← All training manualsElectronics Repair and Soldering · read-onlyGet the PDF with Teacher Copy (GH¢50)
Training module · National Proficiency I · CTVET formatTrainee Manual

Electronics Repair and Soldering

Test first, solder neatly, mend and sell. Learn the parts, the multimeter and the soldering iron, fix small low-voltage things safely, and start your own repair table.

A soldering iron, a circuit board and a multimeter on a repair bench A bench with a blue circuit board in the middle holding a few small parts. A soldering iron rests on the board with a small curl of smoke rising. To the left a digital multimeter with a round dial and two probes. To the right a small radio with an antenna and a hand-held torch ready to be mended. 4.7 TEST FIRSTSOLDER NEATLYMEND AND SELL
Trainee name
Training centre
Start date
Instructor
Prepared by De-Graft Afful · Version 1.1.0 · November 2026
01

About this module

Every home, shop and farm in Ghana is full of small electronic things: torches, radios, speakers, chargers, power banks, solar lamps and cables. When one stops, most people throw it away or pay for a new one. A trained beginner with a soldering iron and a multimeter can often bring it back to life for a few cedis. This module teaches you to do that safely, and to earn from it.

Who it is for. People with no formal certificate, aged 18 or over. National Proficiency I is a bridging level for people with little or no formal education; holders do routine tasks under supervision. In Ghana, nobody under 18 may do hazardous work.

The one big rule of this module

You work on low-voltage things only. That means things that run on batteries or on a small safe output of a few volts, such as 3 V to 12 V. You do not open, test or repair anything that is plugged into the wall socket, and you do not open the inside of a charger, power adapter, TV or decoder. Mains electricity in Ghana can kill. Indoor wiring may legally be done only by Certified Electrical Wiring Professionals under the Electrical Wiring Regulations, L.I. 2008. If a job needs mains work, you refer it to an Energy Commission-certified electrician or to a qualified electronics technician.

Why this trade

  • Cheap, poor-quality electrical goods are common in Ghana. The Ghana Standards Authority said in 2026 that it is stepping up its fight against sub-standard electrical products. Many such goods fail early, so people need repairs and advice.
  • Ghana produces a large amount of electronic waste, about 150,000 tonnes a year according to a 2026 Greenpeace Africa brief, and the brief calls for support for repair and refurbishing work, which is a safer path than burning and dumping. Repair keeps goods out of the waste stream.

CTVET has electronics training. The Ghana TVET Service lists electronics competency-based courses at NP I and NP II, but the list we saw showed dates that ended in April 2025, so the current accreditation is not verified. The official unit list was not found online, so this module is not that curriculum. Ask CTVET or the regional TVET Service office for the current Electronics standard and match this module to it.

Electronics repair in Takoradi

The Sekondi-Takoradi Metropolitan Assembly (STMA) says master artisans must register all their trainees. Prices of parts and tools in Takoradi were not found reliably; every price in this module is labelled example. Ask three local shops before you buy.

How the module works

Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent by being watched at work, by your repairs, by answering questions, and by your logbook. About 70% of the time is practical. Every unit ends with homework and a short Check yourself, and the module ends with a 12-question quiz.

02

Unit 1 · Work safely

A soldering iron is hot enough to burn you and melt metal. Solder fume irritates your chest, lead gets onto your hands, and batteries can burn. Learn these simple rules once and you can enjoy the work for life.

Competency standard

Learning outcome Performance criteria — the trainee…
1.1 Keep to low voltage names the rule that mains-powered items are not opened; checks every item is battery or low-voltage before work
1.2 Control burns and fire rests the iron in its stand; keeps the cord clear; has water and a burn dressing near; never leaves a hot iron alone
1.3 Control solder fume works with a fan or extractor that moves fume away from the face; never leans over the joint
1.4 Control lead and flux washes hands before eating; does not eat or drink at the bench; keeps solder scraps in a box
1.5 Protect parts from static touches an earthed metal object or uses a wrist strap properly; stores parts in anti-static bags
1.6 Handle batteries and e-waste does not puncture or burn batteries; sorts waste; never burns cables

Range. All workshop work. Evidence. Observation every session; oral questions.

Ask a qualified expert. For electrical work, ask an Energy Commission-certified electrician; this module covers low-voltage things only. For fire, ask the Ghana National Fire Service or a qualified safety officer. For burns, chemical exposure, breathing problems or any injury, see a doctor or nurse. This unit teaches awareness and good practice, not medical treatment.

Low voltage only

  • Low voltage here means a battery or a small output of a few volts, for example a 9 V battery, two AA cells, or the 5 V of a USB lead. These are normally safe to touch.
  • Mains is the electricity from the wall socket. It can kill. Do not open or repair anything that plugs into the wall: TVs, decoders, kettles, irons, fans, chargers and power adapters. This course sends such jobs to a qualified technician or, for wiring, to an Energy Commission-certified electrician.
  • A charger or adapter that plugs into the wall has mains inside. You test its output lead from the outside (Unit 5) but you never open it.
  • A power bank has a lithium battery, which has its own fire risk (see Batteries below).

Check every time. Before you start, hold up each item and say aloud: battery, low-voltage lead, or mains. If it is mains, put it in the Refer box.

Heat and burns

  • The tip of a soldering iron is usually well over 300 °C. Solder melts at about 183 °C (leaded) or about 217 to 220 °C (lead-free), and irons are set higher than that.
  • Always rest the iron in its stand, never on the bench or on the work. Keep the cord out of your way. Never leave a hot iron alone, and unplug it when you leave.
  • If you burn yourself: cool the burn under cool running water for a long time, cover it with a clean dressing, and see a nurse if it is large, deep or on the face, hands or joints.
  • Never flick solder. Never hold the tip of the iron. Treat every iron as hot, even if it looks off.

Solder fume and flux

  • Most solder wire has flux inside. Flux is a rosin (pine resin) that cleans the metal. When it burns it makes smoke. In Britain, the Health and Safety Executive says rosin flux fume is a recognised cause of occupational asthma, and once the asthma has developed it can be permanent.
  • The best control is to take the fume away from your face: a small fan that blows across the work away from you, a fume extractor, or work in an open, airy place. A mask is not a substitute for extraction in regular work.
  • Do not lean over the joint and breathe the smoke. Keep your face about an arm's length from the work.
  • If you cough, wheeze or feel chest tightness while soldering, stop, go into fresh air, and see a doctor or nurse.

Lead

  • Many solders contain lead. At normal iron temperatures, lead fume is unlikely; the real route into the body is hand to mouth. Wash your hands with soap and water before eating, drinking or smoking, and at the end of work, and do not eat or drink at the bench.
  • Use lead-free solder where you can. It reduces the lead, but it still has flux, so you still need fume control.
  • Keep scraps of solder in a closed box, and sweep up solder balls. Wash your hands after sweeping.
  • Anyone who is pregnant, or who has small children at home, should take extra care and ask a doctor or nurse about lead.

Static electricity

  • Static electricity is a spark of electricity that builds up on your body or clothes. It can damage small electronic parts without you feeling anything.
  • Before touching a board or chip, touch a bare earthed metal object (for example a metal table leg that is connected to the earth). Avoid wearing nylon.
  • A wrist strap has a built-in resistor for safety and must touch your skin; it must be connected to a real earth to work. Keep parts in anti-static bags until you use them.
  • Never wear a wrist strap when working near mains power. In this course you never do, but remember the rule for later.

Batteries

  • Do not puncture, crush, open or try to repair a swollen lithium battery. Stop using it, put it in a safe place outside away from flammable things, and take it for proper disposal.
  • A swollen phone, power bank or laptop battery is a fire risk. Warning signs include a bulging case or lifted screen.
  • Never short a battery with a wire or a coin: the heat can burn you.
  • Keep batteries away from the hot iron.

E-waste and the law

  • Burning cables and plastics to get the copper releases toxic fumes. The World Health Organization (WHO) says open burning and heating are the most hazardous e-waste activities. Never burn wires, boards or batteries.
  • In Ghana, hazardous and electronic waste is regulated under the Environmental Protection Act 2025 (Act 1124), which replaced Act 917; makers and importers of electrical equipment must register with the EPA and pay an eco-levy. A fund for e-waste management is set up under the Act. Which collection points accept e-waste in Takoradi was not verified: ask the EPA Western Region office or the STMA waste unit.
  • Meanwhile, keep dead boards and batteries in labelled boxes until you can pass them to an approved collector.

Tools and items for this unit

Item What it is and what it does Size or type Also called Safety rule
Safety glasses Clear plastic eye cover; stops solder splashes and clipped wire legs reaching the eye Wrap-around, clear goggles Wear when cutting, soldering and desoldering
Fume fan A small fan that blows solder fume away from your face Desk fan or computer fan desk fan Blow across the work and away from you, never at the joint
Heat-proof mat A mat that does not burn or melt; protects the bench Silicone or ceramic board soldering mat, silicone mat Always under the iron stand
First-aid kit and burn dressing Plasters, clean dressings and a cooling burn gel Small box - Keep within reach; see a doctor or nurse for a bad burn
Fire extinguisher Cylinder that puts out small fires; the right type for a bench is a question for the Ghana National Fire Service Type: ask GNFS - Know where it is before you start; see Appendix A1
Waste boxes One lidded box for batteries, one for dead boards and cables Plastic tubs - Never burn cables; never throw batteries in the bin

Ghana mains in one line

The wall socket in Ghana is commonly given as 230 volts at 50 hertz. This was not verified in a primary Ghana text; confirm with the Energy Commission or ECG. The Ghana Standards Authority notice says household plugs and socket-outlets must meet GS IEC 60884-2-1 and 60884-2-2 from 1 January 2019, and its EasyPass datasheet lists three square pins (BS 1363) as the national plug. Voltage in a real house can be well below 230 V; ask a certified electrician (Appendix A9).

