← All training manualsElectronics Repair and Soldering Level 3 · read-onlyGet the PDF with Teacher Copy (GH¢50)
Level 3 · Advanced · CTVET formatTrainee Manual

Electronics Repair and Soldering Level 3

Read the drawing, trace the signal, set your standards, and build a repair business that keeps honest books and earns trust.

A soldering iron, a circuit board and a multimeter on a repair bench A bench with a blue circuit board in the middle holding a few small parts. A soldering iron rests on the board with a small curl of smoke rising. To the left a digital multimeter with a round dial and two probes. To the right a small radio with an antenna and a hand-held torch ready to be mended. 4.7 TEST FIRSTSOLDER NEATLYMEND AND SELL
Trainee name
Training centre
Start date
Instructor
Prepared by De-Graft Afful · Version 1.1.0 · November 2026
01

About this module

At this level you work with little supervision on low-voltage work, you handle problems that are not routine, you teach others, and you can run a business. With that comes more responsibility: for safety, for honest advice and for your customers' money.

Who it is for. Trainees who have completed Electronics Repair and Soldering Level 2, or who can show the same skills and who understand the permission ladder. Aged 18 or over. National Proficiency II leads to National Certificate I in the national framework. This module is an advanced module comparable to that level; it is not a CTVET curriculum and does not carry accreditation.

CTVET status. Electronics competency-based courses were listed at NP I and NP II with dates that ended in April 2025; current status is not verified. Ask CTVET or the regional TVET Service office for the current standard before you claim any qualification.

Bridge from Level 2: what you already know

  • The permission ladder: Tier A alone, Tier B supervised, Tier C never
  • Isolate, wait, discharge, test dead; the first power-up is not yours
  • Component tests; board and track repair; first SMD look
  • Power-supply blocks, linear and switch-mode; bench supply with current limit
  • Battery care; inverter and UPS battery-side checks
  • Radio, amplifier and TV block logic
  • Quoting, guarantee, break-even

How the module works

Each unit has learning outcomes, performance criteria, a range and evidence. You are judged Competent or Not Yet Competent by being watched at work, by your repairs and records, by answering questions and by your logbook. Each unit ends with homework and Check yourself; the module ends with a 12-question quiz and a capstone.

02

Unit 1 · Schematics, service manuals and signal tracing

A circuit diagram is a map. A service manual is a guide who knows the road. With both, you do not guess.

Competency standard

Learning outcome Performance criteria — the trainee…
1.1 Read a schematic names the symbols, follows the power and the signal, and marks test points
1.2 Use a service manual finds the block diagram, the part list and the test voltages for a fault
1.3 Trace a signal uses half-splitting to find the failed stage
1.4 Use the scope safely sets probe, ground and timebase correctly and reads a simple trace
1.5 Record and report writes a repair report that another technician can follow

Range. Low-voltage boards (Tier A); mains boards dead and supervised (Tier B). Evidence. Observation; marked diagrams; repair report.

Ask a qualified expert. A scope's probe ground is connected to mains earth on many bench scopes, so clipping it to the wrong point on a live board can cause a short or danger. Never use a scope on a mains-powered unit without a qualified technician. For electrical work ask an Energy Commission-certified electrician; for injury see a doctor or nurse.

Reading a schematic

  • Symbols stand for parts: a zig-zag or box for a resistor, two lines for a capacitor, a triangle with a bar for a diode, a circle with a letter for a transistor.
  • Lines are wires. A dot where lines cross means joined; no dot means not joined.
  • Power usually runs from top to bottom; signals usually from left to right.
  • Reference marks such as R12, C5 and D3 match the printing on the board and the parts list.
  • Test points (TP1, TP2) show where to measure and what you should find.

The service manual

A service manual usually has: a block diagram, the circuit diagram, a parts list with values and ratings, test voltages, and notes on adjustment and safety. Always use the manual for the model you have. Voltages and values in a different model can mislead you. Where no manual exists, draw your own diagram as you trace the board.

Half-split fault finding

  1. Draw the blocks from input to output.
  2. Pick the middle of the chain. Measure there.
  3. If the signal is good, the fault is after that point; if bad, before.
  4. Repeat on the remaining half. After three or four steps you have the stage.
  5. Within the stage, test the parts out of circuit.

Voltage divider (a useful circuit)

Two resistors in series divide a voltage: V out = V in × R2 ÷ (R1 + R2). Many boards use a divider to set a voltage or feed a sensor.

Divider

  1. A 12 V supply feeds R1 = 6.8 kΩ in series with R2 = 4.7 kΩ. What is the voltage across R2?
  2. R1 and R2 are both 10 kΩ with 12 V in. What is the voltage across R2?
  3. On the bench the voltage across R2 in question 1 measures 8 V. What could be wrong?

The oscilloscope in brief

An oscilloscope draws a graph of voltage against time. The vertical scale is volts per division; the horizontal scale is time per division.

  • Most probes are 10X: set the scope channel to match, and compensate the probe with the scope's test signal before use.
  • Connect the probe ground clip to a ground point close to the test point. A long ground lead can add false ringing on fast signals.
  • Ground on a bench scope is earth. Clipping it to a point that is not at ground can create a short.
  • For this course, use the scope on low-voltage boards on a bench supply, and on audio and logic signals. Mains-side measurements are for qualified technicians with isolation equipment.
Photograph of a digital oscilloscope showing a sine waveA real digital storage oscilloscope seen from the front on a bench: a colour screen showing a yellow sine wave on a grid, vertical and horizontal scale knobs, a trigger section, four channel input connectors with one probe cable plugged into channel 1, and a power button at the lower left. Numbered 1 to 7.1234567
A real digital oscilloscope showing a sine wave, with one probe plugged into channel 1. This model has four channels. Numbers match the table. (Photo: Draconichiaro, CC BY-SA 4.0)
No. Part What it does Safety rule
1 Screen with grid Shows voltage (up) against time (across) Read the volts and time settings on the screen before you read the wave
2 Volts per division knob Sets how many volts each square stands for Start on a high range, then reduce
3 Time per division knob Sets how much time each square stands for Choose slow for audio and fast for switching signals
4 Trigger level knob Holds the picture steady by starting the sweep at the same point A wrong trigger gives a false picture
5 Channel 1 input connector Where the probe plugs in; its outer ring is the scope's earth Never clip the probe ground to a live point
6 Probe cable Carries the signal from the circuit to the scope Do not use a cable with cracked insulation
7 Power button Switches the scope on Use an earthed plug and a good mains lead
Bench oscilloscope front panel with every control numbered Front panel of a two-channel oscilloscope: grid screen with a square wave trace, volts per division knob, time per division knob, trigger level knob, vertical position knob, two channel input sockets, a probe compensation terminal and a power button. 1 2 3 4 5 6 7 8 9 Parts (numbers match the drawing) 1 Screen with a grid (divisions) 2 Volts per division knob 3 Time per division knob 4 Trigger level knob 5 Vertical position knob 6 Channel 1 input (BNC) 7 Channel 2 input (BNC) 8 Power button 9 Probe compensation terminal
A two-channel oscilloscope. Controls differ between makes: read your own manual. Source: author's drawing; Saleae Oscilloscope.
No. Part What it does Safety rule
1 Screen with grid Shows voltage (up) against time (across), one square being a division Do not leave a bright dot still on an old screen
2 Volts per division Sets how many volts each division means Start on a high range, then reduce
3 Time per division Sets how much time each division means Slow for mains-frequency or audio, fast for switching
4 Trigger level Holds the picture steady by starting the sweep at the same point A wrong trigger makes a false picture
5 Vertical position Moves the trace up or down
6 Channel 1 input Where probe 1 plugs in; its ground is the scope's earth Never clip the ground to a live point
7 Channel 2 input Second probe Both grounds are joined: never two different grounds
8 Power button Switches on Use an earthed plug
9 Probe compensation terminal A small test signal to adjust the probe Do it before first use
Oscilloscope probe with every part numbered A 10X oscilloscope probe with hook tip, body, a 1X/10X switch, a ground lead with a clip, a BNC connector and a small compensation adjuster. Set 1X/10X to match the scope channel. Compensate on the scope test terminal first. 1 2 3 4 5 6 7 8 Parts (numbers match the drawing) 1 Probe tip (hook, fine) 2 Probe body (insulated) 3 1X / 10X switch 4 Cable 5 BNC connector (to scope) 6 Ground lead 7 Ground clip: short as possible 8 Compensation adjuster (small screw)
A 10X scope probe with its ground lead. Source: author's drawing; Saleae Oscilloscope.
No. Part What it does Safety rule
1 Tip Touches the test point Keep the tip tidy; a lost cover can slip and short pins
2 Body Insulated holder Hold here
3 1X and 10X switch Chooses no attenuation or ten times attenuation The scope channel must be set to match
4 Cable Carries the signal Do not kink
5 BNC connector Plugs into the scope Twist to lock
6 Ground lead Joins the probe's ground to the circuit ground Keep it as short as possible; a long lead adds false ringing
7 Ground clip Clips to a ground point Never to a live point
8 Compensation adjuster A tiny screw that matches the probe to the scope input Use the scope's test terminal and a plastic tool

SAFETY PROTOCOL: oscilloscope and probes Before you start. Check the scope's earthed plug and the probe's insulation. Choose the probe setting (1X or 10X) and set the channel to match. Compensate the probe on the test terminal. Know the circuit: low-voltage or isolated only. While you work. Clip the ground first, to a ground point near the test point. Touch the tip to the test point with one hand. Mains-side measurements are for qualified technicians with isolation equipment. Never float or break the scope's earth to take a mains-side reading. After. Disconnect the tip first, then the ground. Switch off. Store the cover on the tip. Record the reading and the settings. Emergency. A spark or a shock: stop, switch off at the source if safe, keep others away and call your trainer. Call 112 for a serious shock, burn or fire. Do not touch a person who is still in contact with mains. Ask a qualified expert. A qualified technician or an Energy Commission-certified electrician must approve any mains-side measurement; for injury see a doctor or nurse. Meter and probe safety categories (CAT) are the maker's claim for the place of use.

