard

Learning outcome Performance criteria — the trainee…
6.1 Keep daily books keeps cash book, MoMo/bank, job cards, purchases and stock records
6.2 Produce statements prepares a monthly profit and loss and balance sheet
6.3 Price and break even works out hourly rates, margin, mark-up and break-even
6.4 Control cash and tax records reconciles MoMo and bank, forecasts cash and keeps records

Range. One month of real or example jobs. Evidence. Books; statements; reconciliation; forecast.

Tools and items for this unit

Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Earlier-level items are in the Level 1 and Level 2 appendices.

Item What it is and what it does Type or size (typical) Care or safety Also called
Cash book and ledger The cash book lists money in and out; the ledger groups the entries by account. Hard-cover book or sheet Update every day. no other common name found
Stock card and parts list A card for each part kept in stock showing in, out and balance. One card per part Count each month. no other common name found
Invoice and receipt The invoice asks for payment; the receipt proves it. Numbered duplicate books Never reuse a number. bill
MoMo and bank statements Records of mobile-money and bank movements used to reconcile with the books. Monthly Match every line. no other common name found
Accounting software A program that keeps books, such as a spreadsheet or an app. Prices not verified Back up the file. no other common name found

Ask a qualified expert. This is general information about money, tax and records, not tax or legal advice. Check with GRA or a qualified accountant before you act on tax, VAT, PAYE or SSNIT, and ask a licensed financial adviser or your bank about loans.

The records

Record What it shows
Job cards Parts, hours, deposits and balance for each vehicle
Purchases book Parts, oil, consumables bought, from whom, price
Stock sheet Parts and consumables in store, counted each month
Cash book and MoMo book Every cedi in and out
Debtors book Who owes you and for how long (fleet customers)
Asset register Tools and equipment, cost, date, depreciation

Keep records in Ghana for at least 6 years.

Assets = liabilities + owner's equity. Depreciation (straight-line) = (cost - end value) / years of use.

Pricing, margin and mark-up

  • Mark-up is profit as a percent of cost. Margin is profit as a percent of price. A 25% mark-up is a 20% margin.
  • Hourly labour rate: monthly costs (including your pay) divided by billable hours. If you are only busy for part of the day, divide by the billable hours, not all hours.
  • Break-even: fixed costs divided by the average gross profit per job tells you how many jobs you need before you earn anything.

Worked example (all figures are examples)

Kwesi's garage, August

  • Kwesi puts in GH¢30,000.
  • He buys tools and a scan tool for GH¢9,000 (5 years, no end value).
  • Labour income: GH¢14,000, all in cash.
  • Parts sold: GH¢16,000, of which GH¢3,000 is owed by a taxi owner who pays next month.
  • Parts bought: GH¢13,500, all paid in cash. Parts left in stock at month-end: GH¢1,500 (no stock at the start).
  • Rent GH¢1,200; power and water GH¢600; one mechanic GH¢2,400; consumables GH¢500; transport GH¢400; waste collection GH¢150.
  • Kwesi takes GH¢2,000 for himself (drawings).

Work out: (1) cash at the end of August; (2) net profit; (3) the balance sheet; (4) the gross profit and margin on parts; (5) the number of jobs needed to break even if the average gross profit per job is GH¢450.

Reconciliation and the month-end routine

  1. Count the cash and compare with the cash book.
  2. Match MoMo and bank statements to the books. Note any difference.
  3. Count the parts in stock and update the stock sheet.
  4. Chase debtors.
  5. Prepare the profit and loss and the balance sheet.
  6. Pay the tax and SSNIT on the dates.
  7. Sit down with the numbers: what paid, what did not?

Sample cash book page (example)

Date Details In (GH¢) Out (GH¢) Balance (GH¢)
1 Aug Capital 30,000 30,000
2 Aug Tools and scan tool 9,000 21,000
5 Aug Parts bought 4,000 17,000
8 Aug Service jobs (cash) 2,500 19,500
10 Aug Rent 1,200 18,300

Software and the calendar

Use a spreadsheet, or a free plan such as Zoho Books or Wave.

