← All training manualsAuto Mechanics Basics · read-onlyGet the PDF with Teacher Copy (GH¢50)
Training module · National Proficiency I · CTVET formatTrainee Manual

Auto Mechanics Basics

Learn to look after a car the safe way. Jack stands first, then oil, tyres, brakes, battery and cooling, then simple fault-finding and your first customers.

A car raised on jack stands with a mechanic checking the wheel A saloon car with its front raised on a trolley jack and two jack stands, a wheel off beside it, and a mechanic in overalls and safety boots tightening a wheel nut with a wrench. To the left, a toolbox and an oil can. To the right, a tyre stack and a battery. Wheel chocks sit behind the rear wheel. TOOLS · OILJACK STANDS FIRSTBATTERY
Trainee name
Training centre
Start date
Instructor
Prepared by De-Graft Afful · Version 1.1.0 · November 2026
01

About this module

A car is a heavy machine with hot parts, fuel, electricity and moving metal. It is also one of the most useful things a person can learn to look after. Learn the safe way first, and the skills will pay you for life.

Who it is for. People with no formal certificate, aged 18 or over. National Proficiency I is a bridging level for people with little or no formal education; holders do routine tasks under supervision. In Ghana, nobody under 18 may do hazardous work.

Why this trade

  • Many Ghanaian mechanics learn by apprenticeship and by memory, and many work in roadside garages. This module adds a safe, step-by-step method to that.
  • Takoradi has a Kokompe branch of the Ghana National Association of Garages, so there is a local community of master mechanics to learn from.
  • Every car, pickup and minibus needs regular care. Routine service, tyres, brakes, battery and cooling are the jobs that come back again and again.

CTVET has an Automotive Mechanic programme. The CTVET list of competency-based programmes shows "Automotive Mechanic" at NP I and NP II, approved on 28 April 2020, with an expiry date of 27 April 2025 on the page. The unit list was not found online, so this module is not that curriculum. Ask CTVET, NVTI or the regional Ghana TVET Service office for the current standard and trade-test rules, and match this module to it. The trade-test grades are not verified.

What this module does and does not cover

  • Covers: cars, pickups and minibuses (petrol, and diesel where the steps are the same); safety; routine service; wheels, tyres and brake checks; battery, charging and cooling; first fault-finding; starting a small business.
  • Does not cover: motorbikes and tricycles (see the Hub's Motorbike and Tricycle Servicing); car air-conditioning gas (see Refrigeration and AC Basics; refrigerant handling is not taught here and needs a certified technician); generators and outboard motors (see Appliance and Generator Repair and Outboard Motor Repair); engine rebuilds, gearbox repair, hybrid and electric vehicles.

How the module works

Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent by being watched at work, by your jobs, by answering questions, and by your logbook. About 70% of the time is practical.

02

Unit 1 · Workshop and vehicle safety

A car can crush you, burn you, poison you with exhaust and set itself on fire. Every rule in this unit protects your hands, your lungs, your eyes and your life.

Competency standard

Learning outcome Performance criteria — the trainee…
1.1 Wear the right PPE wears safety glasses, gloves, overalls and safety boots for the job
1.2 Lift and support safely lifts only at jack points, places jack stands, never works under a jack alone
1.3 Prevent fire and burns keeps fuel and rags safe; knows the extinguisher; waits for hot parts to cool
1.4 Control exhaust, battery and chemical hazards runs engines only in open air or with extraction; treats battery, coolant and brake fluid with care
1.5 Handle used oil and waste responsibly stores used oil sealed and labelled; never pours it on the ground or in a drain

Range. All workshop work. Evidence. Observation every session; oral questions.

Tools and items for this unit

Every item is named here and defined. Sizes are typical; the maker's plate or the vehicle manual rules. The standard English trade name is used, with other common names in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item What it is and what it does Type or size (typical) Care or safety Also called
Jack stand (axle stand) A steel stand with a pin or ratchet that holds a lifted vehicle. A jack only lifts; the stand holds. Sold in pairs with a rated load per stand, marked on the plate; height range varies Check weld, pin and base for cracks or bends; never use a bent stand. The rating must be on the plate. axle stand, safety stand; lifting jack
Trolley jack A wheeled hydraulic jack with a long handle that lifts one end of a car. Rated in tonnes on the body Lift only at the manual's jack points. Never the only support. floor jack, garage jack; lifting jack
Wheel chock A wedge that stops a wheel from rolling. Rubber, plastic or wood; use at least two Put against the wheel diagonally opposite the lifted wheel. wheel wedge, wheel stop
Safety glasses or goggles Clear eye guards against splashes, dust and flying metal. Wrap-around type, marked to a safety standard (ask a safety professional) Replace if scratched. Wear for every job. safety goggles, eye protection
Nitrile gloves and heavy work gloves Nitrile is thin and oil-proof. Heavy gloves protect from rough or hot work. Nitrile is disposable; leather or fabric for rough work Never wear gloves near a rotating part or belt. no other common name found
Overalls and safety boots Overalls cover the body from oil. Safety boots protect toes and give grip. Steel or composite toe-cap boots Keep clean. Oily overalls burn quickly. coveralls, boiler suit
Fire extinguisher (ABC dry powder) A pressurised bottle that puts out fires of wood, liquids and electrical origin. Several sizes; the right type and size for a garage: ask the Ghana National Fire Service (not verified here) Know where it is and how to use it. fire extinguisher bottle
First-aid kit and eye-wash bottle The kit holds dressings for small injuries. The eye-wash bottle rinses fluid or dust from the eye. Contents: ask a qualified first-aider (not verified here) Check monthly; replace used items. For serious injury call 112. first aid box
Drip tray, drain pan and used-oil drum A tray catches drips. The pan catches oil from the sump. The sealed, labelled drum stores used oil. Pan sized to the sump capacity plus a margin; drum with a tight lid Never pour oil on the ground or in a drain. drip pan; oil pan, catch pan
Absorbent sand or sawdust Soaks up spilt oil or fuel so you can sweep it out. A covered bin or bucket Do not wash spills into the drain. no other common name found

Parts and safety: Trolley jack and jack stand

Photograph of a trolley jack and a jack stand under a carA real black trolley jack with a white lifting arm and a long handle stands under the side of a silver car, with a ratcheted jack stand beside it on the left. Two wheels of the jack are visible.12345
A real trolley jack and a jack stand beside a car. Numbers on the picture match the table below. (Photo: Mark Hunter, CC BY 2.0; Source: Photo Trolley Jack)

Photo credit: Mark Hunter, CC BY 2.0.

No. Part What it does Safety rule
1 Saddle The small cup on top that touches the car's lifting point Put it only on the lifting point the manual shows
2 Lifting arm Swings up and raises the saddle when you pump Keep your hands clear of the arm while it moves
3 Handle Pumps the jack up and releases it down Lower slowly; never let it drop
4 Castor wheel Lets you roll the jack under the car Roll on firm, level ground only
5 Jack stand Holds the car up after the jack has lifted it A jack only lifts; put a stand under the car before any part of you goes under
Trolley jack and jack stand Trolley jack and jack stand with numbered parts underside of the car (strong point) 1 2 3 4 5 6 7 8 9
Trolley jack and jack stand. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Saddle (jack head) Takes the load at the car's jack point Lift only at the manual's jack points
2 Ram (lifting piston) Rises when the handle is pumped Do not exceed the jack's rating
3 Handle Pumps the jack up; turned to lower it Keep hands clear when lowering
4 Release valve Lets the fluid return so the jack goes down slowly Open slowly
5 Wheels and base Let you roll the jack under the car Use on firm, level ground only
6 Stand saddle Cradles the strong point of the car Place under the strong points shown in the manual
7 Stand column with teeth Sets the height in steps Check for bends and cracks before use
8 Locking pawl or pin Holds the column at the chosen height Make sure it is fully engaged
9 Stand base Spreads the load on the ground Never on soft sand or a broken slab

Safety protocol: Trolley jack and jack stand

Before. Wear glasses, gloves, boots. Check the jack and stands for leaks, bends, cracks and a readable rating plate. Chock wheels, park on dry level firm ground, handbrake on.

While you work. Lift only at jack points. Lower onto rated stands. Shake the car before going under. Never use bricks, blocks or wood. Never work under a car held by a jack alone.

After. Lift, remove stands, lower gently. Wipe the jack, lower the ram fully, store the stands dry. Report a leaking jack or a damaged stand and take it out of use.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor. If a car falls on someone, do not get under it: raise the alarm and call 112.

Ask a qualified expert. For lifting, brakes, fuel, battery, electrical or other dangerous work on a vehicle, ask a qualified mechanic or a GhIE-registered engineer, and use a licensed electrician or a qualified safety officer for workshop wiring and fire safety. Do not attempt work you are not trained and authorised to do. For any injury, illness or poisoning, see a doctor or nurse; in an emergency call 112. This unit teaches awareness and good practice, not medical treatment.

Never get under a vehicle held up only by a jack

A jack is for lifting. It is not for holding. Never get under a vehicle supported only by a jack. United States health researchers record workers killed by vehicles that fell off jacks, and say a jack should never be the only support when someone is under the vehicle.

The safe way, in order:

  1. Park on dry, level, firm ground. Soft sand, a slope or a broken slab can let a jack slip.
  2. Put an automatic car in Park, or a manual car in low gear, and apply the handbrake.
  3. Chock the wheels diagonally opposite the wheel you will raise.
  4. Find the jack point in the owner's manual. Lift only there. Do not exceed the jack's rated weight.
  5. Lift just high enough, then place rated jack stands under the strong points shown in the manual.
  6. Lower the vehicle gently onto the stands. Shake the car to test it before you go under.
  7. Keep the jack in place as a back-up, but never trust it alone.
  8. Wear eye protection. If you work alone, tell someone and agree to check in.

Bricks, blocks and wood. Do not use concrete blocks, bricks, tyres or loose wood as a support under a vehicle. They can crack or slide. Use rated jack stands only. The sources found here do not give a Ghana rule on this; it is the safe practice, so follow it. Ask a qualified mechanic if unsure.

Exhaust: the silent killer

Engine exhaust contains carbon monoxide (CO), a gas you cannot see or smell. The US Centers for Disease Control say never to run a vehicle in an enclosed garage, and that an open door does not make an attached garage safe. In a workshop, run engines outdoors or in the open bay, with the exhaust pointing out, and never in a closed room. If you feel headache, dizziness or sleepiness near a running engine, move into fresh air and get help.

Fuel and fire

  • Petrol vapour catches fire from a spark, a cigarette, a hot manifold or a phone charger. No smoking, no naked flame and no grinding near fuel.
  • Do not drain a fuel tank near a pit or a drain.
  • Keep oily rags in a closed metal bin. Soak up spills with sand or sawdust and sweep them out.
  • Keep two extinguishers where you can reach them quickly, and know how to use them. Ask your local Ghana National Fire Service station about fire safety training for your workshop.
  • Never fill a hot engine's fuel system or open a fuel line without releasing pressure the way the manual says. Fuel-system work on injection engines is a job for a trained mechanic.