Tools and items for this unit

Item What it is and what it does Size or type Also called Safety rule
Oscilloscope Draws a graph of voltage against time 2 channels scope, CRO Earthed plug; low-voltage or isolated only
Probe (10X) A lead that reduces the signal by ten and loads the circuit less Passive scope probe Compensate; short ground
Function (signal) generator Produces test sine, square and triangle signals Bench signal generator Low-voltage output only
Logic probe Shows high, low or pulsing on a digital line Pen Low-voltage only
Isolated probe Probe built to float safely from the ground Specialist differential probe Used by qualified persons
Service manual The maker's document with schematic and notes PDF or book repair manual Follow it

Writing a repair report

A good report has: customer and date, the item and model, the symptom in the customer's words, the tests you did, the fault found, the parts replaced, the result, the price, and the guarantee. A report lets another technician continue your work and protects you in disputes.

Trace a fault

  1. Take a Tier A board with a known fault (a faulty audio stage, for example) and its diagram.
  2. Draw the blocks and mark the half-split points.
  3. Measure the supply, then the middle of the chain. Decide where the signal stops.
  4. Test the parts in that stage out of circuit.
  5. Replace the faulty part and test.
  6. Write a one-page repair report.
  7. Under supervision, practise using a scope on a low-voltage signal: compensate the probe, connect the ground close, and draw the trace.

Draw a map

Take a simple battery device (not mains) and draw its circuit diagram from what you find inside. Mark where you would measure.

Check yourself

  1. What is half-split fault finding?
  2. Why use the manual for the exact model?
  3. Where must the scope's probe ground clip go?
03

Unit 2 · Advanced repair: SMD, hot air and parts

Modern boards use small surface-mount parts. Learn to place and remove them calmly, buy parts honestly and refuse risky substitutions.

Competency standard

Learning outcome Performance criteria — the trainee…
2.1 Solder SMD parts places and solders two-terminal and small multi-pin parts with iron and flux
2.2 Use hot air removes and refits a small part with correct temperature and airflow
2.3 Know the limits refuses BGA and reball work without proper equipment and training
2.4 Source parts buys from reliable sources, checks parts and keeps records
2.5 Substitute safely uses equal or better parts only where the specification allows

Range. Dead low-voltage practice boards; scrap boards. Evidence. Observation; repaired boards; parts log.

Ask a qualified expert. Hot air and solder fume need extraction; see a doctor or nurse if you wheeze or cough after work. Mains-powered boards remain Tier B with a qualified technician; ask an Energy Commission-certified electrician for building wiring.

SMD with the iron

  1. Put a little flux on the pads. Tin one pad.
  2. Hold the part with tweezers in place and touch the tinned pad to fix one end.
  3. Solder the other end. Re-flow the first end if it is crooked.
  4. For multi-pin parts, tack two opposite corners, add flux, and drag solder along the pins; remove bridges with braid.
  5. Clean with isopropyl alcohol and inspect with a magnifier.

Hot air

Beginner guides from tool makers suggest about 260 to 350 °C at low or medium airflow for most small SMD jobs, heating gradually. Figures vary between sources and with the part, so follow the datasheet and your station's manual.

  • Use a nozzle that fits the part. Keep it moving in small circles about 1 to 2 cm above the part (example guidance).
  • Too much airflow blows nearby parts away. Shield or tape neighbouring plastic parts.
  • Heat gradually; large boards absorb heat in copper planes.
  • Lift the part with tweezers only when all the solder is shiny and moves.
  • Clean and re-tin the pads, place the new part, and re-flow.

BGA (ball grid array) chips have balls under the chip, not pins. They need a reballing station and training and are not for beginners. Refuse such work unless you have the right equipment.

Hot-air rework station with every part numbered A hot-air station with a base unit holding a temperature display, temperature knob, airflow knob and power switch, a hose to a handpiece with a nozzle, and a holder stand. 320 C 1 2 3 4 5 6 7 8 Parts (numbers match the drawing) 1 Display (set temperature) 2 Temperature knob 3 Airflow knob 4 Power switch 5 Hose (do not kink) 6 Handpiece 7 Nozzle (choose the size) 8 Holder stand (always return here)
A hot-air rework station. Source: author's drawing; Gordak Hot Air.
No. Part What it does Safety rule
1 Display Shows the set temperature Check the setting before lifting the handpiece
2 Temperature knob Sets the air temperature Start low and raise slowly
3 Airflow knob Sets how strongly the air blows High airflow blows small parts away
4 Power switch Switches the unit Switch off only when the nozzle has cooled; some units need a cooling cycle
5 Hose Carries the air Do not kink or pull
6 Handpiece Holds the heater and the nozzle Never point at a person
7 Nozzle Directs the hot air at the part Choose the size that fits the part
8 Holder stand Where the handpiece rests Always return it here

SAFETY PROTOCOL: hot-air rework station Before you start. Place the station on a heat-proof surface away from paper. Wear glasses. Set the fan to blow fume away. Shield nearby plastic parts. Choose a nozzle to fit. Set temperature low and increase gradually; sources vary, so follow the datasheet and the station's manual. While you work. Keep the handpiece moving in small circles above the part, never touching it. Never point at your hand or face. Never leave a hot handpiece in your hand: use the stand. Do not heat a battery or a sealed part. After. Return the handpiece to the stand. Let the nozzle cool until the unit says it is safe. Clean flux with isopropyl alcohol. Switch off and unplug. Wash hands. Emergency. A burn: cool under running water for 10 minutes and cover it; see a doctor or nurse if large or blistered. A fire: switch off if safe, use the extinguisher you were trained on, call 112 if not under control at once. Ask a qualified expert. For burns and breathing problems see a doctor or nurse; for the right extinguisher ask the Ghana National Fire Service.

Parts and counterfeits

Fake parts are common. Typical signs: wrong or messy markings, wrong date codes, pins that look re-tinned, a capacitor in a case that is too large for its value. Many tiny ceramic capacitors carry no marking at all, so you cannot tell by eye.

  • Buy from shops that give a receipt and take returns. Keep the receipt with the job record.
  • Compare an unknown part with a known good one on the meter.
  • Salvaged parts may be worn or old: test before using.
  • In Ghana, the Ghana Standards Authority has stepped up its fight against sub-standard electrical products. Do not fit parts that you suspect are counterfeit into a customer's device.

Substitution rules

Part Substitution rule
Resistor Same value; equal or higher power rating
Electrolytic capacitor Same capacitance; equal or higher voltage; similar size
Diode, transistor, regulator Use the exact type or a cross-reference from the data sheet
Fuse Same current and voltage rating and type; never bigger
Safety-marked parts (in mains supplies) Exact replacement only; by a qualified technician
Unknown IC Do not guess; obtain the exact part
Anti-static (ESD) bench set-up with every part numbered A worker with a wrist strap on a bench covered by a static-dissipative mat; both connect by cords to one common point ground; a board lies on the mat. static-dissipative mat common point ground 1 2 3 4 5 6 7 Parts (numbers match the drawing) 1 Static-dissipative mat 2 Wrist strap (touches bare skin) 3 Coiled cord with resistor inside 4 Common point ground 5 Cord from the mat 6 Board being worked 7 Bench
An ESD-safe bench. Source: author's drawing; iFixit ESD.
No. Part What it does Safety rule
1 Static-dissipative mat Drains static slowly from the parts on it Keep clean and dry
2 Wrist strap Keeps you at the same potential as the bench Wear on bare skin; do not wear on a mains power supply or a CRT
3 Coiled cord with resistor Joins the strap to the ground point; has a built-in resistor Replace if cut; check the label
4 Common point ground One point where the mat and the strap are joined Connection to earth is done by a qualified electrician
5 Cord from the mat Links the mat to the common point
6 Board being worked The item under repair Keep it on the mat
7 Bench The work surface Keep it tidy

SAFETY PROTOCOL: ESD bench Before you start. Unplug the unit first. Check the strap cord and the mat. Put on the strap, bare skin. While you work. Touch the mat or the board frame before touching parts. Do not wear the strap while working on a mains power supply or a CRT. Keep plastic cups, bags and clothing away from sensitive parts. After. Put sensitive parts in anti-static bags. Remove the strap by the plug. Emergency. A shock through the strap means the ground is wrong: stop, unplug and call a qualified electrician; call 112 for a serious injury. Ask a qualified expert. The earth connection of the bench is for a qualified electrician; for injury see a doctor or nurse.