When What
14th SSNIT
15th PAYE and withholding tax
Last working day VAT (if registered)
Quarterly Provisional tax for companies
Within 4 months of year-end Annual income tax return
By 31 March Assembly permit

Month-end close

  1. Keep job cards, cash book and a stock sheet for one month (real or example).
  2. Reconcile MoMo and bank.
  3. Prepare a profit and loss and a balance sheet.
  4. Work out your hourly labour rate and break-even jobs.
  5. Forecast cash for three months.

Parts prices

Collect prices of five common parts (oil, filter, pads, plugs, battery) from two Takoradi dealers. Write the date and the shop. Mark prices you could not confirm as "not verified".

Check yourself: Unit 6

  1. What is the accounting equation?
  2. What is the difference between mark-up and margin?
  3. How long must you keep records?
09

Unit 7 · Grow and sustain the business

Grow on trusted work, documented quality and a good name. Do not grow faster than your cash.

Competency standard

Learning outcome Performance criteria — the trainee…
7.1 Find finance and markets identifies finance, support and markets
7.2 Lead people and quality develops mechanics and keeps quality records
7.3 Plan and pitch presents a one-page plan with a 12-month cash forecast

Range. Own business plan. Evidence. Business plan; cash forecast; pitch.

Tools and items for this unit

Each item is named and defined. Sizes are typical; the maker's manual rules. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture. Earlier-level items are in the Level 1 and Level 2 appendices.

Item What it is and what it does Type or size (typical) Care or safety Also called
Business plan and 12-month cash-flow forecast A plan that shows what you will sell and how cash moves each month. One page plus a table Update every quarter. no other common name found
Tender document A request that asks garages to quote for fleet or contract work. From a company or agency Read the terms carefully. bid document
Fleet service contract An agreement to service a customer's vehicles for a fixed price. Written Ask a lawyer before signing. no other common name found

Ask a qualified expert. This is general information, not legal or financial advice. Ask a qualified lawyer before you act on any contract, tender or licence matter, and check with GRA or a qualified accountant on tax. Ask your bank or a licensed financial adviser about loans and guarantees, and a GhIE-registered engineer about workshop expansion, lifts and buildings.

Finance and support

  • The Ghana Enterprises Agency has Business Advisory Centres in Takoradi and nearby districts.
  • GIRSAL gives guarantees for agricultural loans; this may help a garage serving farms, but check eligibility.
  • Ghana EXIM supports SMEs and has a Takoradi office.
  • The Bank of Ghana policy rate was 14%.
  • For any loan, bring: your registration, TIN, cash book summary, a profit and loss, a cash forecast and a quote for the item you will buy.

Markets

  • Fleets: taxis, minibuses, school buses, farm pickups and company vehicles. Offer a monthly service contract with a price list.
  • Second-hand vehicle inspection: a written look-and-report for buyers.
  • Tenders and supply: offices and institutions buy repair services; they ask for registration, a TIN, tax clearance and references (not verified for each buyer). Ask the buyer and ask GRA what clearance you need.
  • Partnerships: work with a tyre shop, a battery seller, a spare-parts dealer or a body shop; agree referral fees in writing.

Location settings that give good returns

  • Near taxi, trotro and minibus ranks, and the Kokompe garage cluster
  • On the road to the port, industrial area or a fuel station with fleet traffic
  • With room for lifts, safe parking, a waste station and good drainage
  • With reliable power (and a safe generator area) and water
  • Close to parts suppliers

Business ideas and ingenuity

  • Fleet service contracts with a monthly report
  • Diagnostics-first package with a written report
  • Mobile battery, tyre and brake safety checks for fleets
  • Training apprentices and charging a fair fee, with a written agreement
  • A small shop for oil, filters, wipers and bulbs
  • Referral partnership with a hybrid and electric specialist (do not do the work yourself)

Lead people and quality

Pay on time. Train your people and write down what they can do. Give each a clear job and a safe place to ask questions. Reward quality and honesty. Keep a callback log and fix the cause, not the person. Plan who will run the garage if you are away or ill (succession). Treat customers' money and data with respect.