Hot parts and pressure

The radiator and coolant system run under pressure. Opening the cap on a hot engine can spray boiling coolant. Wait for the engine to cool, turn the cap slowly to release pressure, and wear gloves and glasses. Exhaust pipes, the manifold and the oil can burn you too. Let the engine cool before work.

Battery, coolant and brake fluid

  • A lead-acid battery gives off flammable hydrogen gas and contains acid. Keep sparks and flames away, wear glasses, and do not jump or charge a frozen, cracked or leaking battery.
  • Coolant (antifreeze) contains ethylene glycol, which is very poisonous. It tastes sweet, so children and animals may drink it. Keep it in a labelled container with a lid and wipe up spills.
  • Brake fluid damages paint and skin. Wipe it off at once; keep the container closed.

Used oil and workshop waste

The Environmental Protection Agency has warned that waste from garages is a major health and environment hazard: used oil and fuel can reach drains, soil and groundwater. That warning dates from 2013. The Environmental Protection Act 2025 (Act 1124) now replaces the old EPA Act and covers hazardous waste, but the exact rules for used oil, filters and batteries were not verified. Ask the EPA office in Takoradi where used oil is collected and what a garage must do.

Good habits in the meantime (adapted from United Kingdom guidance, foreign source): keep used oil in sealed, labelled containers standing on a drip tray, away from drains and water, and hand it to a collector who is allowed to take it. Never pour oil on the ground or into a gutter.

Clothing and PPE

Wear overalls, safety boots, safety glasses and gloves suited to the job: nitrile for oil and fluids, heavier gloves for rough work. Tie back long hair, and remove rings, watches and chains before working near moving parts or the battery.

Safe or unsafe?

Your trainer describes eight scenes. For each, say safe or unsafe and why.

Lift and support a vehicle (instructor present)

  1. Dress in full PPE; your partner checks you.
  2. Park the training car on level, dry, firm ground. Handbrake on, gear in Park or low.
  3. Chock the wheels diagonally opposite the wheel you will lift.
  4. With the instructor, find the jack points in the owner's manual and write the page number in your logbook.
  5. Lift one end slightly, place two rated jack stands at the strong points, and lower the car onto them.
  6. Shake the car from the side. Never put any part of your body under the car if it moves.
  7. Lift the car again, remove the stands and lower it fully. Record each step in your logbook.

Look around

Visit a garage near you (from a safe distance). Note three safe things and three unsafe things you see. Do not enter the work area without permission.

Check yourself: Unit 1

  1. What must support a car before you go under it?
  2. Why must you never run an engine in a closed room?
  3. What do you do before opening a radiator cap?
03

Unit 2 · Know your vehicle: parts, tools and fluids

You cannot fix what you cannot name. Learn the main systems, the tools and the fluids before you touch a bolt.

Competency standard

Learning outcome Performance criteria — the trainee…
2.1 Name the main systems names the engine, fuel, cooling, lubrication, electrical, transmission, brake, steering and suspension systems and what each does
2.2 Use the owner's manual finds service intervals, fluid types, tyre pressures, jack points and fuse positions
2.3 Choose and use hand tools selects the right spanner or socket; uses a torque wrench
2.4 Identify fluids finds and checks engine oil, coolant, brake fluid, power-steering fluid and screen wash

Range. Petrol saloon car, pickup or minibus; basic hand tools. Evidence. Observation; oral questions; vehicle map in the logbook.

Tools and items for this unit

Every item is named here and defined. Sizes are typical; the maker's plate or the vehicle manual rules. The standard English trade name is used, with other common names in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item What it is and what it does Type or size (typical) Care or safety Also called
Combination spanner A spanner with an open end and a ring end of the same size, used to undo nuts and bolts. Metric sizes, for example 8 to 19 mm (metric sets are common on cars) Pull towards you. A wrong size rounds the corners. wrench, open-end and ring spanner
Socket set, ratchet and extension Sockets fit over a nut; the ratchet turns it in one direction; the extension reaches deep bolts. Drive sizes 1/4, 3/8 and 1/2 inch Use the right drive size. Do not hammer a ratchet. socket wrench set; ratchet handle
Torque wrench A wrench that clicks or shows when the set tightening force is reached. Click type, for example 20 to 200 N.m range (typical) Wind it back to its lowest setting after use. Ask the maker about calibration. torque spanner
Breaker bar A long solid bar with a swivel head to loosen tight bolts. It is for loosening, not for the final tightening. About 40 to 60 cm long, 1/2 inch drive (typical) Do not use it to tighten to a torque. breaker handle, power bar
Oil filter wrench A tool that grips a stuck spin-on filter. Types: strap, cup and chain. Match the filter diameter Keep the pan underneath; old oil spills. filter strap wrench
Screwdrivers and pliers Phillips (cross-head), flat and Torx drivers turn screws. Long-nose pliers hold small parts. Locking pliers clamp. Several sizes of each Use the right tip so it does not slip. pincers; driver
Hammer (ball-pein and soft-faced) The ball-pein hammer is for metal work. The soft-faced hammer taps parts without marking them. About 0.3 to 0.5 kg for general use (typical) Never hit a hardened tool or a socket. mallet (soft-faced)
Tyre pressure gauge and tread depth gauge The pressure gauge reads air pressure in psi, bar or kPa. The tread gauge measures groove depth in mm. Pencil, dial and digital types Check accuracy against another gauge. Keep clean. tire gauge, tyre gauge; tread gauge
Digital multimeter A meter that reads volts, ohms (resistance) and often amps. It has red and black leads and a dial. Auto-range or manual range; one with a fused 10 A socket Start on the highest range if manual. Use only as the book shows. DMM, volt-ohm meter, avometer
Dipstick A rod with MIN and MAX marks that shows engine oil level. Yellow or orange handle usually Wipe, push fully in, pull out and read. oil level stick
Funnel and drain pan The funnel guides new fluid in without spilling. The pan catches used fluid. Clean funnel kept for one fluid type Do not mix funnels between oil, coolant and brake fluid. oil pan, catch pan; filling funnel
Owner's manual The booklet from the maker with fluid grades, tyre pressures, jack points, fuse positions and service times. Paper or digital; one per vehicle It overrules this book. handbook, owner's handbook
Radiator, thermostat, hoses, water pump, expansion tank The cooling system parts. The radiator gives heat to the air; the thermostat opens when warm; hoses carry coolant; the pump pushes it; the tank holds spare coolant. Visible under the bonnet Look only when cold; do not open when hot. no other common name found
Fuse and fuse box A fuse is a thin strip in a plastic body that melts to protect a wire if current is too high. The box holds them. Blade fuses in colours that mark the amp rating Replace only with the same rating, never with foil or wire. blade fuse

Parts and safety: Click-type torque wrench

Photograph of a click-type torque wrenchA real click-type torque wrench lying on a stone floor. A knurled adjustable handle is at the top left, a long polished steel tube runs down to the right, and a ratchet head with a large socket fitted is at the bottom right.1234
A real click-type torque wrench with a socket fitted. Numbers on the picture match the table below. (Photo: Wikimedia Commons user, CC BY-SA 3.0; Source: Photo Torque Wrench)

Photo credit: Wikimedia Commons user, CC BY-SA 3.0.

No. Part What it does Safety rule
1 Adjustable handle (grip) The knurled end you hold and turn to set the torque value Set the value from the manual; wind back to the lowest setting after use
2 Tube (beam) The long steel body that gives you the pull Pull smoothly; do not add a pipe to lengthen it
3 Ratchet head Turns the socket and clicks when the set torque is reached Stop pulling at the click
4 Socket Fits over the nut or bolt head Use the size that fits so the corners do not round off
Click-type torque wrench Click-type torque wrench with numbered parts 1 2 3 4 5 6
Click-type torque wrench. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Handle (grip) Where you pull; pull smoothly Pull towards you, never with a pipe extension
2 Setting scale and barrel Shows and sets the torque value Check the unit (N.m or lb-ft) before setting
3 Ratchet head Turns the socket and clicks at the set torque Stop pulling at the click
4 Square drive Holds the socket Match the drive size to the socket
5 Socket Fits the nut or bolt Use the right size so corners do not round off
6 Lock ring Locks the set value Lock after setting

Safety protocol: Click-type torque wrench

Before. Check the scale is readable and the wrench has been stored at its lowest setting; check the socket fits. Wear glasses and gloves.

While you work. Set the value from the manual. Pull slowly in one smooth movement. Stop at the click. Do not use it to loosen bolts, do not drop it, do not use it as a hammer.

After. Wind it back to the lowest setting, wipe it, store it in its case. Report any wrench that is dropped or clicks wrongly; ask the maker about calibration.

Emergency. If a socket slips and hurts your hand, stop. For serious injury call 112; first aid only if trained.

Parts and safety: Digital multimeter

Digital multimeter Digital multimeter with numbered parts COM V/ohm 10A 1 2 3 4 5 6 7
Digital multimeter. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Display Shows the reading Read it before you move the probes
2 Selector dial Chooses volts, ohms or amps Set the function before connecting; start high if manual range
3 COM socket Black lead goes here (common) Black lead always in COM
4 V/ohm socket Red lead for volts and ohms Never in the 10 A socket when measuring volts
5 10 A socket (fused) Red lead for measuring current Only connect in series; the meter fuse can blow
6 Black lead and probe Negative side of the test Check the insulation is not cracked
7 Red lead and probe Positive side of the test Do not touch the metal tips while testing

Safety protocol: Digital multimeter

Before. Check leads, probes and the case for damage. Set the dial to DC volts (20 V range) for battery tests. Wear glasses and gloves.

While you work. Connect black first, then red. Touch only what the book tells you. Do not measure resistance on a live circuit. Never put a meter across a battery on the amp range.

After. Switch off, coil the leads, store dry. Replace a blown fuse with the same type. Report a damaged meter.

Emergency. Battery spark or burn: move away, cool a burn under running water, call 112 for serious injury.

Parts and safety: Engine bay map

Engine bay map Engine bay map with numbered parts 1 2 3 4 5 6 7 8 9
Engine bay map. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Radiator Cools the engine coolant Never open the cap when hot
2 Engine with oil filler cap and dipstick Makes power; oil is checked on the dipstick Hot parts: let it cool; engine off for checks
3 Battery Stores electricity Sparks and acid: gloves, glasses
4 Alternator and drive belt Recharges the battery Keep hands away when running
5 Brake fluid reservoir Holds brake fluid Keep closed; fluid harms paint and skin
6 Coolant reservoir Holds spare coolant (MIN and MAX) Coolant is poisonous
7 Air filter box Cleans air for the engine Replace if blocked
8 Fuse box Holds fuses Replace only with the same rating
9 Screen-wash bottle Holds washer liquid Use screen wash only

Safety protocol: Engine bay map

Before. Engine off and cool. Park level, handbrake on. Open the bonnet and support it with its prop. Wear glasses and gloves.