ESD at advanced level

Use a wrist strap with its built-in resistor on low-voltage boards, an anti-static mat and bags. Do not wear a strap on mains-powered supplies.

Parts decisions

Decide: use, refuse or test first, and why. (1) A 1,000 µF 25 V capacitor to replace a 1,000 µF 16 V part. (2) A 5 A fuse to replace a blown 2 A fuse. (3) A transistor from a salvaged board, unmarked. (4) A BGA chip removal for a customer's laptop.

SMD and hot-air drills

  1. On a practice board, solder five two-terminal SMD parts with the iron.
  2. Solder one small multi-pin SMD part by tacking and dragging; remove any bridge.
  3. With hot air, remove a small part, clean the pads, and refit it. Record the temperature and airflow.
  4. Test each result with the meter.
  5. List three parts you would test before using, and how.
  6. Write a parts log: source, date, receipt number and job.

Spot the fake

Look at three online listings of an electronic part (do not buy). List two warning signs that the part may be fake or unsuitable.

Check yourself

  1. Name one rule for fuse substitution.
  2. What is BGA, and why refuse it without training?
  3. Name two signs of a fake part.
04

Unit 3 · Power electronics faults

Switch-mode supplies and inverters are the heart of modern electronics, and a large share of the faults. You study them so you can diagnose them, advise honestly, and do the parts of the repair that are safe for you.

Competency standard

Learning outcome Performance criteria — the trainee…
3.1 Explain a switch-mode supply draws and names the stages, including feedback and protection
3.2 Do dead tests finds blown fuse, shorted switching part, failed capacitor, open start-up resistor under supervision
3.3 Judge repair or replace weighs repair cost, safety and re-failure risk
3.4 Handle inverter and battery faults diagnoses the battery side and the low-voltage stage and refers the mains side
3.5 Respect the gate refuses powered mains work; refers it

Range. Low-voltage stages and battery sides (Tier A); mains-power boards dead and supervised (Tier B). Evidence. Observation; dead-test table; case reports.

Ask a qualified expert. Switch-mode supplies and inverters contain dangerous mains voltage and charged capacitors. Powered tests are for a qualified electronics technician or an Energy Commission-certified electrician; solar charge controllers and installation need a licensed electrician (see the hub's Solar Energy modules). For shock or burns, see a doctor or nurse; in an emergency call 112.

Stages of a switch-mode supply

  1. Input: fuse, filter, rectifier and the large primary capacitor (dangerous stored charge).
  2. Start-up: a high-value resistor (or a small circuit) gives the control chip its first power.
  3. Switching: a fast switch (transistor or MOSFET) chops the DC into pulses through a small transformer.
  4. Secondary: the transformer's output is rectified and smoothed to low-voltage DC outputs.
  5. Feedback: a part (often an optocoupler) reports the output voltage back to the control chip, which adjusts the pulses.
  6. Protection: over-current, over-voltage and short circuit protection stop the supply to save the device.
Feedback loop of a flyback supply with every part numbered Schematic blocks: rectified DC to the primary winding with a switch under a controller and a sense resistor, the secondary to the output, and a feedback path from the output through a reference chip and an optocoupler back to the controller, crossing the isolation gap. Rectified DC Primary Secondary Output DC Switch Controller Sense R Optocoupler TL431 1 2 3 4 5 6 7 8 Parts (numbers match the drawing) 1 Primary winding (mains side) 2 Secondary winding (output side, isolated) 3 Switch (MOSFET) 4 Controller (PWM chip) 5 Current-sense resistor 6 Output (low-voltage DC) 7 Optocoupler (light across the gap) 8 Reference chip (TL431 type)
The feedback loop of a flyback supply. The dashed path crosses the isolation gap through the optocoupler. Source: author's drawing; Seaward IEC 62368.
No. Part What it does Safety rule
1 Primary winding Takes the chopped mains-side DC Mains side: dangerous
2 Secondary winding Gives the isolated low-voltage output Do not bridge to the primary
3 Switch Chops the current on and off Common failure part
4 Controller Adjusts the pulse width to keep the output steady Exact replacement only
5 Current-sense resistor Tells the controller how much current flows A burnt one shows overload
6 Output The low-voltage DC
7 Optocoupler Sends the feedback across the isolation gap by light Bridging it removes the isolation
8 Reference chip (TL431 type) Compares the output with a fixed reference Read the data sheet

Typical symptoms and dead-test clues

Symptom Clues to look for (dead tests, supervised)
Dead; fuse blown Shorted switching part, shorted rectifier, shorted primary capacitor
Dead; fuse good Open start-up resistor, open fuse, failed control chip
Output low or unstable Weak secondary capacitors (bulged), failing optocoupler
Clicking or squealing (hiccup) Dried secondary capacitors, a shorted load drawing too much; protection cycling
Hot parts or burnt smell Shorts; stop and refer

A blown fuse is a symptom, not the fault. Never fit a new fuse and switch on. Look for the cause first.

Isolation transformer and series lamp set-up for a qualified person, with every part numbered Mains supply feeding an isolation transformer, then a series lamp used as a current limiter, then the unit under test; a mat below. For qualified persons only. Mains Unit under test insulating mat, dry floor, one hand away from the unit 1 2 3 4 5 Parts (numbers match the drawing) 1 Mains supply with fuse or breaker 2 Isolation transformer (separates the unit from earth) 3 Series lamp (limits fault current) 4 Unit under test (opened) 5 Insulating mat and dry floor
An isolation transformer and series lamp set-up. For a qualified person only. Source: author's drawing; Seaward IEC 62368.
No. Part What it does Safety rule
1 Mains supply with a fuse or breaker Brings power in Fuse or breaker sized by the qualified person
2 Isolation transformer Separates the unit under test from the mains earth so a single touch is less likely to complete a path It does not make live parts safe to touch
3 Series lamp A bulb that limits the current if the unit has a short; glows bright on a fault Choose the bulb by the technician
4 Unit under test The opened item Only a qualified person works on it
5 Insulating mat and dry floor Stops a path to earth through the feet Keep dry

SAFETY PROTOCOL: first power-up behind an isolation transformer and series lamp (qualified person only) Before you start. A qualified technician checks the set-up, fuses, and the unit for repairs. Isolate and discharge the unit as in Level 2. Make sure the area is dry and others are away. While you work. One hand only. Switch on with the series lamp in the loop. A steady bright lamp means a short: switch off and find the fault. Never remove the lamp "to see if it works". Never touch live parts. After. Switch off and unplug. Discharge again and confirm dead before you open it again. Record the test. Emergency. A shock or a smell of burning: switch off at the source, keep others away and call 112; do not touch the person until the supply is off. Ask a qualified expert. This is live work. Only a qualified electronics technician or an Energy Commission-certified electrician may do it; trainees do not. For injury see a doctor or nurse.

Repair or replace?

Decide with honesty:

  • Is the cost of repair more than about half the cost of a new unit?
  • Are safety-marked parts involved (the guides call for exact replacements)?
  • Is there evidence of repeat failure (poor design, fake parts, surges)?
  • Can the work be tested safely before the customer takes it?

If any answer is no, advise replacement and explain why.

Inverters and UPS at advanced level

Most faults come from the battery side: age, charge, terminals and fuses. Next come the low-voltage control: cooling fans, relays and the switching transistors fed from the battery. The mains output stage is for qualified people.

  • A modified-sine inverter may make some equipment buzz or run poorly; a pure sine inverter suits sensitive loads.
  • Lithium batteries that are swollen must be removed from service and handed in for proper disposal.
  • Do not use solar charge controllers or PV wiring as practice: see the hub's Solar Energy modules and use a licensed electrician.

Case discipline

Write each case in a report: symptom, tests, causes ruled out, cause found, part replaced, test result, who powered it up, and the customer's advice.

Case decisions

Decide: repair, replace or refer, and why. (1) A sealed phone charger with a cracked case. (2) A UPS giving 5 minutes of back-up with a four-year-old battery. (3) An amplifier power supply with a blown fuse and a shorted rectifier diode. (4) A swollen lithium battery pack.

Dead-test table

  1. Under supervision, take a scrap switch-mode supply board, isolate and discharge, and confirm dead.
  2. Draw its stages from the board; mark fuse, rectifier, primary capacitor, switching part, transformer, optocoupler.
  3. Test each part dead and write the results in a table.
  4. Mark the parts you would replace and say why.
  5. Write a short report with your repair or replace advice.

Honest advice

Write what you would tell a customer whose power supply has failed twice in six months, in plain words, including the cost and the risk.