Pricing strategy and scaling

Price by cost and value. A cheap price that loses money kills the business. Add a second bay or mechanic only when your jobs are booked for weeks and your cash can pay the extra costs for three months. Open a second site only when the first runs well without you.

Market yourself

  • Show your skills with a portfolio, certificates and customer testimonials.
  • Use WhatsApp Business: catalogue, quick replies, labels and reminders for the next service.
  • Google Business Profile: hours, photos and reviews.
  • Give each customer a service sticker with the next service date.
  • Sponsor a driver's association event; offer a free safety check day.

Capstone

Present to a panel: a one-page business plan and a 12-month cash forecast. Include your start-up budget (with local quotes), your location, your permits, your prices, your staff, your waste plan and your risks.

Cash forecast (first three months, example)

Opening cash GH¢10,000. Month 1: cash in 18,000; cash out 15,500. Month 2: in 22,000; out 17,000. Month 3: in 20,000; out 21,500 (includes GH¢5,000 for a new lift). Work out the closing cash each month. In which month is the risk?

Pitch

  1. Write a one-page plan.
  2. Build a 12-month cash forecast on a spreadsheet.
  3. Pitch to a panel for ten minutes.
  4. Answer three questions about risk, permits and waste.

Local fleets

List five fleets in your area (taxi unions, school buses, farms) and how you would reach each one.

Check yourself: Unit 7

  1. Name two markets for a garage besides walk-in customers.
  2. When should you add a second mechanic or bay?
  3. What goes in a one-page business plan?
10

Glossary

Term Meaning
CV joint Constant-velocity joint on a driveshaft that lets the wheel steer and move
Common rail A diesel system where one high-pressure rail feeds all the injectors
ECU Engine control unit, the engine's computer
Intermittent fault A fault that comes and goes
Live data Sensor values shown now by a scan tool
Margin Profit as a percent of the selling price
Mark-up Profit as a percent of the cost
Parasitic drain Current drawn when the car is off
Straight-line depreciation Spreading a tool's cost evenly over its life
Voltage drop Voltage lost in a wire or connection
11

Logbook

Copy these pages into an exercise book. Your logbook is part of your assessment evidence.

  • Unit 1: circuit and data diagnosis; written reports
  • Unit 2: clutch checks; gearbox oil record; noise diary
  • Unit 3: limits list; engine management diagram; training route
  • Unit 4: safety audit; risk table; toolbox talk; waste route
  • Unit 5: registration checklist; start-up budget; payroll
  • Unit 6: books; statements; break-even; parts price list
  • Unit 7: one-page plan; 12-month forecast; pitch notes
  • Every homework, dated
12

Self-check quiz

  1. What is voltage drop and where is it measured?
  2. Why is a trouble code not a diagnosis?
  3. What is a quick sign of clutch slip?
  4. Why must you never blow brake or clutch dust off?
  5. Why must you never loosen a common-rail diesel line to check for fuel?
  6. What colour are hybrid and electric high-voltage cables, and what must you do about them?
  7. What must be engaged before anyone goes under a lifted vehicle on a lift?
  8. What is the cost to register a business name in 2026?
  9. What is the employer's SSNIT rate?
  10. What is the accounting equation?
  11. What is the difference between margin and mark-up?
  12. For how long must you keep business records?
13

Appendix A · Advanced diagnostic charts

Each chart says what to measure and what the reading means. Numbers are typical; the workshop manual rules. Test one thing at a time and write it down.

Ask a qualified expert. Electrical, fuel-pressure, airbag, high-voltage and diesel injection faults can injure or kill. Work only on 12-volt circuits as shown. Ask a qualified mechanic, an auto electrician or a GhIE-registered engineer for anything beyond that.