Safe or unsafe?

Your trainer describes eight scenes. For each, say safe or unsafe and why.

Safety set-up

  1. Set up your bench in an airy place, with a small fan blowing across the work away from your face.
  2. Put a heat-proof mat down and the iron stand on it. Place the iron cord so it cannot be pulled.
  3. Check the iron's cord and plug for cuts. Do not use a damaged one.
  4. Put a box for solder scraps, a box for e-waste, a box for batteries and a Refer box for mains items.
  5. Fill a bottle of water and place the burn dressing nearby. Know where cool running water is.
  6. Put on safety glasses and tie back long hair. Touch an earthed metal object.
  7. Say aloud: battery, low-voltage lead, or mains, for every item you will touch today.
  8. Write the checks in your logbook.

Look around

Visit a phone or radio repair table near you (from a safe distance, and ask permission). Note three safe things and three unsafe things you see. Do not touch anything.

Check yourself

  1. Name two items you must never open in this course.
  2. Why must you wash your hands before eating after soldering?
  3. What do you do with a swollen power bank?
03

Unit 2 · Meet the parts and the multimeter

You cannot fix what you cannot name. Learn the small parts on a board, what each one does, and how to ask a multimeter what is going on.

Competency standard

Learning outcome Performance criteria — the trainee…
2.1 Name common parts names and points to resistor, capacitor, diode, LED, transistor, switch, fuse, speaker, battery holder on a board
2.2 Read the resistor code reads 4-band resistor codes and checks them with the meter
2.3 Use a multimeter sets the dial correctly; measures DC volts, resistance and continuity
2.4 Read simple circuit drawings follows a battery, switch and lamp drawing
2.5 Care for the meter puts the dial on OFF; changes the battery; keeps the leads in good condition

Range. Low-voltage circuits and loose parts only. Evidence. Observation; oral questions; logbook of meter readings.

Ask a qualified expert. Use the meter only on batteries and low-voltage outputs in this course. Never measure the mains with a cheap meter. For any electrical work on a building, ask an Energy Commission-certified electrician. For anything involving a doctor or injury, see a doctor or nurse.

A simple circuit

A circuit is a closed path round which electricity flows, like water in a loop of pipe. A battery pushes the electricity. A switch opens or closes the path. A lamp or LED uses the energy. If the path is broken anywhere, nothing works. Almost every fault you will find is a break (open circuit) or a wrong connection (short circuit).

The common parts

Part What it does Where you see it
Resistor Limits the flow of electricity Small cylinder with coloured bands
Capacitor Stores a little electricity and smooths it Small can or disc; electrolytic ones have a stripe for the minus leg
Diode Lets electricity pass one way only Small glass or black part with a stripe
LED A diode that gives light; the longer leg is plus Lamps, torches, indicators
Transistor A small electronic switch or amplifier Black part with three legs
Switch Opens and closes the path Torches, radios
Fuse A thin wire that burns out to protect the rest Small glass tube or flat part
Speaker Turns electricity into sound Radios, speakers
Battery holder / contacts Holds the battery and connects it Torches, radios

Do not try to learn every part today. Learn to name them and to find them on a board.

Circuit symbols used in this book, numbered, with their names Twelve circuit symbols: battery, switch, lamp, resistor, capacitor, electrolytic capacitor, diode, LED, fuse, speaker, ground and NPN transistor, each with a number badge. Battery Switch Lamp Resistor Capacitor + Electrolytic ( Diode LED Fuse Speaker Ground Transistor (NP 1 2 3 4 5 6 7 8 9 10 11 12 Parts (numbers match the drawing) 1 Battery 2 Switch 3 Lamp 4 Resistor 5 Capacitor 6 Electrolytic (plus marked) 7 Diode 8 LED 9 Fuse 10 Speaker 11 Ground 12 Transistor (NPN)
Symbols you will meet. Each is drawn the same way on every diagram in this book. Source: author's drawing; shapes follow common textbook practice.

Parts on a board, with polarity

Photograph of electrolytic capacitors of several kindsA real collection of capacitors on a cream background: blue radial aluminium electrolytic capacitors with a black stripe and two legs, a very large blue can on the right with printed value and voltage, silver surface-mount electrolytic capacitors at the top, and two axial capacitors with a lead at each end at the bottom. Numbered 1 to 6.123456
Real electrolytic capacitors of several kinds. Numbers match the table. (Photo: Elcap, CC0)
No. Part What it does Safety or care rule
1 Radial electrolytic capacitor Stores charge; both legs come out of the same end Check the voltage printed on it is not lower than the circuit voltage
2 Black stripe on the can Marks the minus side Match the stripe to the minus mark on the board before soldering
3 Legs Join the part to the board Do not bend them roughly; a big can can hold charge, so do not short the legs
4 Printed value and voltage Capacitance in microfarads (µF) and the highest voltage the part can take Never fit a part with a lower voltage rating than the one you remove
5 Surface-mount electrolytic The same job, fixed flat on the board by its base Needs care and a steady hand; see the later levels
6 Axial electrolytic capacitor A lead at each end instead of both at one end Check which end is minus before you fit it
Common through-hole parts with the polarity marks numbered Five parts side by side: electrolytic capacitor with minus stripe and a shorter minus leg, ceramic disc capacitor coded 104, diode with a cathode stripe, red LED with a longer plus leg and a flat edge at the minus side, and a three-leg transistor with a flat face. - 104 Electrolytic Ceramic Diode LED Transistor 1 2 3 4 5 6 7 Parts (numbers match the drawing) 1 Stripe on can: minus side 2 New electrolytic: longer leg is plus 3 Ceramic disc: no polarity 4 Diode stripe: cathode end 5 LED longer leg: plus (anode) 6 LED flat edge: minus (cathode) 7 Transistor flat face: see data sheet
Five common parts. Polarity matters for the electrolytic capacitor, the diode, the LED and the transistor. Ceramic discs have no polarity. Source: author's drawing.
No. Part What it does Safety or care rule
1 Electrolytic capacitor stripe The stripe marks the minus leg Fit the wrong way round and it can overheat and burst; check before soldering
2 Long leg of a new electrolytic The longer leg is plus on a new part; trimmed parts lose this clue Use the stripe on the can when legs are cut
3 Ceramic disc capacitor, code 104 Stores a little charge; 104 means 100 nF No polarity; can crack if bent roughly
4 Diode stripe The stripe is the cathode end; current passes from anode to cathode Wrong way round and the circuit will not work
5 LED longer leg Plus (anode) Always use a series resistor; without one the LED burns out
6 LED flat edge Minus (cathode) Check against the lead length
7 Transistor flat face A small switch or amplifier; the three legs have different jobs Never guess the pin order: read the data sheet for that exact part
Photograph of axial resistors with colour bandsSix real axial resistors standing side by side on a white background, each a beige body with coloured bands and a wire lead at each end. The fifth from the left has three red bands and a gold band. Numbered 1 to 4 on that resistor.1234
Six real axial resistors. The fifth from the left is read as red, red, red, gold. Numbers match the table. (Photo: Evan-Amos, public domain)
No. Part What it does Safety or care rule
1 Lead (wire leg) Joins the resistor to the circuit; it has no polarity Bend it with pliers, not bare fingers; the cut end is sharp
2 Body Holds the resistive material that limits the current A resistor that is darkened or cracked has been overheated: replace it
3 Gold band Tolerance of 5 per cent; read the code from the end away from this band Never read a resistor from the gold end
4 Colour bands The first three bands give the value; here red, red, red is 2 200 ohms (2.2 kilohms) Check the value with the multimeter before you fit it
A four-band resistor and the colour code with every part numbered A resistor with two leads, a body and four bands: first digit yellow, second digit violet, multiplier red, tolerance gold. Below, ten colour swatches for digits 0 to 9. 0 black 1 brown 2 red 3 orange 4 yellow 5 green 6 blue 7 violet 8 grey 9 white Digit and multiplier colours (gold = 5%, silver = 10%) Example: yellow violet red gold = 4 7 x100 = 4,700 ohm = 4.7 k, 5% 1 2 3 4 5 6 Parts (numbers match the drawing) 1 Lead (wire leg) 2 Body (carbon or metal film) 3 Band 1: first digit 4 Band 2: second digit 5 Band 3: multiplier (zeros) 6 Band 4: tolerance (gold 5%)
A four-band resistor and the colour code. Read from the end that has no gold or silver band. Source: Rapid Resistor Codes; IEC 60062 Listing.
No. Part What it does Safety or care rule
1 Lead Wire leg that joins the resistor to the board Do not bend sharply at the body; it can break inside
2 Body Holds the resistive material; bigger bodies carry more watts A resistor too small for the job runs hot and burns the board
3 Band 1 First digit Read from the end without gold or silver
4 Band 2 Second digit Faded browns and reds are easy to mix up: measure to check
5 Band 3 Multiplier: the number of zeros Orange is three zeros, not the digit 3 alone
6 Band 4 Tolerance: gold is 5%, silver is 10% A part outside its tolerance is faulty or has changed value

Reading a resistor

A resistor's value is measured in ohms (Ω). Thousands are written k (1 kΩ = 1,000 Ω). Colour bands tell you the value.