Check yourself

  1. What does the optocoupler do?
  2. Why is a blown fuse only a symptom?
  3. Who powers up a repaired mains supply?
05

Unit 4 · Quality, standards, e-waste and supervising

Quality is a promise you keep every time. At this level you also teach others, so your habits become theirs.

Competency standard

Learning outcome Performance criteria — the trainee…
4.1 Run a quality check uses a final checklist before returning any item
4.2 Know the rules that touch the trade says what the Energy Commission, GSA and EPA do
4.3 Handle e-waste legally sorts, stores and hands over e-waste properly
4.4 Supervise an apprentice plans tasks by tier, checks work and records progress
4.5 Handle complaints and returns records and learns from returns

Range. Workshop and business practice. Evidence. Checklists; apprentice record; observation.

Ask a qualified expert. Laws and fees change; this unit is general information, not legal advice. For appliance rules ask the Energy Commission or the Ghana Standards Authority; for e-waste ask the EPA; for apprentices and employment ask the Labour Department or a qualified lawyer. For electrical work ask an Energy Commission-certified electrician. For injury, see a doctor or nurse.

Tools and items for this unit

Item What it is and what it does Also called Safety rule
Tools register List of every tool, its condition and its calibration date tool log Update weekly
Calibration sticker Shows when an instrument was last checked cal label Do not use out-of-date instruments for safety tests
Labelled bins Boxes for parts, e-waste, batteries Never mix batteries with general waste
Parts traceability label A label showing which job a part came from
Torque screwdriver A screwdriver that stops at a set tightness Do not over-tighten plastic
Fixture or jig A holder that places a board the same way each time

The final quality checklist

Before you return an item, check and tick:

  • The fault the customer reported is fixed and the item works as it should.
  • No new fault was caused (check lights, buttons, sockets).
  • Solder joints are neat; flux cleaned; no loose wires or screws.
  • Case closed with all screws; no sharp edges or cracked plastic.
  • For battery items: battery fresh or tested; no swelling.
  • For mains items: a qualified person has done the safety checks and first power-up; the item is not returned if it fails them.
  • Job record complete; price agreed; guarantee note given.
  • Parts removed are returned or sorted for e-waste.

The rules around the trade

  • Wiring: only Certified Electrical Wiring Professionals under L.I. 2008 may do indoor wiring. A repair shop does not do wiring.
  • Appliance standards: the Energy Commission's standards and labelling regime covers appliances such as lamps, air-conditioners and refrigerators, and a notice said stricter import enforcement was to apply from December 2025; the current position is not verified. Ask the Commission.
  • Sub-standard goods: the GSA has said it is stepping up market enforcement under the Ghana Standards Authority Act, 2022 (Act 1078). Do not sell or recommend goods you know are sub-standard.
  • E-waste: the Environmental Protection Act 2025 (Act 1124) replaced Act 917 and regulates hazardous and electronic waste; producers and importers register with the EPA and pay a levy. A fund for e-waste is set up under the Act. For a repairer: ask the EPA what is needed to handle or hand over e-waste.
  • Health: the WHO says open burning of e-waste is the most hazardous practice. Greenpeace Africa reports that informal e-waste workers lack protection and urges support for repair and refurbishing. Your trade is part of the solution: repair, sort, never burn.

Supervising an apprentice

  1. Register the apprentice. STMA says master artisans must register their trainees.
  2. Write the tiers of tasks the apprentice may do: only Tier A alone at first; Tier B never without a qualified supervisor; Tier C never.
  3. Demonstrate, watch, check, hand over: show the task, watch them do it, check the result, then let them do it alone.
  4. Record what the apprentice has learned, task by task, with dates. This helps for a later test or certificate.
  5. Treat them fairly. Under the Labour Act a written contract is needed for employment of 6 months or more, and workers get 15 working days' paid leave. An apprentice may be covered by a separate apprenticeship agreement; ask the Labour Department or a lawyer.
  6. Pay. Do not underpay; the minimum wage for 2026 is GH¢21.77 a day for workers. Whether apprentice allowances count is not verified.

Your name is on the work. If an apprentice makes a mistake, you answer to the customer. Check every job before it leaves.

Complaints and returns

  • Welcome returns. Write the date, the fault, the cause and what you did.
  • Work out your return rate = returns ÷ jobs. A rate that rises tells you something is wrong: bad parts, rushing or an untrained apprentice.
  • Replace or repair free within the guarantee and say what is not covered.

Return rate

Ama's table did 60 jobs in March and 3 came back. Each return cost her GH¢20 of time and parts (example). (1) What is her return rate? (2) What did returns cost in March?

Quality and apprentice plan

  1. Write a final checklist for your table.
  2. Check three finished repairs with it. Record any failures.
  3. Make a one-page apprentice plan: name, tasks by tier, who checks, dates.
  4. Make an e-waste box and write a rule for handing it over.
  5. Write a returns sheet with columns for date, item, fault, cause and cost.

Ask the EPA

Find out (by visiting the EPA Western Region office or a trusted contact) how a small repair shop should hand over e-waste. Write what you learn, or write that it could not be verified.

Check yourself

  1. What is the return rate formula?
  2. Which tier may a new apprentice work in alone?
  3. Why never burn cables or boards?
06

Unit 5 · Establish your own business

A good technician is not yet a business owner. A business needs a legal form, a place, money, a plan and people who trust you.

Competency standard

Learning outcome Performance criteria — the trainee…
5.1 Choose a legal form compares sole proprietor, partnership, company and cooperative
5.2 Register step by step lists the bodies and fees for a business name, TIN, permit and trade licences that apply
5.3 Plan premises and start-up works out a start-up budget and chooses a good location
5.4 Find finance names three sources and their risks
5.5 Write a plan and pitch writes a one-page plan and gives a pitch
5.6 Hire, insure and market explains hiring basics, insurance and marketing channels

Range. A small electronics repair business in the Takoradi area. Evidence. Registration checklist; start-up budget; one-page plan; pitch.

Ask a qualified expert. Fees, taxes, permits and the law change. This unit is general information, not legal, tax or financial advice. Ask the Office of the Registrar of Companies, GRA, the Sekondi-Takoradi Metropolitan Assembly (STMA), a qualified accountant or lawyer, and a bank or the Ghana Enterprises Agency before you act. Electrical work stays with an Energy Commission-certified electrician.

Choose a legal form

Form What it is 2026 ORC fee Remarks
Sole proprietor (business name) You and the business are one; unlimited liability GH¢130; renewal GH¢70 a year Simplest start
Partnership 2 to 20 partners; partnership agreement GH¢270; renewal GH¢100 a year Agreement stamped at the Lands Commission
Company limited by shares A separate legal person GH¢585 plus a 1% capital duty on stated capital; the rate as printed needs checking At least 2 directors and a secretary; annual returns
Cooperative Members own it Not registered at ORC; organisational TIN from GRA Department of Co-operatives route not verified

Annual returns cost GH¢175 a year, and late filing is GH¢1,000 (1 to 4 years) or GH¢2,000 (5 years or more). For a new repair table, a business name is usually enough; a company is worth considering when you have partners, staff and larger contracts.

Registration step by step

  1. Search and register the business name at the ORC.
  2. Tax identity. An individual's Ghana Card PIN has been the TIN since 1 April 2021; companies get a TIN from GRA after ORC registration.
  3. Assembly business operating permit. STMA has an online portal and a fee-fixing list; the fee for an electronics repair table is not verified. Ask the STMA revenue office. Permit payment is due by 31 March in the filing calendar in the shared facts.
  4. Trade licences. No Energy Commission licence is needed for a repair table that does no wiring (not verified); wiring needs a certified electrician. Ask the Energy Commission if unsure. For a shop, a Ghana National Fire Service certificate may apply: not verified.
  5. Register your trainees.
  6. Tax route. A resident with only business income who is not VAT-registered may use the Modified Taxation Scheme: turnover up to GH¢20,000 pays fixed instalments; GH¢20,001 to GH¢750,000 pays 3% of turnover (the ceiling was raised from GH¢500,000 by the Income Tax (Amendment) Act 2026; GRA's own page still showed 500,000 on 8 October 2026).
  7. VAT. From 1 January 2026, VAT is 15% plus NHIL 2.5% and GETFund 2.5%; the registration threshold for goods is GH¢750,000; services have no turnover threshold, so a repair business that supplies taxable services should ask GRA or an accountant whether it must register within 30 days. A VAT-registered business cannot use the Modified Taxation Scheme.
  8. Withholding tax. Payers may withhold tax on payments to you, for example 7.5% on services above GH¢2,000 a year for some payers; ask for the certificate.
  9. Keep records for at least six years.

Tools and items for this unit

Item What it is Safety rule
Fire extinguisher Cylinder for small fires; the right type is a Ghana National Fire Service question Know where it is; service it
Signboard Tells the customer what you do and where Check the council rules
Lockable cabinet Keeps customers' items safe Keep a register
Receipt printer or book Gives proof of payment Keep copies
Mobile-money record Your account of customer payments Reconcile weekly

Premises and location

  • Choose places with foot traffic (market, lorry station, school, shop corner) and a safe, dry, lockable space with power and light.
  • Rent and power are fixed costs. Compare at least three places.
  • Keep the bench away from rain, dust and children, and keep a clear fire route.