While you work. Touch only what you came to check. Keep hair, sleeves and tools away from belts and the fan. Never open the radiator cap hot. No smoking or flame.

After. Close caps, remove rags and tools (count them), close and latch the bonnet. Write any leak or fault in the logbook.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Ask a qualified expert. If a job needs lifting, fuel-system, brake, airbag, electrical or air-conditioning work you have not been trained for, ask a qualified mechanic or a GhIE-registered engineer. Never open or work near airbags and do not handle air-conditioning gas.

The ten systems in plain words

System What it does What you can check at this level
Engine Burns fuel to make power Noise, smoke, leaks, oil level
Fuel Brings fuel from the tank to the engine Leaks, filter service dates (look only)
Air intake and exhaust Brings in clean air, takes out exhaust Air filter, exhaust leaks and hangers
Cooling Keeps the engine from overheating Coolant level, hoses, fan, belt
Lubrication Oil reduces friction and cools parts Oil level and condition
Electrical Battery, alternator, starter, lights, fuses Battery, terminals, lights, fuses
Transmission Carries power to the wheels (manual or automatic) Fluid leaks, odd noises, clutch feel
Brakes Slow and stop the car Pedal feel, fluid level, pad look
Steering Points the wheels Free play, noises, fluid level
Suspension and tyres Carry the car, absorb bumps, grip the road Tyres, shocks leaking, uneven sitting

The owner's manual

Every vehicle has an owner's manual. It tells you the oil grade, the fluid types, the tyre pressures, the jack points, the fuse positions and the service schedule. When this book and the manual disagree, the manual wins. If a vehicle has no manual, ask the maker's dealer or a qualified mechanic, and do not guess fluid types.

Engine oil in two lines

An oil grade such as 5W-30 has two parts: the first number with W (for winter) shows how it flows when cold; the second shows thickness when hot. The oil also has a service rating from the American Petroleum Institute. Use what the owner's manual says. Using the wrong oil can harm the engine.

Hand tools and the torque wrench

Tool Use
Combination spanners and sockets Undoing and tightening nuts and bolts; use the correct size so the corners do not round off
Ratchet and extension Reaching bolts in tight places
Torque wrench Tightens to the exact figure in the manual; used for wheel nuts and other critical bolts
Oil filter wrench Removes a stuck oil filter
Screwdrivers, pliers, hammer General work
Tyre pressure gauge, tread depth gauge Tyre checks
Digital multimeter Reads battery voltage (Unit 5)
Funnel and drain pan Clean fluid changes

Rules: pull a spanner towards you, never push with your knuckles in front; never use a pipe on a spanner to get extra force; keep tools clean and in a box; count your tools before you close the bonnet.

Finding the fluids

Open the bonnet and find: the engine oil dipstick and filler cap; the coolant reservoir (with MIN and MAX marks); the brake fluid reservoir; the power-steering reservoir (if fitted); the screen-wash bottle; and the battery. Draw a simple map in your logbook and write the type of each fluid from the manual.

Vehicle tour

  1. With the engine off and cool, open the bonnet and find each item on the fluid list.
  2. In the owner's manual, find and write down: oil grade and quantity, tyre pressures, jack points, fuse box locations, and the service interval.
  3. Name every system in the table and point to one part of each.
  4. Use a torque wrench on a spare bolt with your instructor to feel how it clicks.
  5. Draw a map of the engine bay in your logbook.

Manual hunt

Find the owner's manual (or a copy) for a car you know. Write down the oil grade, the tyre pressure and the service interval.

Check yourself: Unit 2

  1. Name five of the ten systems.
  2. What does the 5W in 5W-30 describe?
  3. Which tool tightens a wheel nut to the exact figure?
04

Unit 3 · Routine service step by step

Most breakdowns start as small things nobody checked. A good routine service stops them.

Competency standard

Learning outcome Performance criteria — the trainee…
3.1 Check and top up fluids checks oil, coolant, brake fluid, power-steering fluid and screen wash; tops up with the right type
3.2 Change engine oil and filter drains, replaces, refills and checks for leaks following the steps
3.3 Check air filter, lights, wipers and belts inspects and replaces simple items
3.4 Keep a service record records date, mileage, work done and parts used

Range. Petrol and diesel light vehicles, routine service only. Evidence. Observation; completed service record.

Tools and items for this unit

Every item is named here and defined. Sizes are typical; the maker's plate or the vehicle manual rules. The standard English trade name is used, with other common names in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item What it is and what it does Type or size (typical) Care or safety Also called
Engine oil The liquid that reduces friction and carries heat in the engine. Grade such as 5W-30, as the manual says Used oil is hazardous waste. motor oil
Oil filter A canister or cartridge that traps dirt from the oil. A spin-on type screws on; a cartridge type sits in a housing. Must match the engine; look up by vehicle Wet the rubber ring with a drop of new oil. no other common name found
Drain plug and crush washer The drain plug closes the sump. The crush washer is a soft metal or fibre ring that seals it and is flattened when tightened. Size from the manual Use a new washer every time; do not over-tighten. sump plug; sealing washer
Air filter A paper or foam element that cleans air going into the engine. Panel or round; match the vehicle Replace if blocked; do not wash a paper filter. air cleaner element
Cabin filter A filter in the dashboard air path that cleans the air you breathe. Behind the glovebox in many cars (see manual) Replace as the manual says. pollen filter, A/C filter
Fuel filter Traps dirt and water in the fuel before the engine. Fuel-system work is outside this level. Inline or in the tank Look at the service date only; do not open at this level. no other common name found
Wiper blade and screen wash The blade clears the screen. Screen wash is cleaning liquid. Length is on the old blade or in the manual Replace split blades. no other common name found
Bulb The light source in a lamp. Types differ by cap and wattage. Match the type in the manual Do not touch a halogen glass with bare fingers. lamp
Drive belt (V-belt or ribbed belt) A belt that turns the alternator and other parts from the engine. A timing belt is inside the engine and is not touched here. Ribbed belts have several grooves Look for cracks, fraying and shine. fan belt, serpentine belt
Rag, absorbent and used-oil container Rags wipe oil; absorbent soaks spills; the labelled container stores used oil. Closed metal bin for oily rags Oily rags can heat and ignite; keep them in a metal bin. shop cloth, wipe

Safety protocol: oil and filter change

Before. Park on firm level ground, handbrake on, chock the opposite wheel, glasses and gloves. engine warm not hot, drain pan and labelled container ready.

While you work. Never drain hot oil. No smoking. Use the manual's drain-plug torque.

After. Recheck for leaks, seal used oil in a labelled container, wash hands, record in the logbook.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Ask a qualified expert. Fuel-system, brake, steering, airbag and electrical work are outside this unit. Ask a qualified mechanic or a GhIE-registered engineer. The service intervals in your owner's manual are the authority; this book gives method, not a schedule.

Service intervals

The right time to service depends on the vehicle, the fuel and the roads. Follow the service schedule in the owner's manual. Dusty roads and short, stop-start trips are harder on a car; if the manual lists a "severe use" schedule, use it. Do not copy a number of kilometres from this book: not verified for your vehicle.

Fluid checks (engine off, car on level ground)

  1. Engine oil. Wait a few minutes after stopping. Pull the dipstick, wipe it, push it fully in, pull it out again. The level must be between the marks. Look at the oil: very dark and gritty, milky or smelling of fuel are warnings. Report them.
  2. Coolant. Look at the reservoir when the engine is cold; the level must be between MIN and MAX. Never open the radiator cap on a hot engine.
  3. Brake fluid. The level should be between MIN and MAX. A level that drops quickly means a leak or worn pads; see Unit 4. Brake fluid takes in moisture over time, and many sources say to replace it about every two years or as the manual says. The manufacturer is a lubricant seller; follow the manual.
  4. Power steering, screen wash. Top up to the mark with the type in the manual.

Oil and filter change, step by step

Oil and filter change

  1. Read the manual: oil grade, quantity, filter type, drain-plug torque. Buy the right oil, a new filter and a new drain-plug washer.
  2. Warm the engine for a few minutes, then switch it off. Warm oil drains better; hot oil burns.
  3. Park on level ground, handbrake on. If you must lift the car, lift and support it exactly as in Unit 1. Where the car is high enough, a level, firm floor is enough.
  4. Put on gloves and glasses. Slide the drain pan under the sump.
  5. Remove the oil filler cap, then slowly unscrew the drain plug by hand at the end. Keep the plug pressed to the sump until the last turns, then let the oil flow.
  6. Let it drain fully. Wipe the plug, fit the new washer, and tighten to the torque in the manual.
  7. Move the pan under the filter. Unscrew the old filter with the filter wrench. Old oil spills out; keep the pan under it.
  8. Wipe the filter seat. Smear a little new oil on the new filter's rubber ring. Screw it on by hand; tighten as the instructions on the filter say.
  9. Pour in the correct oil through a funnel, a little less than the full amount.
  10. Check the dipstick. Add oil until it is at the top mark. Do not overfill.
  11. Start the engine and let it idle for a minute. The oil warning light should go off. Check under the car for leaks. Stop the engine, wait, and recheck the dipstick.
  12. Pour the used oil into a sealed, labelled container. Never into a drain or on the ground. Wash your hands with soap.
  13. Write the date, mileage, oil grade and filter in the service record.

Tight, but not too tight. An over-tightened drain plug can strip the sump thread, which is a costly repair. A plug that is too loose will leak. Use the torque wrench and the figure in the manual.

Other routine checks

  • Air filter. Take out the filter, hold it to the light, and tap it. If it is very dirty, replace it. A dirty filter makes the engine work harder.
  • Lights. With a helper, check headlights (low and high beam), indicators, brake lights, reverse lights and number-plate lights. Replace a blown bulb with the same type.
  • Wipers and screen wash. Replace split blades. Fill the wash bottle.
  • Belts and hoses (look only). With the engine off, look for cracks, fraying or shine on the belts and for soft or swollen hoses. Report them. Changing a timing belt is not done at this level.
  • Leaks. Look under the parked car for drips and note the colour: dark oil, green or pink coolant, clear water from air-conditioning is normal.
  • Horn and handbrake. Test both.

The service record

Write for every vehicle: owner, number plate, date, mileage, work done, parts used, what you advise next time. A good record shows the customer you are careful, and it protects you in an argument.

Date Mileage Work done Parts Advice next visit
Example row 85,400 Oil and filter; air filter checked Oil 4 L, filter Brake pads look worn: check

Service sheet

A customer's car has a 4-litre sump. Your oil costs GH¢60 a litre (example) and the filter GH¢45 (example). The drain-plug washer is GH¢5 (example). Labour for the job is GH¢100 (example). (1) What do the parts cost? (2) What is the total? (3) If you add a 20% margin on the total, what do you charge?

Service record

Write a service record for a car you help with at home or at a garage. List what you would check at the next service.