A1 · Intermittent fault

Step Action Meaning
1 Ask when: hot, cold, wet, bumps, load Narrows the condition
2 Log live data while it happens Shows which signal drops
3 Wiggle connectors and harness with the circuit running The signal jumps when you touch the fault
4 Check heat, water, vibration links Water in connectors, loose clips
5 Change one thing at a time So you know what fixed it
6 Cannot find it Say so; offer monitoring

A2 · Electrical circuit (no operation)

Step Test Meaning
1 Fuse good? (volts at both sides) Blown fuse: find the short; do not fit a bigger fuse
2 Voltage at the load Zero: supply fault
3 Voltage drop across the supply Large drop: bad joint or cable
4 Voltage drop across the earth Large drop: bad earth
5 Load itself Replace only after steps 1 to 4

A3 · Network (CAN idea)

Modern cars link their computers by a data network. A U-code means modules are not talking. Check battery voltage and earths first, because low voltage causes many network codes; refer network wiring faults to a qualified auto electrician.

A4 · Injection and no-power (petrol)

Step Test
1 Air filter and intake leaks
2 Fuel trims on a warm idle (Appendix B)
3 Misfire counters
4 Fuel quality; filter date
5 Exhaust restriction (refer)

A5 · Diesel starting

Step Test
1 Battery and cranking speed
2 Fuel in tank, water in the fuel filter (drain per manual)
3 Glow plug light and time, in cold weather
4 Bleeding an older-type system; common-rail systems: never loosen high-pressure lines
5 Codes; refer high-pressure faults

A6 · Turbo, DPF and driveline noise

Area Check
Turbo Oil leaks, loose pipes, dirty air filter, correct oil
DPF Warning light; do not remove; refer
Driveline clicking on tight turns Outer CV joint (author's note, general practice)
Vibration on acceleration Inner joint or bent shaft
Whine in gear Gearbox or differential; check oil level
14

Appendix B · Scan-data guide

Use live data to ask: does this value make sense? Values below are typical for a warm petrol engine; not verified here for any vehicle. Use the manual and compare with a known-good car of the same type.

Ask a qualified expert. Do not condemn a part on one reading. Ask a qualified mechanic or auto electrician before replacing sensors or the ECU.

Parameter (PID) Typical idea What a wrong value suggests
Coolant temperature A warm engine settles near the thermostat's opening temperature Cold engine reading very hot: sensor or wiring fault
Short-term fuel trim Near zero, swinging up and down A large steady plus: lean; a large steady minus: rich
Long-term fuel trim Near zero Same, over time
Mass air flow Rises smoothly with revs Flat or jumpy: sensor, intake leak
Manifold pressure Low at idle, rises with throttle High at idle: leak or a valve fault
Throttle position Low when closed, rises smoothly Jumps: worn sensor
Oxygen sensor (narrow-band) Switches up and down quickly Stuck: sensor, mixture or exhaust leak

A rule many technicians use is that trims within about plus or minus 10 percent are acceptable (typical; not verified). Percent means how much the computer is adding or taking away.

15

Appendix C · OBD full guide

Ask a qualified expert. Emission-system codes and tampering have legal consequences. Ask the EPA or a qualified lawyer, and a qualified mechanic for repairs.

Item Note
Code format Letter plus four characters. A seven-character format is mentioned by some sources; not verified
Second character 0 is generic. Other digits differ between sources; check SAE J2012 and ISO 15031-6
Groups P00xx to P02xx fuel and air; P03xx ignition and misfire; P04xx emissions; P05xx idle and speed; P06xx computer; P07xx to P09xx transmission
Modes (services) Current data, freeze frame, stored codes, clear codes, pending codes and vehicle information are the usual ones; the standard is SAE J1979 (international; not verified here)
Readiness monitors Self-tests; clearing resets them, so a car may not pass an emissions test straight after
Pending versus confirmed Seen once versus seen again
Maker codes Differ by make; many cars sold in Ghana are imports, so generic codes match but maker codes do not
Rule A code points to a system: confirm with a test
16

Appendix D · Electrical reference

Ask a qualified expert. Car electrics can start fires. Work on 12-volt only, with the battery negative disconnected where the manual says. Ask a qualified auto electrician or licensed electrician for anything more.