Start-up budget (example)

Item Example GH¢
Soldering station 1,000
Multimeter 250
Bench power supply 500
Hand tools 350
Magnifier lamp 150
Fume extractor or fan 150
Bench equipment 2,400
Starting parts stock 900
Table, shelves and lockable box 400
Signboard 150
Business name registration 130
Start-up total 3,980
Working capital (money for the first two months) 2,020
Total capital needed 6,000

All figures are examples; the 2026 name fee is from the ORC. Jiji asking prices in a November 2026 search ranged from about GH¢61 for a basic iron to about GH¢1,000 for a station, and from GH¢160 to GH¢250 for common multimeters.

Finance

Source Remarks
Own savings and family Cheapest; agree terms in writing
Susu or VSLA Small amounts; regular saving habit
Microfinance or bank loan Interest and collateral; use a licensed lender; the policy rate was 14.00% at the Bank of Ghana
Ghana Enterprises Agency (GEA) programmes Business advisory centres in Takoradi and nearby; programmes change
Government budget programmes The 2026 Budget names the National Apprenticeship Programme and others; check eligibility
Assemblies' disability fund Share not verified; ask your Assembly

Take a loan only for equipment that earns money, and only an amount you can repay from profit. Compare lenders and read the contract; ask a qualified accountant or financial adviser.

Hire, insure and market

  • Hire. Register workers with SSNIT: the employee pays 5.5% and the employer 13% of basic pay, a total of 18.5%. The employer pays within 14 days after month-end. Employers deduct PAYE and pay by the 15th of the next month.
  • Insure. Use only an insurer licensed by the National Insurance Commission; verify at its website. Compulsory covers for a workshop are not verified.
  • Market. WhatsApp Business, Google Business Profile, a clear signboard, a portfolio with before-and-after photos (with permission), referrals and honest advice.

One-page business plan and pitch

A one-page plan has: who you serve, what you offer (Tier A and B services, no Tier C), where, prices, start-up cost and capital, monthly costs, break-even number of jobs, how you will market, risks and what you ask for. Practise a two-minute pitch that covers the same points.

Accessibility

Persons with disabilities can run a repair business (author's judgement; the Persons with Disability Act 2006 protects their rights, but check the text). A seated bench, good lighting, a magnifier, simple signs, and WhatsApp for ordering suit many owners. Deaf owners can work well because the work is visual. Choose a ground-floor location. Ask the Assembly about its disability fund; the share was not verified.

Pick the form

Kojo wants to start a repair table alone with GH¢6,000. Esi and Yaw want to start together and put GH¢3,000 each. (1) Which form suits Kojo and what is the 2026 ORC fee? (2) Which suits Esi and Yaw and what is the ORC fee? (3) What must be added for Esi and Yaw's agreement?

Registration pack

  1. List each registration step for your business, who to ask, and the fee or "not verified".
  2. Make your start-up budget and capital need.
  3. List three sources of finance and the risk of each.
  4. Write a one-page business plan.
  5. Give a two-minute pitch to a classmate.

Visit the STMA

Visit or call the STMA revenue office (or ask a local master artisan) and find the operating permit rules for an electronics repair table. Write what you learn, or "not verified".

Check yourself

  1. What is the 2026 ORC fee for a business name?
  2. Which tax route is for small sole proprietors who are not VAT-registered?
  3. Who may you register with SSNIT?
07

Unit 6 · Accounting and bookkeeping for a repair shop

If you do not write it down, you do not own it. Keep a few honest books and you will know whether you are making money before the money runs out. This unit goes deeper than the hub's Money Skills Level 2 and the Entrepreneurial Thinking Level 2.

Competency standard

Learning outcome Performance criteria — the trainee…
6.1 Keep the books keeps a cash book, receipts, petty cash and stock records
6.2 Track debtors and creditors records who owes you and whom you owe
6.3 Make statements prepares a simple income statement and balance sheet
6.4 Cost, price and break even prices jobs, compares margin and mark-up, and finds break-even
6.5 Depreciate and reconcile depreciates equipment; reconciles cash and MoMo monthly
6.6 Run the month-end and tax records closes the month; keeps tax records

Range. One small repair business. Evidence. Books for a month; statements; calculations in the logbook.

Ask a qualified expert. Tax and accounting rules change. This unit is general information, not tax or accounting advice. Check with GRA or a qualified accountant before you file or pay tax, and for the SSNIT and PAYE of your workers. Free tools such as a spreadsheet are enough to begin.

The basic idea

Assets = Liabilities + Equity. Assets are what the business owns (cash, stock, equipment, money owed to it). Liabilities are what it owes. Equity is the owner's share. Debits increase assets and expenses; credits increase liabilities, capital and income. A trial balance checks that the books balance, but it is only a partial check.

Tools and items for this unit

Item What it is Safety rule
Job-tracking software or notebook Lists every job, status and price Back it up
Sales book Lists each sale Match to receipts
Ledger Double-entry accounts See the worked example

The records you keep

Record What goes in it
Cash book Every cash and MoMo receipt and payment, in date order
Receipts and invoices A copy of each; numbered
Petty cash Small cash for tea, transport, tape; with a float and a voucher for each payment
Stock card Each type of part: bought, used, left
Job book Each job with fault, fix, price and guarantee
Debtors list Customers who owe you, amount and date
Creditors list Suppliers you owe, amount and date

Keep records in Ghana for at least six years. Keep owner's money and business money apart: use a separate MoMo wallet or account and pay yourself a fixed amount, called drawings.

A worked example: Kofi's repair shop in March (all figures are examples)

Opening position. Kofi puts GH¢6,000 of capital into the business on 1 March. To keep the example short, assume the table, signboard and name were already paid in the start-up budget (Unit 5), and the bench equipment of GH¢2,400 is bought on 2 March.

March cash book summary.

Item In GH¢ Out GH¢
Capital from owner 6,000
Bench equipment 2,400
Parts bought for cash 1,100
Cash sales received 3,900
Rent 300
Power 80
Data 60
Transport 150
Advertising 40
Apprentice allowance 400
Drawings (Kofi's pay) 800
Totals 9,900 5,330
Closing cash 4,570

(9,900 − 5,330 = 4,570.)

Other facts at 31 March. Total sales for the month were GH¢4,200, of which GH¢300 is owed by a shop customer (a debtor). Parts bought in the month totalled GH¢1,400 (GH¢1,100 paid and GH¢300 owed to a supplier, a creditor). A count shows GH¢250 of parts left (closing stock). The bench equipment is depreciated over 4 years with no value left at the end.

Depreciation. (cost − salvage) ÷ useful life. (2,400 − 0) ÷ 4 = GH¢600 a year = GH¢50 a month.

Cost of parts used. Opening stock 0 + parts bought 1,400 − closing stock 250 = GH¢1,150.

Income statement for March (profit and loss).

Line GH¢
Sales 4,200
Less cost of parts used 1,150
Gross profit 3,050
Rent 300
Power 80
Data 60
Transport 150
Advertising 40
Apprentice allowance 400
Depreciation 50
Total expenses 1,080
Net profit 1,970

(3,050 − 1,080 = 1,970.)

Balance sheet at 31 March.

Assets GH¢ Liabilities and equity GH¢
Cash 4,570 Creditors (supplier) 300
Debtors 300 Capital 6,000
Stock of parts 250 Add net profit 1,970
Equipment (2,400 − 50) 2,350 Less drawings (800)
Owner's equity 7,170
Total assets 7,470 Total liabilities and equity 7,470

The two sides agree: 4,570 + 300 + 250 + 2,350 = 7,470 and 300 + 7,170 = 7,470. Note: profit (GH¢1,970) is not the same as cash (GH¢4,570): cash includes the capital, and profit includes money not yet received and stock not yet used.

Costing, margin and mark-up

  • Mark-up is a percentage of cost. Margin is a percentage of price.
  • Example: cost GH¢82.50, mark-up 30% gives a price of 82.50 × 1.30 = GH¢107.25. Margin = (107.25 − 82.50) ÷ 107.25 = 24.75 ÷ 107.25 = 23.1%.
  • A 30% mark-up is therefore only a 23.1% margin. Do not mix them.

Break-even

Kofi's fixed costs for March: rent 300 + power 80 + data 60 + transport 150 + advertising 40 + apprentice 400 + depreciation 50 = GH¢1,080. His gross margin is 3,050 ÷ 4,200 = 72.6%.

Break-even sales = fixed costs ÷ gross margin ratio = 1,080 ÷ 0.7262 ≈ GH¢1,487 a month. Below that he loses money; above it he profits.

Depreciation of a new hot-air station (example)

A hot-air station costs GH¢800, is expected to last 5 years and be worth GH¢100 at the end. (800 − 100) ÷ 5 = GH¢140 a year = GH¢11.67 a month.