Check yourself: Unit 3

  1. Why warm the engine briefly before draining the oil?
  2. Where must used oil go?
  3. Name two things to write in the service record.
05

Unit 4 · Wheels, tyres and brake checks

Tyres are the only part of the car that touch the road. Brakes are the only thing that stops it. Check both every time.

Competency standard

Learning outcome Performance criteria — the trainee…
4.1 Check tyres checks pressure, tread, damage and age; reads the placard
4.2 Change a wheel safely jacks, supports, removes, refits and torques in a star pattern
4.3 Inspect brakes checks pedal, fluid and visible pad wear; reports faults
4.4 Know the limit refers brake repairs to a qualified mechanic

Range. Passenger car or pickup; checks and wheel change only. Brake repair is not taught at this level. Evidence. Observation; wheel change checked; oral questions.

Tools and items for this unit

Every item is named here and defined. Sizes are typical; the maker's plate or the vehicle manual rules. The standard English trade name is used, with other common names in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item What it is and what it does Type or size (typical) Care or safety Also called
Wheel brace or wheel spanner A cross-shaped or long-handled spanner that fits the wheel nut. It loosens the nuts on the ground. Socket size depends on the car; check the nut A longer bar gives more force: loosen only, do not final-tighten with it. wrench, open-end and ring spanner; lug wrench, tyre iron
Wheel nut and wheel stud The stud is a threaded bolt fixed in the hub. The nut screws onto it to hold the wheel. Thread size such as M12 x 1.5 (typical; check the manual) Check studs for damaged threads. Do not oil threads unless the manual says. lug nut; wheel bolt
Valve stem and valve cap The small valve you inflate through. The cap keeps dirt out. Rubber or metal Check for leaks with soapy water. tyre valve
Spare wheel and tyre A spare for emergencies, which may be a smaller space-saver type. See the manual for speed and distance limits Check its pressure monthly. spare tyre
Treadwear indicator Small raised bars in the main grooves of a tyre. When the tread is level with them the tyre is worn out. Marked on the sidewall with TWI or an arrow on many tyres Replace when level with them or earlier. wear bar, tread wear bar
Brake pad and brake disc The pad is a block of friction material that squeezes the disc, which turns with the wheel, to slow the car. About 3 mm of pad is a common replacement warning; the manual rules Inspect and report only at this level. brake rotor; brake lining
Brake fluid and brake reservoir The fluid passes force from the pedal to the brakes. The reservoir holds it, on top of the master cylinder. Grade DOT 3, 4 or 5.1 as the cap says Keep closed; it absorbs moisture and damages paint. no other common name found
Master cylinder, caliper and brake hose The master cylinder is worked by the pedal. The caliper holds the pads at the disc. The hose carries fluid to the caliper. Fixed parts; look only Fluid on or near them means a leak. brake master

Parts and safety: Disc brake at one wheel

Photograph of a brake disc, caliper and hub on a carA real rusty brake disc with a caliper on its left, a hub with bolt holes and a central stub in the middle, photographed with the wheel removed.1234
A real, rusty brake disc and caliper on a car with the wheel removed. Numbers on the picture match the table below. (Photo: Shixart1985, CC BY 2.0; Source: Photo Disc Brake)

Photo credit: Shixart1985, CC BY 2.0.

No. Part What it does Safety rule
1 Brake disc (rotor) The metal disc that turns with the wheel; the pads grip its flat faces Deep rust, grooves or a raised lip mean it needs checking by your instructor
2 Caliper Holds the brake pads and squeezes them onto the disc Look and report only at this level; never hang it by the hose
3 Wheel bolt hole One of the holes the wheel studs or bolts pass through Keep threads clean; tighten wheel nuts in a star pattern
4 Hub The centre that carries the wheel and the disc Do not touch a hot hub or disc; check for play and report
Disc brake at one wheel Disc brake at one wheel with numbered parts 1 2 3 4 5 6 7
Disc brake at one wheel. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Brake disc (rotor) Turns with the wheel; the pads grip it Look for deep grooves and a lip; do not touch when hot
2 Brake pads Friction blocks pressed onto the disc Replace in axle sets
3 Caliper Holds the pads and squeezes them Hang by wire, never by the hose
4 Piston Pushes the pad onto the disc Push back slowly; watch the reservoir level
5 Brake hose Carries fluid to the caliper Replace if cracked or swollen
6 Hub Carries the wheel and disc Check for play (bearing)
7 Wheel studs Hold the wheel on Check threads; torque nuts in a star pattern

Safety protocol: Disc brake at one wheel

Before. Park on firm level ground, chock, lift and support on rated stands. Wear glasses, gloves, a dust mask. Brakes are inspected and reported at Level 1: do not dismantle.

While you work. Look and report only. Never blow brake dust off; wet-wipe it. Do not touch hot discs.

After. Refit the wheel and torque the nuts in a star pattern. Lower the car. Write what you saw and report to your instructor.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Safety protocol: wheel change

Before. Park on firm level ground, handbrake on, chock the opposite wheel, glasses and gloves.

While you work. Loosen nuts on the ground, lift at the jack point, place a stand before any part of you goes under. Never hot oil, never a jack alone, no smoking. Tighten wheel nuts in a star pattern to the manual's torque.

After. Lower the car, recheck torque after the first short drive, wash hands, record in the logbook.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor.

Ask a qualified expert. Brake repairs, wheel bearings and steering parts affect lives. At this level you inspect and report; a qualified mechanic or a GhIE-registered engineer must approve and check any brake repair. Never road test a car whose brakes you doubt.

Tyre pressure

  • Check pressure monthly and when the tyres are cold (the car has not been driven for about three hours). Check the spare too.
  • Use the pressure on the tyre information label (often on the driver's door pillar) or in the manual. Do not use the number moulded on the tyre's side; that is the maximum the tyre can hold.
  • Underinflation is the leading cause of tyre failure. A tyre that is too soft wears the edges, overheats and can burst.

Tread, damage and age

Tyres have small raised bars (treadwear indicators) in the grooves; when the tread is level with them, the tyre must be replaced. Replace tyres with cuts, cracks, bulges or uneven wear. Ghana has new Road Traffic Regulations, 2026 (L.I. 2519), reported in the press. The tyre rules in them (tread, age) were not verified: the gazetted text was not read. Press reports of a police explanation mention a tyre age limit, but this is not verified against the text. The status of the older Road Traffic Regulations, 2012 (L.I. 2180) is also not verified, so no tread or age number is printed here as law. Ask DVLA or the National Road Safety Authority for the current rule. Until then, follow the wear indicator and the maker's advice, and replace any damaged tyre.

Change a wheel step by step

Wheel change

  1. Park on level, firm ground. Handbrake on, gear in Park or low. Switch off.
  2. Chock the wheel diagonally opposite the one you will remove.
  3. Take off the wheel cover. Slightly loosen each wheel nut (half a turn) while the wheel is still on the ground.
  4. Place the jack at the jack point in the manual and lift until the tyre is just off the ground.
  5. Place a jack stand under the strong point. Do not put any part of your body under the car.
  6. Remove the nuts. Lift the wheel off and lay it flat nearby. Check the studs for damage.
  7. Fit the new wheel. Screw on the nuts by hand until snug.
  8. Lower the car until the tyre touches the ground, then tighten the nuts in a star (criss-cross) pattern.
  9. Lower the car fully, remove the jack and chocks, and use the torque wrench to the figure in the manual, again in a star pattern.
  10. Check the pressure in the fitted wheel. Record the work in your logbook.
  11. After the first short drive, check that the nuts are still tight. Tell the customer to do the same.

Brakes: what you inspect

Brake pads press on discs (or shoes on drums) to stop the wheel. Pads wear out. Many sources say plan to replace pads when the friction material is about 3 mm thick, but limits vary, so the workshop manual is the authority. Signs of worn brakes:

  • A high squeal from a wear indicator;
  • A grinding noise, which means metal on metal and is urgent;
  • A longer stopping distance, the car pulling to one side, or a shaking pedal;
  • A soft or sinking pedal, or a fluid level that keeps dropping.

Squealing can also come from damp or surface rust, but if it continues in dry weather, have the brakes checked.

Your brake check (look and report)

  1. Press the pedal with the engine off, then with it running. It should feel firm and not sink.
  2. Check the fluid level in the reservoir.
  3. With the wheel off (and the car on stands), look at the pad edge: how much material is left? Look at the disc surface: deep grooves or a rusty rim?
  4. Look for fluid wet on the inside of the tyre or on the caliper.
  5. Write what you saw and report it to your instructor. Do not take apart a brake at this level.

Tyre numbers

A tyre label says 32 psi (example). A tyre gauge reads 26 psi cold. (1) By how much is it low? (2) Is it safe to drive on? (3) What is the likely wear pattern if the car runs like this for months?

Tyre survey

Look at the tyres on three vehicles in your street. Write the tread condition, any damage and whether they look soft. Do not touch another person's vehicle without asking.

Check yourself: Unit 4

  1. Where do you find the right tyre pressure?
  2. In what pattern do you tighten wheel nuts?
  3. A brake pad grinds. What do you do?
06

Unit 5 · Battery, charging and cooling basics

No spark, no start. No coolant, no engine. Learn these two systems well because they break most often.

Competency standard

Learning outcome Performance criteria — the trainee…
5.1 Care for the battery checks, cleans and secures the battery and terminals safely
5.2 Jump start correctly connects and removes leads in the right order
5.3 Read battery voltage uses a multimeter to read resting and running voltage
5.4 Check the cooling system checks coolant, hoses, cap, belt and fan safely

Range. 12-volt lead-acid batteries; passenger cars, pickups and minibuses. Evidence. Observation; readings in the logbook.