Card Content
Ohm's law V = I x R; I = V / R; R = V / I
Power P = V x I
Worked 12 V and 4.5 A: R = 2.67 ohm; P = 54 W
Voltage drop 12.4 V at the battery, 11.2 V at the starter supply while cranking: 1.2 V lost. Limits come from the manual (not verified)
Relay A relay has a coil (pins 85 and 86 in the usual marking) and a switch (pins 30 and 87). A small current in the coil closes the switch for a big current. Check the diagram
Fuse Replace with the same rating; never foil or wire
Wiring colours Vary by maker; do not assume
Parasitic drain Allowed draw depends on the car; typical figure not verified; use the manual
Sealing a repair Solder or crimp with the right connector and seal with heat-shrink; never twist and tape
17

Appendix E · Clutch, gearbox and driveline reference

Ask a qualified expert. Gearboxes are heavy and can fall. Use a transmission jack and a team under a qualified mechanic's supervision.

Item Note
Overall ratio gear ratio x final drive
Worked 3.6 x 4.1 = 14.76; 3000 rpm / 14.76 = 203.3 rpm at the wheels (example)
Road speed rpm x tyre circumference x 60 / (overall ratio x 1000)
Clutch slip Revs rise, speed does not
Clutch drag Hard to engage gear; air or hydraulic fault
Clutch judder Hot spots or oil on the plate
Oil level At the level plug or fill hole (Unit 2)
CV joint Boots torn: replace early; clicking on tight turns: outer joint
Differential Check level; limited-slip needs the right oil
18

Appendix F · Modern vehicles reference

Ask a qualified expert. Do not work on high-voltage or high-pressure fuel systems. Use only people trained by the maker.

Sensor or part Tells or does Fault may cause
Crankshaft position Speed and position No start
Camshaft position Valve timing position Hard start
Air flow or manifold pressure Air entering Rough idle
Coolant temperature Engine heat Hard start, fan
Oxygen sensor Rich or lean High fuel use
Throttle position Pedal Hesitation
Knock sensor Detects knock Reduced power
Injector Sprays fuel Misfire

Hybrid or electric vehicle in the shop: do not touch. Treat any orange cable as live; keep away; put a warning sign on the vehicle; refer to a trained technician; in a crash or fire stay back and call 112 and say it is a hybrid or electric vehicle. Tow flat-bed per the maker's guide.

Diesel common rail. Pressure remains after the engine stops; never loosen a line. A fluid jet can pierce the skin; get medical help at once.

19

Appendix G · Workshop systems and logs

Ask a qualified expert. For lifting equipment and safety law ask a GhIE-registered engineer and the Factories Inspectorate.

G1 · Supervisor's daily checklist

  • Lift locks, stands and chocks checked
  • Extinguishers in place; first-aid kit stocked
  • Spill kit full; floor clean
  • Waste containers labelled and sealed
  • PPE worn
  • Tool board complete
  • Job cards open and signed
  • Wheel nuts and brakes double-checked on any job touched

G2 · Logs to keep

Log Columns
Lifting equipment Date, equipment, condition, inspector, action
Incident and near-miss Date, what happened, cause, action
Comeback Date, vehicle, fault, cause, who, cost
Tool calibration Tool, date checked, by whom, next due (interval from the maker)
Waste What, how much, date, who collected
Training and apprentice Name, skill, date, who supervised
20

Appendix H · Forms to copy

H1 · Written diagnosis report

Line Write
Complaint
Conditions
Findings (numbers)
Cause
Repair
Proof (retest)
Advice

H2 · Fleet inspection (per vehicle)

Check Pass Fail Note
Tyres: pressure, tread, damage
Brakes: pedal, fluid, pad look
Steering play
Lights and indicators
Fluids and leaks
Battery and belts
Safety kit: triangle, extinguisher, first-aid

H3 · Quote with terms

Item Entry
Customer, vehicle
Parts and labour, itemised
Total and deposit
Valid until
Warranty terms (ask a lawyer about wording)
Signature

H4 · Warranty and comeback record

Date Vehicle Original job Fault found Cause Cost to garage
21

Appendix I · Used imported vehicle inspection card

A look-only list for buyers. It comes from general vendor guides, not from law, and a senior mechanic should review it before you rely on it. A garage cannot certify conformity.