Employee costs (example)

Ama is a paid helper on GH¢1,200 basic monthly pay (example). SSNIT: the employee pays 5.5% = GH¢66, the employer 13% = GH¢156, total 18.5% = GH¢222. PAYE on the pay after SSNIT (1,200 − 66 = 1,134): the 2026 monthly bands are the first GH¢588 at 0%, the next GH¢80 at 5%, the next GH¢100 at 10%, and the next GH¢2,900 at 17.5%. So tax = 0 + 4 + 10 + (1,134 − 768 = 366) × 0.175 = 4 + 10 + 64.05 = GH¢78.05. Ama's take-home pay is 1,200 − 66 − 78.05 = GH¢1,055.95. The employer's total cost is 1,200 + 156 = GH¢1,356. Check the current rates with GRA and SSNIT, and with a qualified accountant.

Tax records (check with GRA or an accountant)

  • A sole proprietor with only business income who is not VAT-registered may use the Modified Taxation Scheme: 3% of turnover in the GH¢20,001 to GH¢750,000 band. On Kofi's March sales annualised (4,200 × 12 = GH¢50,400), 3% would be GH¢1,512 a year (example only).
  • Services have no VAT turnover threshold; ask GRA whether you must register. A VAT-registered business cannot use the Modified Taxation Scheme.
  • Keep every receipt, invoice and bank or MoMo statement for six years.
  • Free software such as Wave and Zoho Books offers free plans with limits. A spreadsheet is enough for a table.

The month-end routine

  1. Total the cash book and check it against the cash in the box and the MoMo balance. Reconcile any difference (for example, a transaction fee not yet recorded).
  2. Count the stock and update the stock cards.
  3. Update the debtors and creditors lists.
  4. Record depreciation.
  5. Prepare the income statement and balance sheet.
  6. Pay yourself the fixed drawings; do not take extra.
  7. File and pay what is due (see the calendar in your plan; confirm dates with GRA and SSNIT).
  8. Write a one-line note: what went well, what to change.

March for Ama's table (all examples)

Ama starts with GH¢5,000 capital. In April she buys equipment GH¢1,800 (life 3 years, no salvage), parts GH¢900 for cash, and pays rent GH¢250, power GH¢70 and transport GH¢100. Sales are GH¢3,000, all in cash. Closing stock of parts is GH¢200. She takes drawings of GH¢500. (1) Cash at month end. (2) Cost of parts used. (3) Depreciation for the month. (4) Net profit. (5) Check that the balance sheet balances.

Break-even

Ama's fixed costs are rent 250, power 70, transport 100 and depreciation 50. Her gross margin is 2,300 ÷ 3,000. What is her break-even monthly sales?

Your own books for a month

  1. Set up a cash book, a stock card for five parts, a debtors list and a creditors list.
  2. Record a month of your practice jobs (real or role-played).
  3. Prepare an income statement and balance sheet.
  4. Work out break-even sales.
  5. Do the month-end routine and write your note.
  6. Ask your trainer to check that the balance sheet balances.

Margin or mark-up

Take three of your prices. For each, work out the mark-up on cost and the margin on price. Explain the difference in one sentence.

Check yourself

  1. What is the accounting equation?
  2. What is the difference between mark-up and margin?
  3. Why separate owner's money from business money?
08

Unit 7 · Grow, sustain and the capstone

A repair business grows by trust. Quality, honest prices, clear records and fair treatment of people carry you from one table to a trusted shop.

Competency standard

Learning outcome Performance criteria — the trainee…
7.1 Run quality systems uses checklists, a returns record and a customer-care routine
7.2 Set a pricing strategy sets a price list and tests it against break-even
7.3 Plan growth compares options to grow and their risk
7.4 Use records for loans and contracts prepares records a lender or client will accept
7.5 Plan ethics and succession writes a code of conduct and a simple succession note
7.6 Present the capstone presents a one-page plan and 12-month cash-flow forecast to a panel

Range. One small repair business. Evidence. Price list; forecast; capstone presentation.

Ask a qualified expert. Growth plans involve money, tax, contracts and employment. This unit is general information, not financial, tax or legal advice. Ask a qualified accountant, a lawyer, GRA, the GEA or your bank before you act. Electrical work stays with an Energy Commission-certified electrician.

Customer care

  • Greet, listen, write down the fault in the customer's words.
  • Give an honest estimate and tell the customer what you cannot do (Tier C).
  • Keep the customer informed. A short WhatsApp message saves a visit.
  • Return the item clean and tested, and show it works.
  • Ask for feedback and a referral.

Pricing strategy

Think of three levels: a basic check or fix (cheap, quick), a standard repair with a guarantee, and a premium repair with a longer guarantee or a collection service. Test every price against your break-even and your margin. Do not copy the cheapest shop; compete on trust and speed, and never cut prices below your cost.

Example price list (examples). Cable fix GH¢35; radio crackle fix GH¢50; amplifier dead-test and repair from GH¢107; battery or UPS battery-side check GH¢40; written estimate for a TV GH¢30 (credited if repaired).

Ways to grow

Option What it needs Risk
More hours or a second bench A trained apprentice Quality slips
A second location Rent and stock Cash tied up
Selling parts and chargers (tested, reputable) Stock money Fake or unsold stock
Contracts with schools, churches, shops, farms A written agreement and records Late payment
Training apprentices A plan and time Your time
Partnering with a phone repairer, computer shop or electrician Clear roles; refer, do not copy Disputes

Partner with an Energy Commission-certified electrician for wiring jobs and refer to them, rather than doing wiring yourself. Public tenders and bigger contracts usually need a tax identity, registration and clean records; ask the buyer's procurement office for the rules.

Records for loans and contracts

A lender or client wants: your registration, TIN, a few months of cash book, income statement, balance sheet, a cash-flow forecast, and proof of address. Your clean books are your best collateral. Keep records for six years. Government programmes announced in the 2026 Budget, such as the National Apprenticeship Programme, may be open to you; check eligibility with the agency.

Ethics and succession

  • Do not fit fake parts, charge for work not done, or hide faults.
  • Do not repair what is unsafe; refer it.
  • Do not burn e-waste, and do not leave it in the street.
  • Treat apprentices and customers fairly.
  • Succession: write a one-page note naming who can run the table if you are sick: where the keys, books and passwords are, who holds the customers' items, and who pays suppliers. Tell a trusted person.

The 12-month cash-flow forecast

A cash-flow forecast estimates money in and out each month so you know when cash may run short.

Worked example (all figures examples). Opening cash GH¢1,000. Sales start at GH¢2,500 in month 1 and rise by GH¢250 a month, so month 12 is GH¢5,250 and the year totals GH¢46,500. Parts cost 27% of sales. Fixed cash costs are GH¢1,030 a month (rent 300, power 80, data 60, transport 150, advertising 40, apprentice 400). Drawings are GH¢800 a month. Depreciation is not a cash cost, so it is left out.

Month Sales Parts (27%) Fixed costs Drawings Net cash change Closing cash
1 2,500 675 1,030 800 −5 995
2 2,750 742.50 1,030 800 177.50 1,172.50
3 3,000 810 1,030 800 360 1,532.50

(Month 1: 2,500 − 675 − 1,030 − 800 = −5; closing 1,000 − 5 = 995.) Continue the table to month 12 in your own sheet.

Forecast months 4 to 6

Using the same assumptions, work out the net cash change and the closing cash for months 4, 5 and 6, with sales of GH¢3,250, GH¢3,500 and GH¢3,750.

The capstone

You present to a panel (a repair shop owner, an accountant or GEA adviser, and a trainer):

  1. One-page business plan (Unit 5).
  2. 12-month cash-flow forecast with your own assumptions, saying which are examples and which you checked locally.
  3. Start-up budget and registration checklist with "not verified" items marked.
  4. Quality checklist, apprentice plan and e-waste plan.
  5. A live demonstration: a short diagnosis of a low-voltage fault with the tier rule stated.
  6. A five-minute pitch and answers to panel questions.

The panel uses the capstone checklist in the assessment table. The trainee is judged Competent or Not Yet Competent.

Prepare the capstone

  1. Finish your plan and your 12-month forecast.
  2. Check every figure and label examples.
  3. Prepare the quality checklist, apprentice plan and e-waste plan.
  4. Practise the pitch twice with a partner.
  5. Rehearse the live diagnosis.
  6. Hand in a folder of your books for a month.

Three questions

Write three hard questions a panel might ask you, and your honest answers.

Check yourself

  1. What is a cash-flow forecast for?
  2. Why is depreciation left out of a cash forecast?
  3. Name one rule of ethics for your table.
09

Glossary

Term Meaning
BGA Ball grid array; a chip with balls under it
Balance sheet A list of assets, liabilities and equity at one date
Break-even Sales or jobs needed to cover fixed costs
Cash-flow forecast A plan of money in and out by month
Creditor Someone you owe
Debtor Someone who owes you
Depreciation Spreading the cost of equipment over its life
Drawings Money the owner takes out of the business
Half-split Test the middle of the chain to halve the search
Margin Profit as a percentage of price
Mark-up Profit as a percentage of cost
Optocoupler A part that passes a signal by light across an isolation gap
Reconcile Match your records to the bank or MoMo statement
Return rate Returns divided by jobs
Calibration Checking an instrument against a known reference
Common point ground One point where bench ground paths join
Isolation transformer A transformer that separates a unit from the mains earth
Series lamp A bulb in series that limits fault current
Time constant R times C
True RMS A reading that follows the heating value of any waveform
10

Logbook

Copy these pages into an exercise book. Your logbook is part of your assessment evidence.