  • Black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9.
  • On a 4-band resistor, the first two bands are digits, the third is how many zeros follow (the multiplier), and the fourth (gold or silver) is the tolerance. Read from the end opposite the gold or silver band.
  • Example: yellow, violet, red, gold = 4, 7, then two zeros = 4,700 Ω = 4.7 kΩ, with a tolerance of 5%.
  • Check by measuring with the meter set to resistance. If you are unsure which way to read, measure, and compare with both readings.

Read these resistors

  1. Brown, black, orange, gold.
  2. Red, red, brown, gold.
  3. Green, blue, yellow, gold.
  4. What colours would a 1 kΩ resistor have (4-band, gold tolerance)?

The multimeter

A digital multimeter is the tool you will use most. It measures voltage, resistance and more. Buy one with a continuity buzzer. In Ghana, basic digital multimeters were listed at roughly GH¢160 to GH¢250 on Jiji in a November 2026 search, as example prices; asking prices change often and condition varies. Compare shops and ask for a warranty.

The dial and leads.

  • The black lead goes into the socket marked COM. The red lead goes into the socket marked for voltage and resistance (VΩ). Never put the red lead in the current (A or mA) socket when measuring voltage.
  • V with a straight line is DC voltage (batteries). V with a wavy line is AC voltage (mains). In this course you use only DC voltage.
  • Ω is resistance. The symbol with sound waves (and a diode symbol) is continuity: the meter beeps if two points are connected by a very low resistance.
  • Turn the dial to OFF when you finish, to save the meter's battery.

Test the meter first. Set it to continuity, touch the two probes together: it should beep. If it does not, the meter or the leads are faulty.

Measure DC voltage (a battery)

  1. Set the dial to DC volts, at a range above the battery voltage (for a 9 V battery use the 20 V range).
  2. Touch the red probe to the plus (+) end and the black probe to the minus (−) end.
  3. Read the display. A new 1.5 V AA cell reads about 1.5 V. A cell that reads below about 1.2 V is weak (example guide, not a standard).
  4. A reading with a minus sign means the probes are the wrong way round. That is safe.

Measure resistance

  1. Remove the power: take out the battery or unplug the lead. Never measure resistance on a live circuit.
  2. Set the dial to Ω, at a range above the expected value.
  3. Touch the probes to the two legs of the part. For small parts, do not touch the metal tips with your fingers, because your body adds resistance.
  4. Read the value. Compare with the colour code.

Test continuity (is it joined?)

  1. Remove the power.
  2. Set the dial to continuity and test the meter by touching the probes together.
  3. Touch the probes to the two ends of a wire, a switch (in the ON position), or a fuse.
  4. A beep means connected. No beep means broken.
  5. Continuity is not for checking whether a wire is live. Use the voltage range for that, and only on safe low-voltage circuits.

Meter safety. Keep fingers behind the finger guards on the probes. Check the leads for cracks. Do not use the meter on mains. If the display is blank, change its battery.

Photograph of a handheld digital multimeter with test leadsA real red handheld digital multimeter with a liquid crystal display, a Hold button, a rotary selector dial, two input sockets with a black and a red test lead plugged in, and a pair of probes with metal tips lying on the left. Numbered 1 to 6.123456
A real handheld digital multimeter with its test leads and probes. Numbers match the table. (Photo: Jacek Halicki, CC BY-SA 4.0)
No. Part What it does Safety rule
1 Display Shows the reading Read the unit before the number
2 Selector dial Chooses what you measure and the range Turn it to the right setting before you touch the probes to anything
3 Input sockets with leads plugged in Connect the test leads to the meter; each socket has a different job Check the leads are in the sockets for the measurement you chose
4 Probe tips The metal points you touch to the circuit Keep your fingers behind the finger guard and off the metal
5 Test leads Carry the signal from the probes to the meter Do not use a lead with cracked insulation
6 Hold button Freezes the reading on the display Do not trust a frozen reading; take a new one
Digital multimeter with sockets, dial and probes numbered Front of a handheld digital multimeter showing the display, range dial, buttons, four sockets and two test leads ending in probes with finger guards. 12.60 V~ V= Ω mA OFF A 10A mA COM VΩ 1 2 3 4 5 6 7 8 9 10 Parts (numbers match the drawing) 1 Display 2 Range dial (turn to OFF after use) 3 Buttons (hold, range, backlight) 4 10 A socket (own fuse) 5 mA socket (own fuse) 6 COM socket: black lead 7 V-ohm socket: red lead 8 Test leads (check for cracks) 9 Finger guards on the probes 10 Metal probe tips
The parts of a handheld digital multimeter. Layouts differ between models: read your own meter's manual. Source: author's drawing; SparkFun Multimeter.
No. Part What it does Safety rule
1 Display Shows the reading and the unit; OL means over limit or an open circuit Read the unit before you read the number
2 Range dial Chooses what is measured and the range Move it to OFF when finished and never turn it while the probes touch a live circuit
3 Buttons Hold the reading, change range, light the display Do not press while measuring if you can avoid it
4 10 A socket Measures large current through its own fuse Never use for voltage; the red lead belongs here only for current
5 mA socket Measures small current through its own fuse A meter in a current socket across a battery is a short circuit
6 COM socket Common socket; the black lead always goes here Black lead stays here for every test
7 V-ohm socket The red lead goes here for volts, ohms and continuity Check the socket before every test
8 Test leads Carry the signal from the circuit to the meter Do not use leads with cracked insulation
9 Finger guards Stop your fingers sliding onto the metal tip Keep fingers behind them
10 Probe tips Touch the circuit Keep the bare metal short; never touch both tips with your hands on a live circuit

SAFETY PROTOCOL: multimeter (low-voltage use in this course) Before you start. Check the leads for cracks. Test the meter on continuity with the probes together. Put the black lead in COM and the red in V-ohm. Check that the dial is on the right range for what you measure. Know what is being measured: battery or low-voltage output only. While you work. Do not measure mains. Do not measure resistance on a powered circuit. Do not turn the dial while the probes touch the circuit. Keep fingers behind the finger guards. Touch one probe at a time to a part when you can. After. Turn the dial to OFF. Coil the leads loosely. Replace the battery if the display is faint. Report a blown fuse or cracked lead to your trainer. Emergency. If a meter smokes, drops on a live circuit or you feel a shock, remove the leads only if it is safe, switch off at the source, and call your trainer. Call 112 for a serious shock, burn or fire. Do not touch a person who is still in contact with mains: switch off at the source first. A meter's safety category (CAT) ratings are the maker's claim; use a meter rated for the place it is used. Ask a qualified expert. For anything on a building's wiring or mains, ask an Energy Commission-certified electrician.

Tools and items for this unit

Item What it is and what it does Size or type Also called Safety rule
Digital multimeter Measures volts, ohms, continuity and small current Hand-held, 3.5 digits DMM, multitester Low-voltage only in this course
Test leads and probes Insulated wires with metal tips that connect meter to circuit Red and black pair test prods Replace if cracked
Crocodile (alligator) clips Spring clips that grip a wire or a leg so you keep hands free Small, with insulating boot alligator clips, test clips Keep the boots on; clips must not touch each other
Practice board Spare board or stripboard for solder practice Small, low-voltage - Never a board from a mains item
Pencil and logbook Record readings and dates A5 book - Write before you forget

Ohm's law, the simple way

Voltage (V), current (I) and resistance (R) are linked: V = I × R. You use this to choose a resistor for an LED so it does not burn out.

Worked example (example numbers). A red LED needs about 2 V across it and 10 mA (0.01 A) through it, from a 9 V battery. The resistor must drop 9 − 2 = 7 V. R = 7 ÷ 0.01 = 700 Ω. The nearest common value is 680 Ω, which gives 7 ÷ 680 ≈ 0.0103 A, about 10 mA. These LED figures are typical foreign teaching values, not a rule for every LED; check the LED's data when you can.

LED resistor

  1. A green LED drops about 2 V and you want 10 mA from a 9 V battery. What resistor do you need? Choose the nearest of 680 Ω or 820 Ω.
  2. With two AA cells (3 V) and the same LED, what resistor value would give 10 mA?

Meter practice

  1. Test your meter: continuity beep with probes together.
  2. Measure the voltage of three batteries (a new AA, an old AA, and a 9 V). Write the readings.
  3. Read the colour code on five resistors, write the value, then measure each and compare.
  4. Test continuity on a switch (ON and OFF), a torch bulb or LED lamp, and a fuse.
  5. Draw a simple battery–switch–lamp drawing and follow the path.
  6. Turn the dial to OFF and put the meter in its case.

Parts hunt

Find an old radio or torch (not plugged in; take out the battery). Draw five parts you can see and write their names. Do not open anything that plugs into the wall.