Tools and items for this unit

Every item is named here and defined. Sizes are typical; the maker's plate or the vehicle manual rules. The standard English trade name is used, with other common names in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item What it is and what it does Type or size (typical) Care or safety Also called
Battery (12 V lead-acid) A box of acid and lead plates that stores electricity to start the engine and run the lights. Rated in volts and amp-hours (Ah); size by vehicle Gives off hydrogen; keep sparks away; wear glasses. no other common name found
Battery terminal, clamp, earth strap and hold-down The terminal is the post. The clamp grips it. The earth strap joins the negative to the body. The hold-down stops the battery moving. Lead posts; the positive is usually slightly bigger Remove negative first, refit it last. battery post
Jump leads Two heavy cables with clamps that connect a good battery to a flat one. Thicker cable is better; length about 2 to 4 m (typical) Check the insulation; a wrong order can cause sparks. jumper cables, booster cables
Wire brush and baking soda paste The brush cleans crust from posts. Baking soda and water neutralises acid crust. A battery-post brush or a small stiff wire brush Keep the paste out of the cells. terminal brush
Hydrometer or battery tester The hydrometer reads acid strength by floating a bulb in the cell fluid. A battery tester gives a quick health reading. Hydrometer is for flooded cells with removable caps only Acid is harmful; use glasses and gloves. specific-gravity tester
Alternator Driven by a belt, it makes electricity when the engine runs and recharges the battery. Bolted to the engine Do not touch while running. generator (old term)
Radiator cap and coolant The cap holds the system pressure. Coolant is water plus antifreeze that carries heat and protects against corrosion. Use the type the manual says; a 50:50 mix is common (see Appendix B) Poisonous and sweet-tasting. Keep from children and animals. antifreeze; pressure cap
Cooling fan A fan that pulls air through the radiator when the car is slow or stopped. Electric or belt-driven. Often electric Keep hands away; some fans start without warning. radiator fan

Parts and safety: Battery and alternator

Battery and alternator Battery and alternator with numbered parts 1 2 3 4 5 6 7 8
Battery and alternator. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Battery case and cells Stores electricity; contains acid Gives off hydrogen: no sparks; glasses and gloves
2 Positive terminal (+) Feeds power to the car Remove negative first, refit last
3 Negative terminal (-) Connects to the body (earth) Never let a spanner touch the body and positive together
4 Hold-down clamp Stops the battery moving Check tight
5 Earth strap Joins the negative to the body Clean, tight
6 Alternator Makes electricity when the engine runs Do not touch moving parts
7 Crank pulley Drives the belt Keep clear while running
8 Drive belt Turns the alternator Look for cracks and shine

Safety protocol: Battery and alternator

Before. Engine off, key out. Wear glasses and gloves. Remove rings and watches. Look for cracks, leaks, a bulging case. Do not work on a frozen, cracked or leaking battery.

While you work. Remove negative first. Keep sparks and flames away. Clean crust with a brush and baking soda paste, keeping it out of the cells. Never lean over the battery.

After. Refit negative last, tighten, grease the posts. Wash hands. Record voltage and date. Report a cracked or leaking battery.

Emergency. Acid in eye: rinse with clean water for several minutes and call 112 or go to a clinic. Fire: use the extinguisher if safe; call 112.

Parts and safety: Cooling system

Cooling system Cooling system with numbered parts 1 2 3 4 5 6 7 8
Cooling system. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Radiator Gives heat from the coolant to the air Fins bend easily: clean gently
2 Radiator cap Holds pressure in the system Never open hot
3 Upper hose Brings hot coolant from the engine Look for cracks and bulges
4 Lower hose Returns cooled coolant Soft or collapsed hose: replace
5 Water pump and fan belt side Pushes the coolant round Keep clear when running
6 Thermostat housing The thermostat opens when warm Replace with the right rating
7 Coolant reservoir Holds spare coolant (MIN, MAX) Coolant is poisonous; keep from animals
8 Cooling fan Pulls air through the radiator May start without warning: hands away

Safety protocol: Cooling system

Before. Engine cold. Wear gloves and glasses. Look only at Level 1: do not open the system.

While you work. Check level at the reservoir. Do not open the cap hot. If the gauge goes high on the road, pull over, switch off, let it cool. Do not pour cold water on a hot engine.

After. Close the cap and the bonnet. Wipe spills (coolant is poisonous). Record the level and any leak.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor. Scald: cool under running water; swallowed coolant: seek medical help at once.

Safety protocol: jump start

Before. Both batteries 12 V, not frozen, cracked or leaking. Both cars off, handbrakes on. Glasses and gloves, no rings.

While you work. Red to dead positive, red to good positive, black to good negative, last black to bare metal away from the battery. Never lean over the battery. Remove leads in exact reverse order.

After. Remove leads in reverse order, run the engine, report a battery or alternator fault.

Emergency. Call 112 for serious injury, fire or poisoning. Give first aid only if trained. Stop the work, make the vehicle safe, tell your instructor. Battery acid in the eye: rinse with clean water and seek help.

Ask a qualified expert. Car electrics can start fires, and batteries can burst. For anything beyond cleaning, testing and jump starting, ask a qualified mechanic, an auto electrician or a licensed electrician. Never work on airbag circuits. Do not touch the orange high-voltage cables of hybrid or electric vehicles; they are not part of this module.

The battery

A 12-volt battery stores electricity to start the engine and run the lights when the engine is off. The alternator (driven by a belt) recharges it while the engine runs. Keep the top clean, the terminals tight and the battery firmly clamped down.

Safety. The battery gives off flammable hydrogen and contains acid. Wear glasses and gloves, keep sparks away, and do not jump or charge a frozen, cracked or leaking battery.

Clean and secure the battery

Battery care

  1. Switch off everything. Wear glasses and gloves. Remove rings and watches.
  2. Look for cracks, leaks, a bulging case or white or green crust on the terminals.
  3. If you must remove a terminal, take off the negative (black, minus) first and refit it last. This lowers the risk of a short circuit with your spanner.
  4. Clean the clamps and posts with a wire brush. A paste of baking soda and water neutralises acid crust; rinse carefully, keep it out of the cells, and dry.
  5. Refit the clamps and tighten. Smear a little grease on the posts.
  6. Check the hold-down clamp so the battery cannot move.
  7. Record the date and what you found.

Jump start safely

The method below follows common safety guidance; always check the owner's manual of both cars, because some vehicles have special jump points.

Jump start

  1. Check that both batteries are 12 volts and that the dead one is not frozen, cracked or leaking.
  2. Park the good car close, but not touching. Switch both off and put the handbrakes on.
  3. Connect the red (+) lead to the dead battery's positive terminal, then to the good battery's positive.
  4. Connect the black (-) lead to the good battery's negative terminal.
  5. Connect the other end of the black lead to bare metal on the dead car's engine or body, away from the battery, because the battery may release hydrogen.
  6. Start the good car and let it run a couple of minutes. Then start the dead car.
  7. Remove the leads in exactly the reverse order: black from the metal, black from the good battery, red from the good battery, red from the dead battery.
  8. Keep the engine running at least some minutes. If it will not start again later, the battery or alternator is faulty; see Unit 6.

Reading voltage with a multimeter

A multimeter shows volts. Set it to DC volts (20 V range), black probe on the negative, red on the positive.

Reading What it suggests (rule of thumb)
About 12.6 V, engine off, rested for an hour or more Battery fully charged
About 12.0 V or less Battery much discharged
About 13.8 to 14.4 V at idle with the engine running Alternator charging normally
Below about 13.5 V running Alternator may be undercharging
Above about 15 V running Charging system fault

These are rules of thumb. Different batteries and vehicles vary, so ask a qualified auto electrician before you condemn a part.

Cooling system: look, do not open

The cooling system is a loop of coolant through the engine and the radiator, pushed by the water pump, controlled by the thermostat, and helped by a fan. Check, with the engine cold:

  1. Coolant level in the reservoir between MIN and MAX.
  2. Hoses: no cracks, bulges or wet patches; no soft, collapsed hose.
  3. Radiator: no leaks, no mud or leaves blocking the fins.
  4. Belt: tight and not cracked.
  5. Under the car: any green, pink or orange puddle.

If the temperature gauge goes high on the road, pull over, switch off, and let it cool before you look. Do not pour cold water on a hot engine and do not open the cap while hot. Top up only with the coolant type the manual says, mixed as the label says. Remember that coolant is poisonous.

Voltage log

Three cars are tested. Car A: 12.6 V rested, 14.1 V running. Car B: 11.8 V rested, 13.9 V running. Car C: 12.5 V rested, 12.2 V running. For each, say what it suggests and what you would do next.

Voltage survey

With permission, record the resting voltage of the batteries of three vehicles (engine off, several hours rested). Write the car, date and reading. Do not touch the terminals with metal tools.

Check yourself: Unit 5

  1. Which battery terminal do you remove first?
  2. Where does the last black jump lead go?
  3. Why must you not open the radiator cap when the engine is hot?
07

Unit 6 · Simple fault-finding

A mechanic is a detective. Do not change parts and hope. Ask questions, look, test, and only then fix.

Competency standard

Learning outcome Performance criteria — the trainee…
6.1 Interview the customer asks when, where and how the fault shows; records it
6.2 Use your senses safely looks, listens, smells and feels (when safe) for clues
6.3 Work through a simple tree follows a no-start tree and a warning-light list
6.4 Use an OBD scan tool for reading reads codes and records them; does not clear codes to hide a fault

Range. Common faults: no start, slow crank, overheating, rough idle, warning lights, brake or tyre faults. Evidence. Fault-finding records; oral questions.

Tools and items for this unit

Every item is named here and defined. Sizes are typical; the maker's plate or the vehicle manual rules. The standard English trade name is used, with other common names in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item What it is and what it does Type or size (typical) Care or safety Also called
OBD scan tool A device that plugs into the car's diagnostic port and reads the stored trouble codes. Types: simple code reader, Bluetooth dongle with a phone app, and a professional tool. 16-pin socket under the dashboard on most petrol cars Read and record. Do not clear codes to hide a fault. code reader, scanner, diagnostic tool
Torch (work light) A bright, safe lamp for looking under the bonnet and car. LED type, battery or rechargeable Never a naked flame near fuel. flashlight, work lamp
Warning light A symbol on the dashboard. Red means stop or danger; amber means check soon; green or blue means a system is on. See the manual for the symbols Red lights: stop safely. no other common name found
Notebook and job card Where you write the complaint, readings and findings. A5 hard-cover book Date every page. work order, repair order

Parts and safety: OBD scan tool and port

OBD scan tool and port OBD scan tool and port with numbered parts 1 2 3 4 5 6 7
OBD scan tool and port. Numbers on the picture match the table below.
No. Part What it does Safety rule
1 Screen Shows codes and data Write codes down exactly
2 Navigation buttons Move through menus Do not choose the erase option to hide a fault
3 Power and cable Carries data and power Check the cable is not damaged
4 Menu key Choose read, record or erase Read and record only at Level 1
5 16-pin connector Plugs into the car's diagnostic port Push in straight; do not force
6 Pins Carry power and data Keep clean and dry
7 Diagnostic port (under the dashboard) The car's data socket Switch off the ignition before plugging in

Safety protocol: OBD scan tool and port

Before. Engine and ignition off. Check the cable and connector. Park safely with the handbrake on.

While you work. Plug in, switch ignition on, read and record the code. Do not clear a code to hide a fault. Keep the cable away from pedals and the steering column.

After. Switch off, unplug, store the tool dry. Write the code, date and mileage in your logbook.

Emergency. Smoke or burning smell from the port: unplug, switch off, disconnect the battery if safe. For fire, call 112.

Ask a qualified expert. Fault-finding involves fuel, electrics and moving parts. Do not test live circuits beyond what this book shows. For anything unclear, ask a qualified mechanic, an auto electrician or a licensed electrician. Brake, steering and airbag faults go to a qualified mechanic or GhIE-registered engineer.