  • Unit 1: marked diagrams; repair report
  • Unit 2: SMD and hot-air record; parts log
  • Unit 3: dead-test table; case reports
  • Unit 4: final checklist; apprentice plan; returns sheet
  • Unit 5: registration pack; start-up budget; one-page plan
  • Unit 6: one month of books; income statement; balance sheet; break-even
  • Unit 7: price list; 12-month forecast; capstone folder
  • Every homework, dated
11

Self-check quiz

  1. What is half-split fault finding?
  2. Where does the scope's probe ground clip go?
  3. Give one rule for substituting an electrolytic capacitor.
  4. Why refuse BGA work without training?
  5. Why is a blown fuse only a symptom?
  6. Who does the first power-up of a repaired mains supply?
  7. What is the formula for return rate?
  8. What is the 2026 ORC fee for a business name?
  9. State the accounting equation.
  10. Cost GH¢82.50 with a 30% mark-up: price and margin?
  11. Kofi's fixed costs are GH¢1,080 and his gross margin ratio is 72.6%. What are the break-even sales?
  12. What is depreciation for an item costing GH¢2,400 with no salvage and a 4-year life, per month?
12

Appendix A · The Master Technician's Reference

Look-up pages for the advanced bench. Foreign values are labelled international: check them against the Ghana Standards Authority or Energy Commission text when read. Copy pinouts and ratings from data sheets; this book does not give them from memory.

Ask a qualified expert. Mains, high voltage, stored charge, hot air, solder fume and fire risks appear below. Mains work is for qualified technicians and Energy Commission-certified electricians; for injury see a doctor or nurse; for fire ask the Ghana National Fire Service.

A1 · Schematic reading kit

  • Symbols. Use the Level 1 symbol figure; add: fuse, switch, relay, transformer, optocoupler, MOSFET, regulator, ground types and connectors from the service manual's own legend.
  • Motifs to find. (a) Voltage divider: two resistors from a line to ground with the output between them; Vout = Vin x R2 / (R1 + R2). Worked example (checked by script): 12 V with 10 k over 4.7 k gives 3.84 V. (b) RC filter: a resistor in series with a capacitor to ground; cut-off frequency about 1 / (2 pi R C), so 10 k with 100 nF cuts at about 159 Hz. (c) Regulator: input capacitor, regulator chip, output capacitor. (d) Feedback: output sample, reference, optocoupler, controller (see the flyback figure in Unit 3).
  • Test-point log. Write each test point, the expected value from the manual, the measured value and the difference.
Test point Expected (manual) Measured Difference Meaning

A2 · Switch-mode reference

Stage What fails Signature Next test
Input (fuse, filter, bridge) Fuse, bridge, thermistor Dead, fuse blown Diode range on the bridge
Bulk capacitor Dried or shorted Dead or hum Capacitance, ESR vs a known-good part
Start-up Open start-up resistor Dead, fuse good Resistance
Switch Shorted Fuse blown, switch part short Dead test; then check the gate resistors
Controller Dead chip No pulses Scope on the gate at a safe point
Secondary Shorted rectifier or capacitor Output low, hot Diode range
Feedback Weak optocoupler, wrong reference Output high or hunting Dead tests then qualified powered test
Protection Latches off Clicking, hiccup Find the cause, not the latch

Safe test. Powered tests only by a qualified person behind an isolation transformer and a series lamp (Unit 3). Chip families found in Ghana chargers and TV supplies are not verified: read the chip's own marking and its data sheet.

Worked formulas (checked by script). Ideal buck output duty = Vout / Vin = 5 / 12 = 41.7%. Efficiency = out / in: 60 W out from 75 W in is 80% with 15 W lost as heat. Ripple on a smoothing capacitor is about I / (f x C): 1 A, 100 Hz and 2,200 microfarads give about 4.5 V (a rough guide only). Capacitor energy is half x C x V squared: 220 microfarads at 400 V holds 17.6 J.

A3 · Scope and logic-probe reference

  • 10X rule. A 10X probe divides the signal by 10: multiply the reading by 10 if the scope does not do it, and set the channel to match.
  • Compensation. Touch the probe to the scope's test terminal and adjust until the square wave has square corners.
  • Ground clip. Short, near the test point; the scope ground is earth.
  • Typical waveforms to expect: a square wave on a switching gate; a sawtooth or ripple on a smoothing capacitor; a clean DC on a regulator output with a little ripple. Match them to the service manual; the book gives no brand-specific values.
  • Measurement checklist: probe set and compensated; ground clip placed; range set; trigger set; unit is low-voltage or isolated; reading and setting written down.
  • Logic probe: shows high, low and pulses on digital lines; low-voltage only.

A4 · SMD and hot-air reference

Topic Reference
Chip sizes 1206, 0805, 0603 and 0402 typical sizes: see the figure in Level 2 Unit 3; check the data sheet
EIA-96 Two digits and a letter; the lookup table is in the maker's document
Hot-air start About 260 to 350 C at low or medium airflow, heated gradually; figures vary by source and part
Nozzle The size that fits the part; keep moving 1 to 2 cm above (example guidance)
Pre-heat A pre-heater or slow heat avoids thermal shock to large boards
Solder paste Applied with a stencil or a fine tip; the paste maker's profile is the guide
Flux Use no-clean or rosin flux; clean with isopropyl alcohol
IPC rework IPC-7711 and IPC-7721 describe rework, modification and repair; edition letters to be checked on ipc.org
BGA Refuse unless equipped and trained

Rework record form

Date Board and part Method (iron or hot air) Temperature and time Result Name

A5 · Parts and counterfeits

  • Read a data sheet. Find three things: absolute maximum ratings (never exceed), typical values, and the pinout and package drawing.
  • Cross-reference. Match the parameters that matter: for a transistor or MOSFET: type, voltage, current, package; for a diode: voltage, current, speed; for a regulator: output voltage and current; for an optocoupler: transfer ratio and isolation voltage.
  • Counterfeit signs. Wrong or messy markings; odd date codes; re-tinned pins; a part in a case too large for its value; unmarked tiny capacitors cannot be told by eye.
  • Incoming-parts log.
Date Part Shop Receipt number Inspection result Used in job
  • Supplier register (fill in from your own survey). Shop, address area, parts range, receipts given (yes or no), return policy, prices and date.

A6 · Quality system

  • Final quality checklist. Use the Unit 4 checklist as a form on every job card.
  • IPC class vocabulary. IPC-A-610 describes three classes by end use: Class 1 general electronics, Class 2 dedicated service electronics, Class 3 high-reliability equipment. Class is chosen by the end use, not by how the work was done. Standards are copyrighted: this book summarises and never reproduces them.
  • Calibration and tools register. Record each instrument, its calibration date and who checked it.
  • Complaint and return log.
Date Customer (private) Item Complaint Cause Action Cost to the shop
  • Returns analysis. Return rate = returns / jobs x 100. Review each month: group by cause.

A7 · Compliance crosswalk (with "checked on" dates)

Rule Owner Applies to What it means at my bench Source status Checked on
L.I. 2008 Energy Commission Indoor wiring Only Certified Electrical Wiring Professionals Official page
GS IEC 60884-2-1 and 2-2 Ghana Standards Authority Plugs and sockets Use approved plugs Summary only
Act 1078 (2022) Ghana Standards Authority Standards Penalties for sub-standard goods Summary only
Act 1124 (2025) EPA E-waste and hazardous waste Permit and eco-levy rules; the rate is not found Summary only
IPC J-STD-001, IPC-A-610, IPC-7711 and 7721 IPC (international) Soldering, acceptance, rework Quality language Foreign, summary only
IEC 62368-1 IEC (international) AV and ICT equipment safety Exact safety parts Foreign, summary only
Fire certificate for workshops Ghana National Fire Service Business premises Required for non-residential premises; steps and fees not verified Not verified; ask GNFS
Income tax and VAT GRA Your business Registration, records and thresholds See Unit 6

International items: check against the Ghana text when read.

E-waste route page. No Takoradi drop-off was verified: ask EPA Western Region and the STMA waste unit. A national e-waste collection drive was reported in 2025. Sorting guide: lead-acid batteries and lithium batteries go to their own tin or sand-filled boxes; fluorescent lamps and old tubes (mercury) stay whole; oil-filled capacitors stay sealed; boards and cables go to e-waste. Never burn.