Check yourself

  1. What does a beep on continuity tell you?
  2. Why must you never measure resistance on a live circuit?
  3. Read the value of red, violet, orange, gold.
04

Unit 3 · Solder by hand

A good solder joint is shiny, smooth and small, like a tiny volcano. A bad one is dull, lumpy or loose, and it will fail when the customer is not looking. This unit teaches you to make the good one every time.

Competency standard

Learning outcome Performance criteria — the trainee…
3.1 Choose and set up tools picks an iron, solder and flux; sets the temperature; cleans and tins the tip
3.2 Solder wire joints joins two wires with a firm, shiny joint and covers it
3.3 Solder parts to a board makes ten good joints in a row on practice board
3.4 Spot good and bad joints names the dry joint, cold joint, too much solder and bridge
3.5 Desolder removes a part with a pump or braid without lifting the track

Range. Through-hole parts and wires on practice boards and scrap boards. Evidence. Observation; the joints themselves; oral questions.

Ask a qualified expert. Solder fume and lead need care: if you cough, wheeze or feel unwell, see a doctor or nurse. Use only battery or low-voltage practice boards. For any electrical work on a building, ask an Energy Commission-certified electrician.

The tools

Tool Use
Soldering iron (25 W to 60 W) Heats the joint
Iron stand Holds the hot iron safely
Brass wool or damp sponge Cleans the tip
Solder wire 0.8 to 1 mm, with flux core Makes the joint
Desoldering pump and braid Removes old solder
Side cutters, long-nose pliers, tweezers Cut and hold
Helping hands or a small vice Holds the board
Magnifier or head lamp Lets you see the joint

Example prices (not verified). A basic electric soldering iron was listed from about GH¢61, an 80 W adjustable one about GH¢150, a 60 W kit with a multimeter about GH¢450, and stations from about GH¢1,000 on Jiji in a November 2026 search. Check each seller and the condition.

Photograph of a soldering iron in its standA real yellow and black soldering iron lying in a black stand on a wooden board: black grip on the left, yellow barrel, a metal coil guard resting in the stand, and a yellow cleaning sponge with a hole in a tray. Numbered 1 to 5.12345
A real soldering iron resting in its stand with a cleaning sponge. The tip is hidden inside the coil guard. Numbers match the table. (Photo: Bgrimer, CC BY-SA 3.0)
No. Part What it does Safety rule
1 Insulated grip The part you hold Hold only here
2 Barrel Holds the heating element behind the tip It stays hot after switching off: do not touch it
3 Coil guard A spring that holds the hot end away from the stand and your skin Return the iron to this guard every time you put it down
4 Cleaning sponge Wiped on to clean the tip Use it damp, never wet; never clean the tip with your fingers
5 Stand base Heavy tray that holds the guard and sponge Keep it flat and steady; never put it on a soft surface
Pencil soldering iron and its stand with every part numbered A pencil soldering iron with tip, heating barrel, insulated grip, strain relief and mains cord, resting in a coil stand with a base and a brass wool pot. hot end Mains-powered tool: use it only on low-voltage practice boards 1 2 3 4 5 6 7 8 Parts (numbers match the drawing) 1 Tip (replaceable, tinned) 2 Heating element inside the barrel 3 Insulated grip (hold here only) 4 Strain relief at the cable 5 Mains cord and plug 6 Stand with coil guard 7 Stand base (heavy, flat) 8 Brass-wool pot (tip cleaner)
A pencil iron resting in its stand. The tip end is the hot end. Source: author's drawing.
No. Part What it does Safety rule
1 Tip Passes heat to the joint; copper core with a plated surface Keep it tinned; never file a plated tip
2 Heating element and barrel Turns electricity into heat inside the barrel The barrel stays hot after switching off; do not touch it
3 Insulated grip The part you hold Hold here only
4 Strain relief Stops the cord bending and breaking where it enters A cracked cord is a shock risk: do not use it
5 Mains cord and plug Carries 230 V to the iron Plug in only after the iron is in its stand; check for damage every day
6 Stand with coil guard Holds the hot iron away from the bench and your skin The iron is always in the stand when not in your hand
7 Stand base Weight and flat footing; stops the stand tipping Do not put it on a sloping or soft surface
8 Brass-wool pot Cleans the tip without cooling it as much as a wet sponge Do not clean the tip with your fingers

SAFETY PROTOCOL: soldering iron Before you start. Check the cord and plug for damage. Set up a heat-proof mat, the stand, and the fume fan blowing across the work and away from your face. Put on safety glasses. Tie back long hair and loose sleeves. Have the burn dressing and water within reach. Make sure nothing flammable is near. Work only on low-voltage practice boards. While you work. The iron is always in the stand when not in use. Never walk with it. Never leave it on and unattended. Never wipe the iron on cloth or your fingers. Do not flick solder. Do not solder a part that is powered. Do not eat, drink or rub your eyes at the bench. Keep solder wire away from your mouth. After. Tin the tip, switch off, and unplug. Leave the iron in its stand to cool. Wash hands with soap and water. Sweep or pick up solder off-cuts; put them in the right box. Report a loose handle, a cracked cord or a tip that will not tin. Emergency. For a small burn, cool under running water for 10 minutes and cover it; see a doctor or nurse if it is large, blistered or on the face. If clothing or the bench catches fire, switch off at the wall if safe, use the extinguisher you were trained to use, and call 112 if the fire is not under control straight away. For a shock, switch off at the source before touching the person. Ask a qualified expert. For any fire, burn or breathing problem, see a doctor or nurse; for the right extinguisher ask the Ghana National Fire Service.

Tip shapes and what each is for

Tip Shape Use it for Note
Conical Pencil point Fine work and small pads Delivers heat over a small area
Chisel Flat blade Larger pads, wires and common bench work Delivers more heat and deposits solder evenly
Bevel (hoof) Angled cut with a flat face Drag soldering and fine-pitch work (L3) Not as common

Use the biggest tip that fits the joint: a big tip passes heat faster.

Tools and items for this unit

Item What it is and what it does Size or type Also called Safety rule
Soldering iron Heats the joint until solder melts 25 W to 60 W for beginners; more watts means faster recovery, not a hotter tip pencil iron Plug in only after placing it in the stand
Temperature-controlled station Iron whose heat you set and which holds it Dial or digital soldering station Check the set temperature before use
Solder wire Metal alloy that melts and joins; has flux inside 0.8 mm to 1 mm; leaded (Sn63Pb37) or lead-free (SAC305) solder, tin-lead wire Lead: wash hands; fume: use the fan
Flux Cleans metal so solder flows; found inside the solder wire or as paste or pen Rosin-based for hand soldering soldering flux, flux paste Rosin fume can cause asthma
Side cutters Cut wire legs close to the board Small, flush cut diagonal cutters, wire cutters Wear glasses: cut legs fly
Long-nose pliers Hold and bend wire 125 mm needle-nose pliers Do not use as a hammer
Tweezers Hold small parts Fine tip tweezer Metal tweezers conduct heat
Wire strippers Remove insulation without cutting the copper Adjustable wire stripper Cut away from your body
Helping hands A stand with clips that holds the board Two or three clips third hand Keep the board steady
Brass wool Tip cleaner that does not cool the tip Pot or pad brass sponge, tip cleaner Do not breathe the dust
Damp sponge Cleans the tip; cools it more Natural or cellulose soldering sponge Squeeze out extra water
Magnifier or head lamp Lets you see small joints Loupe or LED loupe Do not use sunlight through a magnifier near paper
Heat-shrink tubing A plastic tube that shrinks when warmed to cover a joint 2 mm to 10 mm heatshrink, sleeving Use a heat gun or the iron barrel; do not burn it

Leaded or lead-free

  • Leaded solder (tin and lead, for example 63% tin and 37% lead) melts at about 183 °C and flows easily.
  • Lead-free solder such as SAC305 melts at about 217 to 220 °C and is harder to work.
  • Sources differ on the best iron setting. Typical advice is about 315 to 370 °C for leaded solder and about 340 to 400 °C for lead-free. Start low and raise only if the solder does not flow in a couple of seconds.
  • For training, lead-free is safer on the hands. Whichever you use, control the fume (Unit 1).
Photograph of a desoldering pumpA real dark plastic spring-loaded desoldering pump lying diagonally: ribbed barrel in the middle, a short nozzle at the lower right end, a visible spring and slide in the upper section and a plunger end at the upper left. Numbered 1 to 4.1234
A real spring-loaded desoldering pump. Numbers match the table. (Photo: Ansgar Hellwig, CC BY-SA 2.0 de)
No. Part What it does Safety rule
1 Nozzle The tip you hold next to melted solder It gets hot: do not touch it
2 Barrel Holds the plunger and catches the solder Empty it into the waste box, not onto the bench
3 Spring Pushes the plunger back to make the suction Do not take the pump apart
4 Plunger end The end you press to cock the pump Keep your face away; the pump can spring
Desoldering pump and solder braid with every part numbered A spring-loaded desoldering pump with plunger knob, barrel, internal spring, thumb release button and a heat-proof nozzle, with a length of copper solder braid below. braid (wick): flat woven copper 1 2 3 4 5 6 Parts (numbers match the drawing) 1 Plunger knob (push down to cock) 2 Barrel 3 Spring inside the barrel 4 Thumb release button 5 Heat-proof nozzle 6 Solder braid (wick)
A desoldering pump and a length of solder braid. Source: author's drawing.
No. Part What it does Safety rule
1 Plunger knob Pushed down to cock the spring Keep your face away; the pump can spring up
2 Barrel Holds the plunger and catches the solder Empty the barrel into the waste box, not onto the bench
3 Spring Drives the plunger up to make the suction Do not take the pump apart
4 Release button Fires the pump Keep your thumb on the button, not the nozzle
5 Nozzle A heat-proof tip placed next to the molten solder It gets hot: do not touch it
6 Solder braid Flat woven copper that soaks up melted solder Hold it with pliers; it will be hot