The method: ask, look, test, fix, check

  1. Ask. What is the problem? When did it start? Is it always there, or only when cold, hot, fast or turning? Was anything changed or repaired recently?
  2. Look. Leaks, loose wires, broken hoses, warning lights, the fuel gauge, the battery.
  3. Listen and smell. Squeal, knock, rattle, grinding, hiss; burning rubber, burning oil, petrol, sweet coolant.
  4. Test. Take a reading or run a simple check to see which of two ideas is right.
  5. Fix the cause, not just the sign.
  6. Check that the fault is gone, and record what you did.

No-start tree

Sign Likely area First check
Nothing happens, no lights Battery or terminals Terminal tight and clean? Battery voltage
Lights dim, slow crank Weak battery or poor connection Voltage; clean terminals
Clicking only Very low battery Voltage; jump start (Unit 5)
Cranks normally but does not fire Fuel or spark Fuel in the tank? Fuel pump sound? Do not test spark at this level
Fires and dies Fuel, air or an immobiliser Warning lights; fuel quality; report
Engine starts, then battery warning light stays on Alternator or belt Belt look; running voltage

Common signs and where to look

Sign Possible causes
Overheating Low coolant, leak, thermostat, fan, belt, blocked radiator
Blue smoke Burning oil
White smoke (thick, sweet) Coolant entering the engine
Black smoke Too much fuel, blocked air filter
Knocking Wrong fuel, low oil, worn engine parts
Pull to one side Tyre pressure, brakes, alignment
Vibration Wheel balance, tyres, worn parts

These are leads, not diagnoses. Confirm with a test before you replace a part, and ask your instructor.

Warning lights

Light What it generally means Action
Red oil can Low oil pressure Stop now, switch off, check oil, get help
Red thermometer Overheating Pull over, switch off, let it cool
Red battery Charging fault Check belt; go straight to a workshop
Red brake Handbrake on, low brake fluid or a brake fault Check handbrake and fluid; do not drive if the pedal is soft
Amber engine Fault stored by the computer Read the code with a scan tool

(Meanings vary a little by car; check the manual.)

OBD scan tool: reading only

Most petrol cars made in recent years have an on-board diagnostics port (OBD-II) under the dashboard. A scan tool reads the stored code. A code has five characters; P means powertrain, and P0 codes are generic ones that mean the same on most makes. A code points you to an area; it does not name the broken part. Clearing a code does not fix the fault and the light will come back. Record the code, read what it means in a reliable list, and do the checks before you replace anything.

Fault-finding drill

  1. Your instructor sets a fault on a training car (for example a loose battery terminal, a low tyre or an unplugged light) without telling you.
  2. Interview the "customer" (the instructor): write the complaint, when it happens and what changed.
  3. Look, listen and smell. Write what you find.
  4. Choose one simple test and do it safely. Record the result.
  5. Say what you think the cause is, and fix it if it is within this module.
  6. Check the fault is gone. Write a short job record.

Ask a mechanic

Ask a mechanic what questions they ask a customer first, and the three faults they see most often. Write the answers.

Check yourself: Unit 6

  1. Name the five steps of the fault-finding method.
  2. Does clearing a code fix the fault?
  3. A car has lights but only clicks when you turn the key. Where do you check first?
08

Unit 7 · Your location, small business and marketing

A good mechanic who cannot be found, or who prices badly, stays poor. Pick a place, count every cost, add a fair profit and keep records.

Competency standard

Learning outcome Performance criteria — the trainee…
7.1 Choose a good location compares locations by customers, rent, safety and permits
7.2 Cost and price a job lists all costs and sets a price with profit
7.3 Market yourself uses WhatsApp Business, signage and referrals
7.4 Keep records records each job, parts and payments
7.5 Know the rules names registration, permits and waste duties

Range. Small service jobs for local customers. Evidence. Costed quotes; one-page plan; job records.

Tools and items for this unit

Every item is named here and defined. Sizes are typical; the maker's plate or the vehicle manual rules. The standard English trade name is used, with other common names in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

Item What it is and what it does Type or size (typical) Care or safety Also called
Receipt book and cash book The receipt book gives the customer a written record. The cash book lists money in and out. Duplicate receipts; an exercise book is a start Ask GRA how long records must be kept. no other common name found
WhatsApp Business profile A free business profile with a catalogue and quick replies. Phone app Do not post a customer's photo without permission. no other common name found
Cost sheet A page that adds up parts, consumables, waste handling, labour, rent and profit for one job. One sheet per job Tell the customer the price before you start. no other common name found

Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer before you act on any legal, licence or registration matter. For tax, VAT, PAYE and SSNIT, check with GRA or a qualified accountant before you act. For insurance and loans, ask your bank or a licensed financial adviser. For the safety of any workshop, ask a qualified mechanic or a GhIE-registered engineer.

Where to work

Idea Why it can pay Watch out
Mobile service (you go to the customer) Low rent; customers pay for convenience Needs a safe, level place and your own tools; never lift without stands
Roadside or garage-cluster spot, such as Kokompe Customers already come for vehicles; master mechanics to learn from More competition; weather; waste rules
Near a taxi, trotro or minibus station Regular customers who need quick service Service must be fast; cash flow
Near a busy road or market Passing trade Rent and permit rules
Near a spare-parts shop Parts nearby Many competitors

Choose by asking: Who drives past? Is the ground level and dry? Is there water, shade, and a safe place to keep tools? Can I keep used oil and waste off the drain? What does the Assembly say?

Small business ideas

  • Mobile oil and filter service, battery test and jump start
  • Tyre pressure, wheel change and tyre safety checks
  • Minibus and taxi routine service contracts
  • Pre-purchase inspection checks for buyers (look-only; give the buyer a written list)
  • Car-care shop: wiper blades, bulbs, filters and oil
  • Apprentice or helper for an established mechanic while you learn

Costing a job

Add up: parts + consumables (rags, gloves, cleaner) + waste handling (used oil container, collection) + your labour + rent or transport, then add a profit. Never price from memory. Tell the customer the price before you start.

Price a service

Example prices: oil GH¢240, filter GH¢45, washer GH¢5, air filter GH¢60, consumables GH¢20, transport GH¢30, your labour for 2 hours at GH¢50 an hour. (1) Total cost? (2) Price for a 25% margin on the price? (3) A customer pays a 50% deposit on the parts. How much is that?

Register and follow the rules

  • Registering a business name at the Office of the Registrar of Companies costs GH¢130, then GH¢70 a year to renew (2026 fees). Your Ghana Card number is your tax number (TIN).
  • The Sekondi-Takoradi Metropolitan Assembly (STMA) gives business operating permits. The 2025 fee for a garage or auto mechanic was not verified; ask STMA.
  • Workplace safety law, the Factories, Offices and Shops Act 1970 (Act 328), covers workshops, and its Factories Inspectorate inspects workplaces; the details that apply to a small garage were not verified. Ask the Labour Department or the Factories Inspectorate.
  • Waste: ask the EPA about used oil and battery rules.
  • A vehicle's roadworthiness certificate comes from DVLA through a designated private vehicle testing station, not from a garage. Do not sell or write a roadworthy sticker. Fees are not verified.

Market yourself

  • WhatsApp Business: a profile with your name, area, services and opening hours; a catalogue of services; a quick reply; a status with before-and-after photos (with the customer's permission).
  • Google Business Profile: list your garage or mobile service so people find you on the map.
  • Signage: a clear sign with your trade, your area and a way to reach you.
  • Referrals: ask taxi drivers and shop owners to send customers; thank them.
  • Portfolio: photos of neat work and a service record sheet you give each customer.

Accessibility

Disability does not stop you from earning in this trade, but safety comes first. The adjustments below are suggested by the author, not sourced: no Ghana source on disability and auto mechanics was found. The Persons with Disability Act 2006 exists; ask the National Council on Persons with Disability or a lawyer about your rights.

Task Notes and adjustments
Diagnosis, reading codes, battery and electrical testing Good bench work for wheelchair users and people with leg injuries: a raised bench with knee space
Customer service, quotes, bookkeeping, parts stock, WhatsApp marketing Workable for most disabilities
Fluid checks, filters, tyre pressure Workable with a stool, low stand or trolley
Hearing-impaired trainees Written job cards and visual signals; no reliance on shouted warnings near a running engine
Visually impaired trainees Customer service, sales and parts work; tactile markers and a talking multimeter (price not verified)
Lifting vehicles, working under cars Needs full mobility and a partner; use team roles

Quote and plan

  1. For a routine oil service, write a full cost sheet and a price.
  2. Write a one-page plan: your location idea, tools you have and need with cost, three services, prices, first customers, registration and permit, and your waste plan.
  3. Write the wording of your WhatsApp Business profile and sign.
  4. Present your plan to the class.
  5. Keep a job record book from today.

Talk to a master

Ask an experienced mechanic how they price jobs, how they find customers and what they wish they had known when they started. Write it down.

Check yourself: Unit 7

  1. Name two costs in a service job besides parts.
  2. Who issues a roadworthiness certificate?
  3. Where can you register a business name?
09

Glossary

Term Meaning
Alternator The part that makes electricity and recharges the battery while the engine runs
Brake disc / pad The disc turns with the wheel; the pads squeeze it to slow the car
Carbon monoxide (CO) A poisonous gas in exhaust, which you cannot see or smell
Chock A wedge that stops a wheel from rolling
Coolant Liquid that carries heat from the engine to the radiator
Competent / Not Yet Competent The two possible results of a CBT assessment
Dipstick A rod that shows the engine oil level
Jack stand A rated stand that holds a lifted vehicle safely
Multimeter A meter that reads volts, amps and ohms
OBD On-board diagnostics: the car's computer and its test port
Sump The oil pan at the bottom of the engine
Torque wrench A wrench that tightens to a set force
Viscosity How thick or thin an oil is
10

Logbook

Copy these pages into an exercise book. Your logbook is part of your assessment evidence.

  • Unit 1: lift and support record; safety checks; garage visit notes
  • Unit 2: engine bay map; manual facts; tool list
  • Unit 3: oil change record; service record; service sheet
  • Unit 4: tyre readings; wheel change; brake check report
  • Unit 5: battery care; jump start; voltage readings
  • Unit 6: fault-finding drill record; mechanic's questions
  • Unit 7: cost sheet; one-page plan; job record book
  • Every homework, dated
11

Self-check quiz

  1. What must support a car before you work under it?
  2. Why must you never run an engine in a closed room?
  3. Why must the radiator cap stay shut on a hot engine?
  4. Where do you find the correct oil grade for a car?
  5. In what order do you loosen, lift, support and tighten when you change a wheel?
  6. Where do you find the right tyre pressure?
  7. What does a grinding noise from the brakes mean?
  8. Which battery terminal do you remove first, and which do you refit first?
  9. Where does the last black jump lead go?
  10. What is a safe way to store used oil?
  11. Does clearing a fault code fix the problem?
  12. Name three costs in a service job and where you register a business name.
12

Appendix A · Bench cards: safety and stop rules

Tear out or copy these two cards and pin them where you work. Label: OFFICIAL where a source is named; the rest is good practice.