A8 · Business pack

Item Where What to record
STMA operating permit STMA Fee: ask and record: ______
ORC registration Office of the Registrar of Companies Fee: ask and record: ______
GRA TIN and filing GRA Date and reference
GNFS certificate Fire Service Fee: ask and record: ______
Insurance An insurer Cover and cost
Bookkeeping Units 6 and 7 Month-end routine
Pricing sheet Unit 7 Mark-up and margin
12-month forecast Unit 7 Copy the table
13

Appendix B · Forms

Ask a qualified expert. Warranty, liability and customer-data wording is a legal matter: ask a qualified lawyer. For tax, check with GRA or a qualified accountant.

Use the forms in Appendix A: test-point log, rework record, incoming-parts log, complaint and return log. Add:

B1 Final quality checklist (one per job)

  • Reported fault fixed and tested
  • No new fault caused
  • Joints neat, flux cleaned
  • Case closed, screws complete
  • Battery fresh or tested; not swollen
  • Mains items: qualified person's safety checks signed
  • Job record complete, price agreed, guarantee given
  • Removed parts returned or sorted

B2 Apprentice progress log

Date Task Tier Supervisor Result Signature

B3 Safety incident report

Date What happened Injury or damage Action taken Prevented next time by
14

Appendix C · The mistake catalogue (36)

Ask a qualified expert. Many mistakes below involve shock, fire or injury. For mains work ask a qualified technician or Energy Commission-certified electrician; for injury see a doctor or nurse.

No. Mistake Cost Avoid it by
1 Wrong polarity on an electrolytic Burst part Match the stripe
2 Wrong or bigger fuse Fire Same type and rating
3 Resistance measured live Wrong reading Isolate first
4 Ohms on a charged capacitor Meter damage Discharge first
5 Diodes tested in circuit False reading Lift a leg
6 Wrong solder for the iron Poor joints Match alloy and heat
7 Too hot too long Lifted pads Right tip, short time
8 Lower-voltage capacitor Failure Same or higher voltage
9 Fine-pitch bridge Short Flux, drag, braid
10 Screwdriver discharge Burn, shock Resistor tool
11 Probes across a battery on current Blown fuse Volts range
12 Meter left on current Short Reset to OFF
13 Scope ground on a live point Short, shock Ground to ground only
14 Modified-sine reading trusted Wrong fix True-RMS meter
15 Replacing without finding the cause Repeat failure Half-split
16 Return untested Complaint Final checklist
17 Powering a mains board alone Shock Never; qualified person
18 Skipping discharge Shock Discharge and confirm
19 Wrong probe setting (1X or 10X) Wrong reading Match the scope channel
20 Compensation skipped Distorted waveform Compensate first
21 Long ground lead False ringing Short lead
22 Safety part not exact Hazard Exact replacement
23 Guessing an IC Dead board Exact part
24 Hot-air airflow too high Parts blown away Low airflow, shield
25 Heat on a battery Fire Never
26 Cleaning with flammable liquid near a hot iron Fire Iron off
27 Bypassing the optocoupler gap Lost isolation Never
28 Cutting a swollen battery Fire Refuse
29 Thin battery cable Overheat Per cable maker
30 No fuse near the battery Fire Fit one
31 Counterfeit part fitted Early failure Buy with receipts
32 Ignoring ESD Hidden damage ESD bench
33 Wrist strap on a mains supply Shock path Do not wear
34 Working alone on a hazardous job No help Buddy rule
35 Not recording Cannot trace Job card
36 Pricing without costing Loss Cost and mark-up
15

Appendix D · Worked scenarios

Teaching examples written for this book, not reports of real jobs. Prices are examples.

Ask a qualified expert. Several scenarios involve mains, batteries or injury risk. For mains work ask a qualified electrician; for injury see a doctor or nurse.

  1. The charger with a dead optocoupler. Symptom: output high, then dead. Clue: dead tests show a leaky optocoupler. Action: a qualified technician replaces it with the exact type, tests behind the isolation set-up. Lesson: feedback faults cause high outputs.
  2. The UPS that "does not hold". Symptom: drops out. Finding: tired battery, loose terminal. Action: battery side first. Lesson: do not blame the board.
  3. The LED TV with a dark screen. Symptom: sound but no picture. Finding: failed backlight strip. Decision: price the strip against a new TV; offer both.
  4. The counterfeit MOSFET. Symptom: new part fails again. Finding: wrong markings. Action: buy from a shop with receipts, test before fitting.
  5. The returned job. Symptom: back in two days. Cause: untested. Action: complaint log, free fix, final checklist added.
  6. The dangerous habit. An apprentice wears an ESD strap on a mains supply. Action: stop work, correct, record, discuss.
  7. The not worth mending. A cheap adapter is warm and unmarked. Decision: refuse, explain. Lesson: a refusal protects you and the customer.
  8. The price that lost money. A job priced without parts and time. Action: recost, raise the mark-up.
16

Appendix E · Tools and Items Glossary

This list adds the items first used at Level 3; Level 1 and Level 2 items are in their own glossaries. Local names differ from town to town: use the standard name and show the picture. The Also called column lists other common English or trade names.

Ask a qualified expert. Items marked mains, hot or battery need a qualified technician; for injury see a doctor or nurse.

Item What it is and does Also called
Analyser (logic) Records many digital lines at once logic analyser
Anti-static bag Bag that protects parts from static ESD bag
Anti-static mat Mat that drains static ESD mat
BGA Chip with balls under it ball grid array
Borescope Tiny camera on a cable to see into tight places inspection camera
Brass wool Tip cleaner
Calibration reference A known source to check an instrument
Calibration sticker Date label
Common-mode choke A coil that blocks noise on both lines
Conformal coating Thin varnish that protects a board
Current-sense resistor A small resistor that shows current shunt
Curve tracer Instrument that plots a part's behaviour (awareness only)
Differential probe Probe that measures between two points, floating isolated probe
ESD ionizer Device that neutralises static with ions
ESD tester Checks the strap and the mat
Flux (no-clean) Flux that may stay on the board
Flux (water-soluble) Flux that must be washed away
Function generator Test signal source signal generator
Fume extractor A fan with a filter that pulls fume away
HEPA filter A filter that traps very fine particles
Hot-air station Heater and blower for SMD work rework station
IGBT A power switch for high voltage
Infrared pre-heater A heater under the board that warms it evenly pre-heater
Isolation transformer Separates the unit from the mains earth
LLC converter A type of resonant supply (awareness only)
Logic probe Shows high, low, pulsing
Micro-soldering iron A fine iron for tiny work
Microscope (stereo) Magnifier with two eyepieces
MPPT controller Solar controller (referral only)
Oscilloscope Graph of voltage against time scope
PFC controller Chip that tidies the mains current
Probe (10X) Scope probe that reduces by 10
Series lamp A bulb that limits current
Solder paste Tiny solder balls in flux
Spectrum analyser Shows signals by frequency (awareness only)
Stencil Metal sheet used to apply paste
TL431 A common reference chip
TVS diode A diode that clips spikes
Thermal camera Shows heat as a picture
Torque screwdriver Screwdriver with a set tightness
UPS (line-interactive) A battery-backed supply that corrects voltage
UPS (online) A supply that always runs from the battery double-conversion UPS
Vacuum pick-up A pen that lifts small parts by suction
X capacitor A safety-marked capacitor across the mains
Y capacitor A safety-marked capacitor from mains to the case or secondary
17

Appendix F · Standards and bench library

Ask a qualified expert. Standards are not a substitute for a qualified engineer's advice. Ask a qualified technician or an Energy Commission-certified electrician before you rely on any of them.

International standards used here (summaries only; check against the Ghana text): IPC J-STD-001, IPC-A-610, IPC-7711 and IPC-7721; IEC 62368-1; IEC 61010. Books (foreign; editions and prices not verified): Electronic Troubleshooting (Tomal and Widmer); Electronic Troubleshooting and Repair Handbook (Homer Davidson); Make: Electronics (Charles Platt); Troubleshooting Analog Circuits (Bob Pease). Free: SparkFun and iFixit guides.

18

Appendix G · Index

Look up Go to
Calibration Unit 4; Appendix A6
Compliance Unit 4; Appendix A7
Counterfeits Unit 2; Appendix A5
ESD Unit 2
Final checklist Unit 4; Appendix B
Formulas Appendix A2
Hot air Unit 2; Appendix A4
Isolation set-up Unit 3
Mistakes Appendix C
Oscilloscope Unit 1; Appendix A3
Scenarios Appendix D
Switch-mode supplies Unit 3; Appendix A2
Tools Appendix E
19

Further reading and sources

Best next reads: the service manual of the devices you repair; SparkFun's free hot-air rework tutorial; the hub's Money Skills Level 2 and Entrepreneurial Thinking Level 2; and the Ghana Enterprises Agency's business advisory centres.

What this module does not cover: powered testing of mains units, CRT and microwave repair, BGA reballing, chip-level programming, solar installation and wiring, phones and computers, and Takoradi prices of parts and the Assembly's permit fee for this trade (not verified).

Every source used in this manual is listed, with links, in the Teacher Copy.

One application of the Cold-Start Learning Kit, which stays general-purpose and can build a guide on any topic in any field. Written in CTVET format; not CTVET's own electronics curriculum.