SAFETY PROTOCOL: desoldering pump and braid Before you start. Wear glasses; hot solder can spit. Cock the pump away from your face. Have the iron in a stand and the mat down. While you work. Melt the solder first, then pump at once. Do not point the nozzle at anyone. Do not pump a joint you have not melted. Hold the braid with pliers, never your fingers. After. Empty the solder pellets into the waste box, tip down. Store the pump uncocked. Cut off used braid and bin it. Wash hands. Emergency. A solder splash burn: cool with running water for 10 minutes and cover it; in the eye, rinse with clean water and go to a clinic or hospital at once; call 112 if sight is affected. Ask a qualified expert. For burns and eye injuries, see a doctor or nurse.

The five steps of a good joint

  1. Clean. Wipe the tip on brass wool, then tin it: melt a little fresh solder onto the tip until it is shiny. A tinned tip passes heat well.
  2. Heat both parts. Touch the tip to the pad (the copper on the board) and the leg of the part at the same time. Count to one or two.
  3. Feed the solder. Touch the solder to the joint (where pad and leg meet), not to the iron. It should melt and flow. Use just enough to make a small cone.
  4. Remove the solder, then the iron. Take the solder away first, then the iron. Total time is about two to three seconds.
  5. Keep still. Do not move the part until the solder turns from liquid to solid (a few seconds). Then trim the leg with side cutters.

Good and bad joints

Joint What you see Why it happens
Good Shiny, smooth, small cone covering pad and leg Both parts heated; right solder
Dry or cold joint Dull, grey, lumpy or cracked Part moved while cooling, or not enough heat
Too much solder Round ball; leg hidden Too much feed
Bridge Solder joins two pads Too much solder or messy work
Lifted pad Copper peels off the board Too much heat for too long

A dry joint is the most common cause of intermittent faults. If a radio crackles when you tap it, look for dry joints.

Join two wires

  1. Strip about 10 mm of insulation from each wire without cutting the strands.
  2. Twist the strands, and tin each wire with a little solder.
  3. Cross or hook the wires, hold them still, and heat the joint. Add a little solder if needed.
  4. Let it cool. Cover the joint with heat-shrink tube or insulating tape.
  5. Tug gently. It must not move.

Solder a part to a board

  1. Push the legs of the part through the holes. Bend the legs slightly on the back to hold it.
  2. Heat the pad and leg together for one or two seconds.
  3. Feed the solder to the joint. Remove the solder, then the iron.
  4. Let it cool. Trim the leg. Look with a magnifier: shiny and smooth.
  5. Check the polarity of a diode, LED or electrolytic capacitor before you solder.

Remove a part (desolder)

  1. Put the board with the track side up.
  2. For a pump: heat the joint until the solder is liquid, place the pump nozzle on it, and press the button to suck the solder away. Repeat for each leg.
  3. For braid: lay the braid on the joint, press the iron on top, and let the braid soak up the solder.
  4. Wiggle the part gently and lift it out. Do not pull hard: you may lift the track.
  5. Clean the holes before you fit a new part.

Good or bad joint?

Your trainer holds up eight joints on a practice board. For each, say good, dry, too much, bridge or lifted, and what to do.

Ten joints, then repair

  1. Set up the bench as in Unit 1 (fan away from face, stand, mat).
  2. Clean and tin the tip. Write the iron setting you used.
  3. Solder ten resistors, one after another, onto a practice board. Trim the legs.
  4. Check each joint with a magnifier. Mark any you would redo.
  5. Desolder three of the parts and fit them back.
  6. Join two pieces of wire and cover the joint. Tug test.
  7. Wash your hands. Record in your logbook.

Joint diary

Make five more joints at home or at the centre. For each, draw it and write why it is good or bad. Bring it next class.

Check yourself

  1. Which do you heat: the solder or the joint?
  2. Name two signs of a dry joint.
  3. Why do you not pull a part hard when desoldering?
05

Unit 4 · Find faults in low-voltage things

Fault finding is a habit, not magic. Ask the same questions in the same order, test before you touch, and the fault shows itself.

Competency standard

Learning outcome Performance criteria — the trainee…
4.1 Ask the customer records what the customer says, when it started and what happened before
4.2 Look and test in order inspects, tests the battery, then the switch and leads, then the rest, with notes
4.3 Mend a torch or lamp finds and fixes a broken contact, switch, wire or bulb
4.4 Mend a lead or plug repairs a USB lead or a DC plug lead
4.5 Record the job writes the job in a job book with the fault, the fix and the price

Range. Battery or low-voltage items. Evidence. Observation; repaired items; job book.

Ask a qualified expert. Fault finding in this unit is for battery or low-voltage items only. If the fault is inside a mains-powered item, stop and refer: ask a qualified electronics technician, or an Energy Commission-certified electrician for wiring. For injury, see a doctor or nurse.

The fault-finding order

  1. Ask. What does it do, or not do? Since when? Was it dropped, wet or left in the sun? Write the answer.
  2. Look. Check for cracks, corrosion (white or green powder at battery contacts), loose wires and burn marks. Smell for burning.
  3. Power. Is the battery good? Measure its voltage with the meter. A flat battery is the most common fault.
  4. Path. Follow the path: battery contacts, switch, wires, the part that uses the power. Test continuity along each section with the battery out.
  5. Fix and re-test. Make one change at a time, then test. If you change many things at once, you will not know what fixed it.
  6. Record. Write the fault and the fix in your job book.
Battery torch (flashlight) with every part numbered Side view of a torch: clear lens, conical reflector, bulb or LED, a head contact, two AA cells in a tube, a spring, a switch button and the tail cap. AA cells (2 shown). Check the polarity marked inside the torch. 1 2 3 4 5 6 7 8 Parts (numbers match the drawing) 1 Lens (clear cover) 2 Reflector (mirror cone) 3 Bulb or LED 4 Head contact plate 5 Cells (batteries) in the tube 6 Spring (tail contact) 7 Tail cap 8 Push switch
A battery torch. The path of the current: cells to spring, switch, bulb or LED, and back through the tube. Source: author's drawing.
No. Part What it does Safety rule
1 Lens Protects the bulb and shapes the beam Do not use a cracked lens near water
2 Reflector Aims the light Do not touch with greasy fingers
3 Bulb or LED Makes the light An LED needs a series resistor; do not swap a bulb for a stronger one
4 Head contact plate Joins the bulb to the cells Clean; corrosion here is a common fault
5 Cells Supply the energy Do not mix old and new cells; remove leaking ones with gloves
6 Spring Holds the cells against the contacts A weak or rusty spring causes flicker
7 Tail cap Closes the tube and carries current back Clean the threads
8 Push switch Opens and closes the path Test with continuity after removing the cells
USB charging lead with every part numbered A USB lead with a USB-A plug on the left, a moulded boot, the cable, a second strain relief and a micro-USB plug on the right. USB-A plug micro-USB plug inside: thin wires for power and data, plus a screen 1 2 3 4 5 6 Parts (numbers match the drawing) 1 USB-A metal shell 2 Moulded boot at the plug 3 Cable jacket 4 Inner wires: power and data 5 Strain relief at micro end 6 Micro-USB metal shell
A USB lead. Inside there is a pair of power wires and a pair of data wires; colours vary, so find each by testing. Source: author's drawing.
No. Part What it does Safety rule
1 USB-A shell The plug that goes into a charger or computer Straighten bent shells only on a dead lead
2 Boot The moulded cover that takes the strain Cracked boots show where wires will break
3 Cable jacket Outer cover Do not mend a damaged jacket with tape on a lead you will sell
4 Inner wires Power and data conductors Test each by continuity; do not guess the colours
5 Strain relief at the micro end Stops the lead breaking where it flexes The most common point of failure
6 Micro-USB shell Plugs into the device Do not force it in; bent contacts cause no charging

SAFETY PROTOCOL: cutting and stripping wire, and mending a lead Before you start. Unplug the lead from everything. Put on safety glasses. Fix the lead so it will not slip. While you work. Cut away from your body. Strip only the insulation, not the copper. Do not strip more than you need. Do not test a repaired lead on a mains-powered charger until your trainer says so. After. Put off-cuts in the waste box. Check the joint by continuity before you put heat-shrink on. Record the repair on the job card. Emergency. A cut: wash and cover it, and see a nurse if deep. A burn or fire: see the soldering iron protocol; call 112 for a serious injury. Ask a qualified expert. For any injury, see a doctor or nurse.