Ask a qualified expert. This is general information, not legal advice. For import rules ask the Ghana Standards Authority; for roadworthiness ask DVLA; for legal disputes ask a qualified lawyer.

  • Mud, rust or silt in the engine bay, boot or under carpets; water lines in seat belts; a musty smell; odd electrics (possible flood damage)
  • Odometer: wear on the pedals, seat and steering wheel that does not match the mileage
  • Paint mismatch, uneven gaps, overspray (hidden accident repair)
  • Chassis number (VIN) on the body, windscreen and papers: do they match?
  • Tyres: brand mix, date code, age against tread
  • Hybrid battery health: refer to a trained technician
  • Catalytic converter missing or "deleted": do not accept
  • Airbag light: stays off after start; defeated bulbs are a warning

Status in Ghana. The Ghana Standards Authority runs a vehicle homologation and conformity programme under GS 4510, with enforcement reported from 1 October 2026. The vehicle age limit is not verified: reports differ and the public notice text was not readable. Ask the GSA. What to tell the customer: what you saw, in writing, and that you checked by eye only.

22

Appendix J · Illustrative cases with money

These cases are written for training. They are not records of real jobs; money figures are examples and were checked by script.

Ask a qualified expert. For disputes, contracts and tax ask a qualified lawyer or accountant; for any repair affecting safety ask a qualified mechanic.

Case Story Numbers (examples) Lesson
Comeback cost A garage skipped the second check on brake jobs. A wheel nut was left loose and the car came back 3 comebacks a month at GH¢180 = GH¢540; per year GH¢6,480. A second check of 10 minutes on 40 jobs is 6.7 hours, GH¢333 a month at GH¢50 an hour The check is cheaper than the comeback
Priced from memory A garage sold an oil service at GH¢300 Real cost: parts 240 + consumables 20 + waste 10 + labour 100 = GH¢370. Loss GH¢70 a job; 30 jobs = GH¢2,100 a month Cost the job before pricing
Part swapping A car with misfire code P0302 had three parts replaced Wrong parts GH¢600; swap-the-coil test would have cost nothing Test before you replace
Customer dispute The customer said the pads were not needed Written pad thickness (example 2 mm) and a photo ended the argument Record numbers
Fleet inspection Pre-trip check found a bulging tyre One tyre replaced before the trip Checklists prevent crashes
Business failure Garage gave credit to many customers Sales GH¢30,000; unpaid GH¢12,000; cash short for rent Chase debtors; set credit limits
23

Appendix K · Business and formula card

Ask a qualified expert. For tax, permits and money matters check with GRA, the Assembly or a qualified accountant, and ask a licensed financial adviser about loans and insurance.

Item Rule and worked example
Mark-up Profit / cost. Cost GH¢100, price GH¢125: mark-up 25 percent
Margin Profit / price. 25 / 125 = 20 percent
Price from margin cost / (1 - margin): 100 / 0.8 = 125
Break-even jobs fixed costs / gross profit per job: 5,400 / 450 = 12 jobs (from the Level 3 worked example)
Hourly rate monthly costs / billable hours
Fuel use litres / km x 100: 40 L over 480 km = 8.33 L per 100 km
Compression ratio (swept + clearance) / clearance: (452.4 + 50) / 50 = 10.05
Power kW = N.m x rpm / 9549: 150 x 4000 / 9549 = 62.8 kW
Overall gear ratio 3.6 x 4.1 = 14.76

Month-end checklist, cost sheet and permit list: see Unit 6 and Unit 5. Fees and rules for the Assembly, GRA, ORC and SSNIT are in Unit 5; check them again before acting.

24

Appendix L · Rules, offices and further learning

Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer or the named office before acting on any law, permit or licence.