Ask a qualified expert. These cards summarise good practice, not a legal duty. For lifting, fuel, battery, electrical or brake work, ask a qualified mechanic or a GhIE-registered engineer, and use a licensed electrician for workshop wiring. For injury or poisoning see a doctor or nurse; in an emergency call 112.

Card 1 · Safety rules before you start

Check Rule
Ground Dry, level, firm. Handbrake on, Park or low gear
Chocks On the wheel diagonally opposite the lifted wheel
Lifting Jack only at the manual's jack points; rated jack stands under strong points; shake test; never under a jack alone
Exhaust Engine runs outdoors or with extraction only
Fuel and fire No flame, no smoking, no grinding near fuel; oily rags in a closed metal bin; extinguisher within reach
Hot parts Radiator cap stays shut until the engine is cold
Battery Glasses and gloves; no sparks; negative off first and on last
Coolant and brake fluid Poisonous; labelled closed containers
Used oil Sealed, labelled drum on a tray; never on the ground or in a drain
PPE Glasses, gloves, overalls, boots; no rings, watches or chains near the battery or moving parts

Card 2 · Stop, do not drive

Stop and refer the vehicle to a qualified mechanic if you see any of these. If the car is a customer's, tell the owner in writing.

  • Brake pedal soft, sinking or going to the floor
  • Brake grinding (metal on metal)
  • Brake fluid leaking, or the fluid level keeps dropping
  • Red oil-pressure, red brake or red temperature light on
  • Steering very loose, heavy or making loud noises
  • A tyre with a bulge, cut, exposed cord or very low tread
  • Loose or missing wheel nuts
  • Fuel smell or a fuel leak
  • Smoke from under the bonnet
  • A vehicle held up on a jack only
13

Appendix B · Bench tables: typical values

Every table is labelled TYPICAL, EXAMPLE or OFFICIAL. The vehicle owner's manual or workshop manual always rules.

Ask a qualified expert. Pressure, torque, brake and battery values affect safety. Use these tables only to check you are in the right area, then take the exact figure from the vehicle's manual. If unsure, ask a qualified mechanic or an auto electrician.

B1 · Pressure units (calculated; exact conversion factor 1 psi = 6.894757 kPa)

psi kPa bar
26 179.3 1.79
28 193.1 1.93
30 206.8 2.07
32 220.6 2.21
35 241.3 2.41
36 248.2 2.48
40 275.8 2.76
44 303.4 3.03

1 bar is 14.5 psi (rounded). These are conversions, not recommended pressures. The label on the car gives the pressure.

B2 · Torque units (calculated; 1 lb-ft = 1.3558 N.m)

lb-ft N.m
76 103.0
88 119.3
100 135.6
120 162.7

To go the other way: 100 N.m is about 73.8 lb-ft.

B3 · Wheel nut torque: TYPICAL only

Published general guides give about 76 to 100 lb-ft (about 103 to 136 N.m) for many passenger cars with M12 studs, and higher for pickups and trucks, but the guides disagree and the nut seat and thread pitch matter. Use the figure in the owner's manual. Torque values for other bolts are not verified here; ISO 898-1 and SAE J429 are the bolt-grade standards a table should be built from (international standards; check the vehicle manual).

B4 · Brake fluid grades (minimum boiling points, OFFICIAL, USA regulation FMVSS 116; international reference)

Grade Dry boiling point minimum Wet boiling point minimum Note
DOT 3 205 C 140 C Glycol type
DOT 4 230 C 155 C Glycol type
DOT 5.1 260 C 180 C The regulation text treats 5.1 under DOT 5 limits; glycol type
DOT 5 260 C 180 C Silicone type: never mix with the others

Use the grade on the reservoir cap or in the manual. This is a USA regulation used as an international reference; check against the Ghana Standards Authority text when it is read. Many sources say to change brake fluid about every two years, but the maker's schedule rules.

B5 · Battery voltage, 12 V lead-acid, TYPICAL

Rested reading (engine off, 1 hour or more) State
12.6 V or more Full
about 12.4 V about three-quarters
about 12.2 V about half
about 12.0 V about one-quarter
11.9 V or less flat; recharge and test
Engine running, idle: 13.8 to 14.4 V Charging normally

Sources differ by about 0.1 V per step, so use these as a ladder, not as a verdict. Check with a battery maker or an auto electrician.

B6 · Engine oil label, TYPICAL

Label part Meaning
5W Flows like a thinner oil when cold (W is winter)
30 Thickness when hot
API letters Service rating; use the one in the manual

B7 · Coolant, TYPICAL

Use the coolant type in the manual. Mixing different colours or types is not safe unless the maker says so. A 50 percent coolant and 50 percent water mix is common; follow the label on the container. Coolant is poisonous.

B8 · Common blade-fuse colours, TYPICAL (international practice; not verified here)

Colour Rating
Tan 5 A
Brown 7.5 A
Red 10 A
Blue 15 A
Yellow 20 A
Clear or white 25 A
Green 30 A

The number printed on the fuse is the rating. Never fit a higher fuse than the box lid says.

14

Appendix C · Tyre decoder card

A tyre tells you its size, its load class, its speed class and its birth date. Learn to read it.

Ask a qualified expert. Tyre choice and age affect lives. When unsure, ask a qualified mechanic or a tyre specialist. Maker advice on tyre age differs, so check the vehicle maker.

Example sidewall: 205/55 R16 91V (example). Read it left to right.

Part Meaning in the example
205 Width of the tread in millimetres
55 Height of the sidewall as a percent of the width (aspect ratio)
R Radial construction
16 Rim diameter in inches
91 Load index: a code, not a weight; look it up in a load chart
V Speed rating letter: the highest speed the tyre can carry, not a target
DOT code, last four digits Week then year of manufacture: 1121 is week 11 of 2021

Worked sum (checked by script). Sidewall height = 205 x 0.55 = 112.75 mm. Rim = 16 x 25.4 = 406.4 mm. Overall diameter = 406.4 + 2 x 112.75 = 631.9 mm.

Pressure: use the label on the door pillar or the manual, cold, monthly. Tyre age: maker advice differs, and the Ghana rule is not verified (see Appendix J).

15

Appendix D · Warning lights and what to do

Colour code: red means stop safely; amber means check soon; green or blue means a system is on. Meanings vary a little by car; the manual wins.

Light Usual meaning What you do
Red oil can Low oil pressure Stop, switch off, check oil, get help
Red thermometer Overheating Pull over, switch off, let it cool
Red battery Charging fault Check belt; go to a workshop
Red brake or (!) Handbrake, low fluid or a brake fault Check handbrake and fluid; do not drive on a soft pedal
Red airbag or seatbelt Safety system fault Do not touch airbag parts; refer to a qualified mechanic
Amber engine Fault stored by the computer Read the code (Appendix F)
Amber ABS Anti-lock braking fault: normal brakes may still work Refer to a qualified mechanic
Amber tyre-pressure A tyre is low (TPMS: tyre pressure monitoring system) Check all four tyres cold
Amber glow-plug coil (diesel) Glow plugs warming Wait until it goes out before starting
Amber fuel pump or low fuel Low fuel Fill up; do not run dry
16

Appendix E · Six fault charts

Follow the first line that fits. These are leads, not diagnoses. Test before you replace anything.

Ask a qualified expert. Fuel, electrical, brake and steering faults can be dangerous. Do the checks shown and no more; refer the rest to a qualified mechanic, an auto electrician or a GhIE-registered engineer.

E1 · Will not crank (nothing or a click)

Step Check If yes If no
1 Dash lights come on? Go to 2 Check battery terminals and voltage
2 Lights go dim when you turn the key? Weak battery: voltage test, jump start Go to 3
3 Only a click? Very low battery or poor terminal: clean and test Gear in Park or neutral? Check, then refer

E2 · Cranks but does not start

Step Check Lead
1 Fuel in the tank? Gauge honest? Fill up
2 Can you hear the fuel pump hum for a moment on key on? No hum: refer (fuse and relay are for the next level)
3 Warning light or immobiliser light flashing? Key problem: refer
4 Recent fuel from a roadside seller? Bad fuel possible: refer to a qualified mechanic

E3 · Overheating

Step Check
1 Engine off, cool. Coolant level in the reservoir between MIN and MAX?
2 Leaks, wet hoses, puddles under the car?
3 Fan turns when the engine is hot?
4 Belt tight and not cracked?
5 Radiator fins blocked with mud or leaves?
6 Still hot: refer. Do not keep driving.

E4 · Smoke colours

Colour Likely lead
Blue Burning oil
White, thick, sweet smell Coolant entering the engine
Black Too much fuel or blocked air filter
Thin white on a cold morning Often water vapour and normal

E5 · Brakes

Sign Action
Squeal, dry weather, keeps on Report: inspect pads
Grinding Stop driving, refer
Soft or sinking pedal Stop driving, refer
Pulls to one side Report; check tyre pressure first
Pedal shakes Report: could be disc or wheel balance

E6 · Pulling and vibration

Sign First check
Car pulls to one side Tyre pressure on all four
Vibration at speed Tyre damage, lost balance weight, loose wheel nuts
Steering wheel shakes under braking Report: brake or suspension
Noise when turning Report: suspension or steering part
17

Appendix F · OBD scan card

Read and record. Do not clear the code to hide the fault. A code points to an area; it does not name the broken part.

Ask a qualified expert. Do not replace parts on a code alone. For anything beyond reading and recording, ask a qualified mechanic or an auto electrician.

Anatomy of a code (for example P0301).

Position Meaning
Letter P powertrain, B body, C chassis, U network
0 as the second character A generic code that means the same on most makes; other digits can mean maker-specific. Sources differ on the other digits, so check the standard (SAE J2012 and ISO 15031-6) before you rely on them
Last digits Identify the system and fault

The P01xx to P09xx groups run: fuel and air; ignition and misfire; emissions; idle and speed; computer outputs; transmission. A new seven-character format is mentioned by some sources; it was not verified.

Code Usual title (typical) First check
P0171 System too lean, bank 1 Air leaks, dirty air filter
P0172 System too rich, bank 1 Air filter, leaks of fuel
P0300 Random misfire Plugs, coils, fuel quality
P0301 Cylinder 1 misfire detected Plug and coil on cylinder 1
P0420 Catalyst efficiency below threshold, bank 1 Exhaust leaks and misfires first
P0442 Small evaporative leak Fuel cap
P0128 Coolant thermostat below temperature Thermostat, coolant level
P0113 Intake air temperature sensor high Sensor connector
P0335 Crankshaft position sensor circuit Sensor connector; refer
P0562 System voltage low Battery and charging (Unit 5)

Titles are typical; read the exact wording on your scan tool. Many cars sold in Ghana are imports, and generic codes match across makes but maker codes do not.

18

Appendix G · Forms to copy

Photocopy or copy into an exercise book. Written estimates are good practice; whether Ghana law requires them was not verified.