Tools and items for this unit

Item What it is and what it does Size or type Also called Safety rule
Battery tester Shows how healthy a cell is AA/AAA or 9 V cell checker Do not test damaged cells
Contact cleaner Spray or liquid that removes dirt from contacts Small can switch cleaner, contact spray Use in fresh air; keep from flames
Isopropyl alcohol and cotton buds Cleans flux and grime from a joint 99% bottle rubbing alcohol, IPA Flammable: keep from the hot iron
Rubber eraser Cleans light corrosion from contacts Pencil eraser pencil rubber Wipe away crumbs
Cable ties Hold wires tidy Small zip ties Trim sharp ends
Insulating tape Covers wire for a temporary fix only PVC electrical tape, PVC tape Not a permanent repair

Common faults and what to do

Symptom Usual cause What to do
Dead, no light or sound Flat battery or dirty contacts Test battery; clean contacts with a rubber or a little alcohol on a cloth
Works only when tapped Dry joint or broken wire inside the lead Re-solder; replace the lead
Switch does nothing Worn contacts Test continuity; replace the switch
Corrosion powder in battery bay Leaked battery Clean carefully; wash hands; replace contacts if eaten
Torch bulb or LED dark Failed bulb, LED or broken wire Test continuity; replace the part
Lead gets warm Short circuit Stop and find the short

Leaked battery. The powder from leaked batteries can irritate the skin and eyes. Wear gloves and glasses, wipe it away, and wash your hands afterwards (author's general advice; for any injury see a doctor or nurse).

Mending a torch (battery torch)

  1. Take out the batteries. Look at the bulb or LED, the spring, the switch and the case.
  2. Clean the contacts and spring.
  3. Measure each battery with the meter. Replace weak ones.
  4. Test continuity from the battery contact through the switch (ON) to the bulb.
  5. Replace the broken part, re-solder any loose joint, and test.
  6. Check that the batteries are placed the right way (plus and minus).

Mending a lead (USB or DC plug lead)

Many leads fail where the wire bends, right next to the plug.

  1. With a meter on continuity, test each wire in the lead from one end to the other while you bend the lead gently. A beep that comes and goes is a break in that wire.
  2. Cut off the damaged part. Strip the wires and tin them.
  3. Re-solder to the plug or join to a new plug. Match the colours or mark the wires first.
  4. Check there is no connection between plus and minus (no short), then cover each joint.
  5. If the plug is moulded and cannot be opened, replace the lead. Do not use a lead that gets hot.

Plus and minus. Always check polarity before connecting to a device. Many small items are marked with a tiny symbol showing whether the centre pin is plus. A wrong connection can destroy a device.

Job-book diagnosis

Your trainer gives four symptoms. For each, write the first three checks you would do.

Mend three items

  1. For each item (a torch, a radio lead and a toy), fill a job card: customer's words, what you saw, what you tested.
  2. Follow the fault-finding order. Change one thing at a time.
  3. Fix each item. Test with fresh batteries.
  4. Write the fix, the parts used and a price (example) in the job book.
  5. Hand back and explain to your partner, who acts as the customer, in plain words.

One at home

Mend one low-voltage item that is broken at home or at a neighbour's (battery or USB lead only). Write what was wrong and what you did. If you cannot mend it, write why.

Check yourself

  1. What is the most common fault in battery items?
  2. Why change only one thing at a time?
  3. What do you do with a lead that gets hot?
06

Unit 5 · Chargers, power banks and radios from the outside

Chargers and adapters carry mains inside. You do not open them. But you can test them from the outside, find which part is at fault, and save the customer money by mending the parts you are allowed to mend.

Competency standard

Learning outcome Performance criteria — the trainee…
5.1 Know what you may and may not open refuses to open mains chargers and adapters; refers them
5.2 Test a charger output measures the DC output at the plug with the meter and compares with the label
5.3 Check cable and plug tests leads and sockets for continuity and breaks
5.4 Handle power banks safely identifies swollen batteries; refuses to open or puncture them
5.5 Mend a small battery radio finds and fixes a battery contact, switch, volume control or lead fault

Range. Output side only of chargers; battery radios and small speakers. Evidence. Observation; oral questions; job book.

Ask a qualified expert. Chargers, adapters and anything with a plug into the wall contain mains voltage and stay closed in this module: ask a qualified electronics technician, and an Energy Commission-certified electrician for building wiring. Power banks contain lithium batteries: do not open or puncture them; for any burn or injury, see a doctor or nurse.

What is in a charger?

A phone charger turns mains (230 V AC) into a small, safe direct current (for example 5 V DC) that goes down the lead. The part inside that does this is a power supply. Because the input side is mains, you never open it. You only work on the output side: the lead, the plug and the socket on the device.

Hold the charger and look at its label. It states the input (mains) and the output (for example 5 V and a current rating). The output voltage is what the meter should read.

Why a "dead" charger is often not dead

Before you blame the charger, check the cheaper parts:

  • the wall socket (try another socket, with another appliance; do not open the socket),
  • the lead (a broken wire is the most common fault),
  • the device's charging socket (dirty, bent or loose),
  • the battery of the device.

Test a charger output (safe method)

This test uses the output only, with the charger plugged into a wall socket and closed. Do it only if a trainer has approved it and the charger case is sound.

  1. Look at the charger. If the case is cracked, burnt, or the pins are bent, do not plug it in. Put it in the Refer box.
  2. Set the meter to DC volts (a range above the label's output, for example 20 V).
  3. Insert the black probe into the lead's minus side and the red probe into the plus side, where the lead plugs into the device, or at the USB contacts. For USB, the plus is the outer pin on one side and the minus the outer pin on the other; use a small test breakout or check a known USB pin diagram first. If you are not sure which pin is which, stop and ask your trainer.
  4. Plug the charger into the wall and read the voltage. Close to the label means good; zero or far off means a fault in the charger or lead.
  5. Unplug the charger from the wall before removing the probes.

If the output is dead, the lead is the first suspect. Test the lead for continuity with the charger unplugged. If the lead is fine, the fault is inside the charger: refer it, or advise the customer to buy a new charger from a reliable shop.

Fake chargers. Cheap unmarked chargers can be dangerous. The Ghana Standards Authority has stepped up its fight against sub-standard electrical products. Advise customers to buy chargers from shops that sell known brands, with a clear label, and not to use damaged ones.

Power bank (outside view) with every part numbered A power bank case with output and input ports, four level lights and a button; the lithium cells and protection board inside are drawn dashed because they must not be opened. cells + protection board inside: never open 1 2 3 4 5 6 7 Parts (numbers match the drawing) 1 Output port (USB-A) 2 Input (charging) port 3 Level lights (4) 4 Power button 5 Sealed case 6 Lithium cells inside (never open) 7 Protection board inside
The outside of a power bank. The dashed cells and board are inside the sealed case: do not open. Source: author's drawing.
No. Part What it does Safety rule
1 Output port Gives 5 V to phones and other low-voltage devices Plug in only good leads
2 Input port Takes charge from a charger Use the charger recommended by the maker
3 Level lights Show the charge A blinking pattern means different things on different brands: read the maker's guide, do not guess
4 Button Wakes the bank and shows the level A stuck button can drain the cells
5 Case Holds everything and shields the cells Do not open, press or drop
6 Lithium cells (inside) Store the energy Swollen cells are a fire risk: refuse
7 Protection board (inside) Stops over-charge, over-discharge and short circuit Do not bypass

SAFETY PROTOCOL: power banks and lithium batteries Before you start. Look at the case: swollen, hot, wet or cracked means stop. Put a swollen bank outside on a non-flammable surface away from anything that can burn. While you work. Work only on the outside: leads, ports, cleaning. Do not open, drill, press, burn or short the case. Do not charge a damaged bank. Do not leave a charging bank on a bed or sofa. After. Put a refused bank in a tin box or sand-filled container and hand it for recycling. Record the refusal. Emergency. If it smokes or gets very hot, move away. Do not use water on a burning lithium cell unless trained; leave the area, keep others away and call 112 (Ghana National Fire Service). Do not breathe the smoke. Ask a qualified expert. For fire, ask the Ghana National Fire Service; for smoke or injury, see a doctor or nurse.

Power banks

A power bank is a lithium battery with a small circuit and a USB socket. You can:

  • test the USB socket and the lead,
  • check whether it holds charge,
  • tell the customer when it is swollen, hot, or leaking, and refuse to repair it.

Do not open or puncture a power bank. A swollen battery should be taken out of use, kept outside away from flammables, and handed in for proper disposal. In Ghana, e-waste handling is governed by Act 1124; ask the EPA about collection points.