Rule Known Status Who to ask Last checked
Road Traffic Regulations 2026 (L.I. 2519) Reported in the press Text not read: tyre, brake and roadside-repair rules not verified Ministry of Transport, DVLA 20 Nov 2026
Roadworthiness Via a private testing station; six centres closed in 2026 Fees not verified DVLA 20 Nov 2026
Used vehicle imports GS 4510 programme Age limit not verified The Ghana Standards Authority 20 Nov 2026
Garage waste Act 1124 Used-oil rules not verified EPA Western Region 20 Nov 2026
Workshop safety Act 328 Section numbers not verified Factories Inspectorate 20 Nov 2026

Directory template (write the contacts yourself). Local EPA office; DVLA; GSA; NVTI; GhIE; fire service; insurer; dealer technician; auto electrician.

Further learning. The US ASE tests are grouped as engine repair, automatic transmission, manual drivetrain, suspension and steering, brakes, electrical, heating and air conditioning, and engine performance; use them as a coverage checklist only, not as Ghana content (author's note; not verified here). Ask NVTI and CTVET about the current Automotive Mechanic standard.

25

Appendix M · Specialist Tools, Components and Systems

The Level 1 and Level 2 appendices define the earlier items. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item Type or size (typical) What it is and what it is used for Care Also called
Back-probe pin Fine pin Measures voltage in a connector without cutting Seal after use no other common name found
Breakout box Connector-specific Brings pins out for test As the manual shows BOB
Clamp meter DC clamp Current without cutting One wire only tong tester, current clamp
Oscilloscope 2 to 4 channels Draws a signal against time Training needed scope, lab scope
Test light 12 V type Shows voltage present Not on computer circuits circuit tester, test lamp
Transmission jack Rated in kg Lifts a gearbox Strap on gearbox jack; lifting jack
Vehicle lift Two-post, four-post, scissor, pit Raises a car Lock before work car hoist, vehicle hoist
Lifting chain and sling Marked SWL Takes the load from a hoist Inspect and log no other common name found
Pressure plate and driven plate Matched to car Press and friction plate of a clutch Replace as a set clutch disc, friction plate; clutch cover
Release bearing Matched to car Moves the pressure plate Replace with the clutch throw-out bearing, clutch bearing
Universal joint, centre bearing On propshafts Let the shaft bend; support it Check play U-joint, Cardan joint
Differential Open or limited-slip Lets wheels turn at different speeds Oil per manual diff
Common-rail pump and injectors Very high pressure Feed and spray diesel Refer fuel injector
Intercooler Air-to-air radiator Cools turbo air Check hoses charge-air cooler
Service disconnect Orange plug or switch Cuts high voltage Trained people only service plug
Spill kit and fire blanket Wall packs Spills and small fires Check monthly no other common name found
Cash book, ledger, stock card Books Business records Update daily no other common name found
26

Appendix N · Abbreviations and index

Short Meaning
CAN Controller area network
DPF Diesel particulate filter
ECU Engine control unit
EGR Exhaust gas recirculation
ISO International Organization for Standardization
PID Parameter identifier (a live data item)
SAE Society of Automotive Engineers (USA)
SWL Safe working load

Where to find it. Diagnostic charts: Appendix A. Scan data: Appendix B. OBD: Appendix C. Electrical: Appendix D. Driveline: Appendix E. Modern vehicles: Appendix F. Logs: Appendix G. Forms: Appendix H. Imports: Appendix I. Cases: Appendix J. Business: Appendix K. Rules: Appendix L. Tools: Appendix M.

27

Further reading and sources

Best next reads: the workshop manual of the vehicles you work on; the maker's training pages; the Hub's Money Skills Level 2 and Entrepreneurial Thinking Level 2; Workplace Safety for the Hub's safety training.

What this module does not cover: automatic transmission repair, high-voltage hybrid and electric work, high-pressure diesel injection repair, engine rebuilds, vehicle body repair, car air-conditioning gas (see Refrigeration and AC Basics), motorbikes, and Ghana parts prices (not found reliably). The DVLA fees, STMA garage fee, EPA used-oil rules, compulsory insurance and NVTI grades were not verified.

Every source used in this manual is listed, with links, in the Teacher Copy.

One application of the Cold-Start Learning Kit, which stays general-purpose and can build a guide on any topic in any field. Written in CTVET format; not a CTVET curriculum.