G1 · Vehicle check-in and inspection sheet

Field Entry
Owner and contact (no phone numbers in this book; write yours here)
Number plate, make, model
Mileage and fuel level
Complaint, in the customer's words
When did it start; hot or cold; fast or slow
Existing damage (mark a sketch)
Valuables left in the car
Tyre pressures (cold), four plus spare
Lights, wipers, horn, handbrake
Fluid levels: oil, coolant, brake, screen wash
Leaks seen
Warning lights on
Customer signature and date

G2 · Service record

Date Mileage Work done Parts Advice next visit Signature

G3 · Customer sign-off

Item Tick
Price told before work
Deposit agreed
Work done explained
Old parts shown if asked
Wheel nuts rechecked after the first drive: told the customer
Used oil and waste handled correctly
19

Appendix H · Minor service checklist and decisions

The maker's schedule governs. The kilometre figures are not printed here because they depend on the vehicle: not verified.

Ask a qualified expert. For anything about brakes, fuel, steering or electrics, ask a qualified mechanic. These lists are for routine care only.

  • Engine oil level and condition; oil and filter changed on time
  • Coolant level, hoses, belt
  • Brake fluid level; pad look (report)
  • Tyre pressures, tread, damage; spare checked
  • Wheel nuts torqued to the manual
  • Lights, wipers, horn, handbrake
  • Battery terminals clean and tight; voltage read
  • Air filter looked at
  • Leaks under the car
  • Record written and customer advised

Hot and dusty conditions. Heat, dust, harmattan and rough roads are harder on filters, batteries, coolant, rubber and suspension. Use the maker's "severe use" schedule if one is listed. Check filters, coolant and belts more often. (Author's advice; no Ghana table was found.)

Decide Rule of thumb Action
Tyre cut, bulge or cord showing Unsafe Replace
Brake pedal soft Unsafe Do not drive, refer
Pad 3 mm or thinner (typical warning, Source: Brembo Pad Wear) Plan replacement Report
Battery below about 12 V rested Discharged Charge, test
Belt cracked or shiny Worn Report for replacement
20

Appendix I · Ten mistakes beginners make

  1. Over-tightening the drain plug and stripping the sump thread. Use the torque from the manual.
  2. Reusing the old crush washer. It may leak.
  3. Fitting the wrong oil grade or filter. Check the manual.
  4. Not torquing the wheel nuts. They can come loose.
  5. Forgetting to recheck wheel nuts after the first short drive.
  6. Replacing a part without testing, then the fault comes back.
  7. Clearing a code and sending the car away.
  8. Mixing coolant types.
  9. Opening a hot radiator cap.
  10. Leaving a rag or tool in the engine bay.
21

Appendix J · Ghana rules and facts, last checked 20 November 2026

Each line says what is known, how sure we are, and who to ask. Press reports are not the law.

Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer or the named office before you act on any law, licence or permit matter.

Topic What is known Status Ask
Road Traffic Regulations 2026 (L.I. 2519) Press report new regulations including offences for unsafe or worn tyres, no warning triangle and washing or repairing a vehicle on the road Press only; text and penalties not verified The Ministry of Transport or DVLA
Repairing a vehicle on the road Reported as an offence Not verified; do not do roadside work in a lane of traffic DVLA
Roadworthiness certificate From DVLA via a designated private testing station Official; fees not verified DVLA
Testing centres DVLA closed six private centres in April 2026 for issuing reports without proper inspection Press report DVLA
Used-vehicle import standard The Ghana Standards Authority runs a vehicle homologation and conformity programme under GS 4510; the age limit is reported differently by different outlets Age limit not verified; read the GSA notice The Ghana Standards Authority
Garage waste The EPA warned in 2013 that garage waste is a hazard; the Environmental Protection Act 2025 (Act 1124) replaced the old Act Used oil rules not verified EPA Western Region, Takoradi
Workshop safety law Factories, Offices and Shops Act 1970 (Act 328) Details not verified Factories Inspectorate or Labour Department
Fuel quality Roadside "table-top" fuel can be poor; buy from licensed stations Advice only The National Petroleum Authority
Fake parts Counterfeit brake pads, filters and plugs are reported on the market Not verified; check packaging and the part number, and buy from a trusted shop The dealer or the Ghana Standards Authority
22

Appendix K · Formula card

All numbers are examples and were checked by script.

Job Formula Worked example
Fuel use litres used / km driven x 100 = L per 100 km 40 L over 480 km = 8.33 L per 100 km; 480 / 40 = 12.0 km per litre
Fuel cost per km price x litres / km GH¢20 per L (example) x 40 / 480 = GH¢1.67 per km
Tyre diameter rim x 25.4 + 2 x width x ratio 631.9 mm for 205/55 R16
Ohm's law V = I x R 12 V across 4 ohm = 3 A
Power P = V x I 12 V x 3 A = 36 W
Coolant mix total x 0.5 6 L system at 50:50 = 3 L coolant + 3 L water
Pressure shortfall label - gauge 32 - 26 = 6 psi
23

Appendix L · Tools and Items Glossary

A. Tools and instruments; B. Materials and fluids; C. Parts and systems. Other common names are in the last column. Local names differ from town to town, so use the standard name given here and show the picture.

A · Tools and instruments

Item Type or size (typical) What it is and what it is used for Care Also called
Breaker bar Long, 1/2 inch drive Loosens tight bolts Not for final tightening breaker handle, power bar
Combination spanner Metric, 8 to 19 mm Undoes nuts and bolts Pull towards you wrench, open-end and ring spanner
Creeper A low wheeled board Lets you lie under a raised car on stands Keep clear of walkways no other common name found
Dipstick Rod with marks Reads oil level Wipe first oil level stick
Drain pan Sized to the sump Catches used oil Label for used oil only oil pan, catch pan
Feeler gauge Thin steel blades Measures small gaps Keep clean thickness gauge, feeler blade
Funnel Plastic Guides fluid One per fluid filling funnel
Grease gun Hand pump Puts grease into fittings Wipe nipples no other common name found
Jack stand Rated in tonnes Holds a lifted car Inspect before use axle stand, safety stand; lifting jack
Jump leads Heavy cable, 2 to 4 m Connect a good battery to a flat one Check insulation jumper cables, booster cables
Multimeter Digital Reads volts, ohms Use as shown DMM, volt-ohm meter, avometer
Oil filter wrench Strap, cup or chain Removes stuck filter Keep pan under filter strap wrench
Pliers Long-nose, locking, slip-joint Hold and grip Right type for the job pincers
Ratchet and sockets 1/4, 3/8, 1/2 inch drive Turn nuts Right size ratchet handle
Screwdrivers Phillips, flat, Torx Turn screws Right tip driver
Tread depth gauge Pencil, dial, digital Measures groove depth Check accuracy tread gauge
Tyre levers Steel bars Pry tyre from rim (for workshops) Not for beginners no other common name found
Tyre pressure gauge Pencil, dial, digital Reads pressure Check accuracy tire gauge, tyre gauge
Torque wrench Click type Tightens to a set force Set to lowest after use torque spanner
Trolley jack Rated in tonnes Lifts a car Never alone floor jack, garage jack; lifting jack
Wheel chock Wedge Stops rolling Use two wheel wedge, wheel stop
Wire brush Battery-post type Cleans crust Gloves terminal brush

B · Materials and fluids

Item What it is and what it is used for Care Also called
Absorbent Sand or sawdust to soak spills Bin it no other common name found
Baking soda Neutralises acid crust Not in cells no other common name found
Brake fluid Passes pedal force to brakes Keep closed no other common name found
Brake cleaner Spray solvent that cleans brake parts Ventilate; flammable no other common name found
Coolant Antifreeze plus water Poison antifreeze
Degreaser Cleans oil and grease Gloves no other common name found
Engine oil Lubricates Used oil is waste motor oil
Gear oil and ATF Lubricate gearbox and differential (ATF is automatic gearbox fluid) Use the type in the manual no other common name found
Grease Thick lubricant for joints Wipe off excess no other common name found
Penetrating oil Loosens rusty bolts Flammable no other common name found
Power-steering fluid Fluid for hydraulic steering Type per manual no other common name found
Rags Wipe Metal bin shop cloth, wipe
Screen wash Cleans the windscreen Keep from children no other common name found

C · Parts and systems

Item What it is and what it does Where to find it Also called
Air filter Cleans intake air In a box on the engine air cleaner element
Alternator Makes electricity Belt-driven, on the engine generator (old term)
Battery Stores electricity Under the bonnet or in the boot no other common name found
Brake disc, pad, caliper Slow the wheel Behind the wheel brake rotor
Brake master cylinder Pedal-operated pump On the bulkhead brake master
Cooling fan Pulls air Behind the radiator radiator fan
Drive belt Turns the alternator Front of the engine fan belt, serpentine belt
Fuse box Holds fuses Under dash or bonnet blade fuse
Hose Carries coolant Radiator to engine no other common name found
Oil filter Cleans oil On the engine block no other common name found
Radiator and cap Cools coolant; cap holds pressure Front of the car no other common name found
Spark plug Makes the spark in a petrol engine In the cylinder head sparking plug
Starter motor Turns the engine to start Beside the gearbox starter motor, self-starter
Sump Oil pan Bottom of the engine no other common name found
Thermostat Valve that opens when warm Engine coolant outlet no other common name found
Tyre Rubber on the wheel Wheels no other common name found
Water pump Pushes coolant Front of the engine no other common name found
24

Appendix M · Abbreviations and index

Short Meaning
ABS Anti-lock braking system
API American Petroleum Institute (oil service rating)
ATF Automatic transmission fluid
DOT Brake fluid grade label (Department of Transportation, USA); also the tyre code prefix
DTC Diagnostic trouble code
ECU Engine control unit (the engine computer)
MIL Malfunction indicator lamp (the engine light)
OBD On-board diagnostics
PPE Personal protective equipment
TPMS Tyre pressure monitoring system
TWI Treadwear indicator
V Volt (also the speed rating letter in a tyre code)

Where to find it. Jack stands: Unit 1 and Appendix A. Oil change: Unit 3. Tyre decoder: Appendix C. Wheel change: Unit 4. Battery: Unit 5 and Appendix B. Fault charts: Appendix E. OBD: Unit 6 and Appendix F. Forms: Appendix G. Ghana rules: Appendix J.

25

Further reading and sources

Best next reads: the owner's manual of any car you work on; the Hub's Motorbike and Tricycle Servicing and Refrigeration and AC Basics for the related trades; then Auto Mechanics Basics Level 2.

What this module does not cover: engine rebuilds, gearbox and clutch repair, brake repair, steering and suspension repair, airbags, hybrid and electric vehicles, car air-conditioning gas, motorbikes, and Ghana parts and garage-rent prices (not found reliably; ask local dealers). DVLA fees and the NVTI trade-test grades were not verified.

Every source used in this manual is listed, with links, in the Teacher Copy.

One application of the Cold-Start Learning Kit, which stays general-purpose and can build a guide on any topic in any field. Written in CTVET format; not CTVET's own Automotive Mechanic curriculum.