Small battery radio with every part numbered A small portable radio with a telescopic antenna, tuning window with pointer, tuning knob, volume knob, speaker grille, band switch, earphone jack and a battery door on the back. The battery door is on the back; earphone jack on the side. 1 2 3 4 5 6 7 8 Parts (numbers match the drawing) 1 Telescopic antenna 2 Tuning window and pointer 3 Tuning knob 4 Volume knob (with on-off switch) 5 Speaker 6 Band switch (AM or FM) 7 Earphone jack (side) 8 Battery door (on the back)
A small battery radio, outside view. Source: author's drawing.
No. Part What it does Safety rule
1 Telescopic antenna Picks up radio waves Do not extend it near power lines
2 Tuning window and pointer Shows the station A slipped pointer is an easy mend
3 Tuning knob Moves the tuning Do not turn with force
4 Volume knob Sets loudness; often has the on-off switch Scratchy sound when turned means a dirty control
5 Speaker Turns the signal into sound Do not poke the cone
6 Band switch Chooses AM or FM Clean with contact cleaner
7 Earphone jack Socket for earphones A dirty jack can cut the speaker
8 Battery door Opens to the cells Fit cells the right way; remove them if the radio is stored

SAFETY PROTOCOL: opening and testing a battery radio Before you start. Check that the radio runs on batteries only and has no mains lead. Take the batteries out. Put the case on a mat. While you work. Take photos and make a note of every screw. Keep screws in a tray. Touch no loose wires while the batteries are in. Do not use a mains adapter in place of the batteries. After. Test with fresh cells; wipe clean; close the case. Record the repair. Emergency. If it heats, smokes or leaks, remove the batteries with a dry tool, move it outside, wash your hands, and see a nurse if a leaking cell touched your skin or eyes. Ask a qualified expert. For any shock or skin injury, see a doctor or nurse; for building wiring, ask an Energy Commission-certified electrician.

A small battery radio

Battery radios and small speakers are good first repairs because they are low voltage. Common faults:

Symptom Likely cause Fix
Dead Flat batteries; dirty contacts Test batteries; clean contacts
Crackle when volume turned Dirty or worn volume control Clean with a little contact cleaner; replace if worn
Works only when tapped Dry joint; broken wire to the speaker or battery Re-solder; replace wire
No sound but light on Speaker wire off; broken speaker Test the speaker coil with the meter on resistance (a very low reading, a few ohms, is normal) and replace if open
Weak sound Weak batteries; dirty contacts Replace batteries; clean

Mend a battery radio

  1. Take out the batteries. Open the case carefully; keep the screws in a dish, in order.
  2. Look for loose wires, corrosion, cracked joints and burn marks.
  3. Test the batteries and the battery contacts for continuity to the board.
  4. Test the speaker: with the meter on resistance, touch the speaker terminals. A few ohms is normal; no reading means a broken coil.
  5. Re-solder any dry joints. Replace broken wires.
  6. Put the batteries back and test, with the case still open and your hands clear.
  7. Close the case. Test again. Clean the radio and hand it back.

Can I mend it?

For each item, say Mend, Refer or Refuse and why: (1) a USB lead with a broken wire; (2) a phone charger with a cracked case; (3) a battery radio that crackles; (4) a swollen power bank; (5) a TV that does not switch on; (6) a mains adapter with a burnt smell.

Charger and lead service

  1. Collect three leads and a battery radio.
  2. For each lead, test continuity of each wire while bending the lead. Mark the broken ones.
  3. Mend or replace one lead.
  4. With the trainer's approval, check the output of a sound USB charger as in the steps above.
  5. Mend the battery radio: follow the steps in this unit.
  6. Record each job in the job book.

Chargers around me

At home, look at three chargers or adapters (do not open them). Write down the input and the output on each label. Which is the most worn? Bring the details, not the charger.

Check yourself

  1. Why do we not open chargers?
  2. What is the first thing to check when a charger seems dead?
  3. What do you do with a swollen power bank?
07

Unit 6 · Make and mend

Building a small kit puts everything together: reading a drawing, placing parts the right way, soldering neatly, and testing. It also gives you something to show customers.

Competency standard

Learning outcome Performance criteria — the trainee…
6.1 Read a kit plan names each part, its value and where it goes
6.2 Build a kit places and solders all parts neatly; polarity correct
6.3 Test and fault-find tests the finished kit; finds and fixes one fault
6.4 Finish and present trims legs, cleans flux, labels, and explains the kit
6.5 Develop good repair habits keeps a job book; uses a parts box; cleans the bench

Range. A battery-powered kit such as an LED flasher, a small light or a simple radio kit. Evidence. The finished kit; observation; oral questions.

Ask a qualified expert. Kits in this unit run on a battery of 9 V or less. Do not connect them to the mains. For any building wiring ask an Energy Commission-certified electrician, and for any injury see a doctor or nurse.

Tools and items for this unit

Item What it is and what it does Size or type Also called Safety rule
Kit A bag of parts and a printed board that make one small circuit LED flasher or battery radio electronics kit Check every part against the list before you start
Breadboard A board with holes for trying a circuit without solder 400 holes protoboard Low-voltage only
Stripboard (veroboard) A board with copper strips you solder to Small veroboard Break strips cleanly
Battery holder and clip Holds cells and joins to the circuit AA x2 or 9 V clip battery box, snap Do not short the two wires
IC socket A holder that lets you change a chip without desoldering 8 pin DIP socket Do not bend the pins
Jumper wire Short wire with ends for quick links Solid or Dupont hook-up wire, Dupont lead Keep short

Choose a kit

A good first kit has: a printed circuit board, a parts list, a plan and a battery holder. Many are sold as LED flashers or lamps. Buy from a shop and ask for the parts list. Example price: not verified; ask local shops.

Build order

Always solder the lowest parts first and the tallest last. A common order is:

  1. Resistors (check the colour code and the meter).
  2. Diodes and small parts (check the stripe).
  3. Sockets for chips, if any (check the notch).
  4. Capacitors (check the plus and minus on electrolytic ones).
  5. LEDs and transistors (check legs).
  6. Battery holder and wires.
  7. Switch.

Build a kit

  1. Lay out and name each part with the plan beside you. Check the count.
  2. Read each resistor's code, tick the plan, and test one or two with the meter.
  3. Fit and solder each part in order. After each group, check the joints with a magnifier.
  4. Check polarity for every diode, LED and electrolytic capacitor before soldering.
  5. Trim the legs. Clean away flux with a little alcohol and a brush (in a ventilated place; keep alcohol away from the iron).
  6. Before connecting the battery, check with the meter that there is no short between plus and minus (the resistance should not read as zero).
  7. Connect the battery. If it does not work, switch off at once and follow the fault-finding order.

If the kit does not work

Check What to do
Battery Test voltage and polarity
Joints Look for dry joints and bridges
Polarity Check LEDs, diodes, capacitors
Resistor values Check the colour code and measure
Missing part Compare with the plan

Good repair habits

  • Keep a job book: date, customer, item, fault, fix, parts, price.
  • Keep a parts box with labelled tubs: resistors, capacitors, LEDs, switches, leads.
  • Test before you hand back. Show the customer it works.
  • Keep every removed part in a bag labelled with the job, so you can return it if asked.
  • Clean the bench at the end. Wash your hands.

Finish and present

  1. Complete the kit and test it.
  2. Write a one-page note for a customer: what it is, what it does, how to look after it.
  3. Present the kit to the class and answer two questions.
  4. Record the cost of parts (example) and time taken.

Design a fault

Write the symptoms of three faults a kit like this could have, and the order in which you would check them.

Check yourself

  1. Why solder the lowest parts first?
  2. Which parts have polarity?
  3. What do you check with the meter before connecting the battery?
08

Unit 7 · Your location, business ideas and marketing yourself

Repair is a business of trust. People leave something they need with you, so they must trust you to return it working, at a fair price, with no surprises.

Competency standard

Learning outcome Performance criteria — the trainee…
7.1 Choose a location names three good locations and one risk for a repair table
7.2 List business ideas lists five paid jobs a beginner can do safely
7.3 Price a job works out cost and price using parts, time and a margin
7.4 Market yourself writes a short advert and a WhatsApp message
7.5 Keep records and obey the law keeps a job book; knows registration and e-waste basics

Range. Small repair table or shop; low-voltage jobs only. Evidence. Oral questions; costings; marketing plan; job book.

Ask a qualified expert. Fees, permits, tax and business law change: this unit is general information, not legal or tax advice. Ask the Office of the Registrar of Companies, the Sekondi-Takoradi Metropolitan Assembly (STMA), GRA or a qualified accountant before you act. Electrical work stays with an Energy Commission-certified electrician.

Tools and items for this unit

Item What it is and what it does Safety rule
Job book Where each customer's item and fault are written Keep it dry and clean
Job card (Appendix B1) One page for each job: item, fault, price, approval Always get a signature or mark
Receipt book Gives proof of payment Carbon copy stays in the book
Parts log Records which part went into which job Keep the receipts
Tools register List of every tool and its condition Check weekly
Lockable box Keeps tools and customers' items safe Never leave a customer's item in the open

Where to set up

Good places have many people, a safe space and power for your iron:

  • near a market, lorry station, school or campus, where people carry phones, radios and torches,
  • near a mobile money or phone shop that does not repair, so you send them customers,
  • a tabletop in a shop corner (ask the owner; agree rent or a share),
  • a mobile service to farms, villages and offices, using a toolbox and a small battery iron.

Risks. Rain and dust, theft of tools and customers' items, no power, noise or smoke near neighbours. Keep a lockable box and a receipt book.

Business ideas for a beginner

  1. Mend torches, lamps, radios and small speakers.
  2. Replace leads, plugs and battery contacts.
  3. Solder cracked joints on small boards.
  4. Test and advise on chargers and power banks (from the outside).
  5. Sell tested parts and leads.
  6. Teach neighbours to test batteries and choose safe chargers.
  7. Collect and sort e-waste for approved collectors, once you have found one.

Each idea stays low-voltage. For phones and computers, see the hub's Phone Repair and Computer Hardware and Networking modules. For irons, kettles, fans and similar mains appliances, see Appliance and Generator Repair.

Price a job (example)

Item Example GH¢
Parts (new lead, plug, solder) 12
Your time (30 minutes at an example GH¢20 an hour) 10
Share of tools, electricity and rent 3
Cost 25
Mark-up of 40% on cost 10
Price 35

Mark-up is a percentage of your cost: 40% of 25 is 10. All numbers are examples; use your own costs and local prices.

Monthly money

Kofi mends 40 jobs a month at an average price of GH¢35. Parts cost GH¢12 a job. Each month he pays GH¢300 for his table, GH¢80 for power and data and GH¢120 for transport. All figures are examples. What is his profit?

Register and obey the law

  • A business name for a sole proprietor is registered at the Office of the Registrar of Companies (ORC), with a 2026 fee of GH¢130 and GH¢70 a year to renew.
  • Get an operating permit from the Assembly; STMA has an online portal and a 2025 fee-fixing list, but the fee for an electronics repair table was not verified. Ask the STMA revenue office.
  • Register your trainees if you train them.
  • Treat e-waste legally: do not burn it, keep it sorted, and ask the EPA about approved collectors under Act 1124.
  • Keep the job book: it protects you and the customer.

Market yourself

  • WhatsApp Business: a free app with a business profile, a catalogue and quick replies. Share photos of mended items with the customer's permission.
  • Google Business Profile: a free listing that lets people find you on a map.
  • Signboard: simple and clear: "Radio, torch, lead repair. Free quote."
  • Referral: ask satisfied customers to tell a friend.
  • Honesty: tell the customer when it is not worth mending.

Example advert. "Torch, radio or lead not working? Bring it. Free check, fair price, 7-day guarantee on the repair. Safe, low-voltage repairs only."

Accessibility

Persons with disabilities can do much of this work (author's judgement, not a legal statement). Bench work can be done seated. A magnifier lamp helps people with low vision. People who are deaf can work well because the work is mostly visual. People who find the resistor colours hard to see can read values with the meter. Adjust the bench height, and keep the work area clear for wheelchair access. Ask your Assembly or a disability organisation about support; the Assembly's disability fund share was not verified.

My repair table plan

  1. Choose a location and name one risk and how you would reduce it.
  2. List the tools and parts you need and the example cost of each.
  3. Work out the price of three jobs.
  4. Write an advert and a WhatsApp message.
  5. Set up a job book page.

Ask three shops

Visit three shops that sell electronics parts. Write the price of a soldering iron, a multimeter and a metre of solder. Note the differences and bring your table. Do not buy yet.

Check yourself

  1. What is mark-up?
  2. Name two places that suit a repair table.
  3. Why keep a job book?
09

Glossary

Term Meaning
Circuit A closed path for electricity
Continuity A path with very low resistance; a meter beeps
Dry joint A dull, cracked solder joint that does not conduct well
Flux Resin in solder that cleans the metal
LED Light-emitting diode
Low voltage A battery or a small safe output of a few volts
Mains Electricity from the wall socket; dangerous
Multimeter A tool that measures volts, resistance and more
Ohm (Ω) The unit of resistance
Polarity Which way round a part must go (plus and minus)
Short circuit An unwanted direct connection between plus and minus
Tinning Coating the tip or wire with a thin layer of solder
Bridge (solder) Unwanted solder joining two pads
Cathode and anode The two ends of a diode or LED
Electrolytic A capacitor with polarity
Fuse A thin link that burns out to protect a circuit
OL Over limit; the meter shows it for an open circuit
Polarity mark Stripe, long leg or flat edge showing which way round
Strain relief A cover that stops a cable breaking where it bends
Tolerance How far a part's value may be from the printed one
10

Logbook

Copy these pages into an exercise book. Your logbook is part of your assessment evidence.

  • Unit 1: safety set-up checks; low voltage rule written in my own words
  • Unit 2: resistor codes and meter readings
  • Unit 3: ten joints; good and bad joint drawings; iron setting
  • Unit 4: job cards for three repairs
  • Unit 5: lead tests; charger label notes; radio repair
  • Unit 6: kit plan, build notes, test results
  • Unit 7: price sheets; repair table plan; advert
  • Every homework, dated
11

Self-check quiz

  1. Name three kinds of things you must never open in this course.
  2. Why wash your hands after soldering?
  3. What does a beep on continuity mean?
  4. Read the resistor: yellow, violet, red, gold.
  5. Why heat the joint and not the solder?
  6. Name two signs of a dry joint.
  7. What is the first check on a dead battery torch?
  8. Why do we not open a phone charger?
  9. What do you do with a swollen power bank?
  10. Why must you never burn old cables?
  11. What does the "V with a straight line" on a meter mean?
  12. Work out the price: cost GH¢25 and a 40% mark-up.
12

Appendix A · The Bench Card Pack

One page for each job. Photocopy, laminate and pin them at your bench. Values from foreign standards are labelled international: check them against the Ghana Standards Authority or Energy Commission text when it is read.

Ask a qualified expert. These cards teach low-voltage safety and good practice. For any mains electrical work, ask an Energy Commission-certified electrician. For burns or breathing problems, see a doctor or nurse. For fire, ask the Ghana National Fire Service.

A1 · Safety card and Stop-and-Refer card

Before you start. Battery or low-voltage only. Fan on. Glasses on. Iron in its stand. Burn dressing and water near. Phone near (112).

Never. Open anything that plugs into the wall. Burn cables. Eat or drink at the bench. Leave a hot iron alone. Puncture or heat a battery.

Stop and refer when. The item has a mains plug and lead. The item has a swollen battery. You smell burning or see scorching. The customer wants a speed you cannot do safely. You are not sure which tier or class it is in.

A2 · Colour code card

Colour Digit Multiplier Tolerance
Black 0 x1
Brown 1 x10 1% (5-band)
Red 2 x100 2% (5-band)
Orange 3 x1,000
Yellow 4 x10,000
Green 5 x100,000 0.5% (5-band)
Blue 6 x1,000,000 0.25% (5-band)
Violet 7 0.1% (5-band)
Grey 8
White 9
Gold x0.1 5%
Silver x0.01 10%

(International colour code: IEC 60062; check the chart in the part's data sheet). On a 4-band resistor read two digits, then the multiplier, then the tolerance. On a 5-band resistor read three digits, then the multiplier, then the tolerance.

Preferred values. The E12 series has 12 values in each decade at 10% tolerance: 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82 (then x10, x100 and so on). The E24 series adds 11, 13, 16, 20, 24, 30, 36, 43, 51, 62, 75, 91 at 5%.

Power rating. The wattage of a resistor is not given by the colour code and is not set by a norm; common ratings are 1/8, 1/4, 1/2, 1 and 2 watts, and a larger body usually means more watts. Read the maker's data sheet. Never replace with a lower watt rating.

A3 · Marking card (capacitors and diodes)

Printed code Meaning
101 100 pF
102 1 nF
103 10 nF
104 100 nF (0.1 microfarad)
223 22 nF
473 47 nF
224 220 nF
105 1 microfarad

Method: the first two digits are the value, the third is the number of zeros, the answer is in picofarads. A letter after the code is the tolerance: J is 5%, K is 10%, M is 20%. A letter and digit before the code, for example 2A, can mean a voltage; the codes are not the same for every maker, so check the data sheet. Diode stripe = cathode. LED long leg = plus. Electrolytic stripe = minus.

A4 · Multimeter card

Test Dial Leads Dead or live Reading means
Battery voltage V with a straight line Red V-ohm, black COM Live battery (safe) Compare with Appendix A5
Resistance Ohm Red V-ohm, black COM Dead only Compare with the colour code
Continuity Beep symbol Red V-ohm, black COM Dead only Beep = joined; no beep = broken
Small current mA (DC) Red in mA socket, series with the load Live low voltage; ask your trainer Meter is part of the path

Never: mains, current range across a battery, resistance on a live circuit. OL = open or out of range.

A5 · Battery card (example values; each maker differs)

Battery Usual voltage when new Note
AA or AAA alkaline 1.5 V Below about 1.2 V is weak (example guide)
AA or AAA rechargeable (NiMH) 1.2 V Lower normal voltage
9 V (PP3) 9 V Six small cells inside
Coin cell CR2032 3 V Lithium; never swallow, keep from children
18650 lithium-ion cell 3.6 or 3.7 V nominal; full 4.2 V; cut-off about 3.0 V Sources differ by chemistry; never charge without a protection circuit
12 V lead-acid (sealed) Rested about 12.6 to 12.9 V is near full; about 12.1 V is about half Figures differ by maker and temperature; rest the battery for hours before testing

A6 · Solder card

  1. Clean and tin the tip. 2. Heat pad and leg. 3. Feed solder to the joint. 4. Solder off, then iron off. 5. Keep still. Time: 2 to 3 seconds. Leaded solder melts at about 183 C, lead-free about 217 to 220 C; settings: about 315 to 370 C leaded, 340 to 400 C lead-free; sources differ. Good joint: shiny, smooth, small cone. Bad: dull, ball, bridge, lifted pad. Tip care: tin before storing.

A7 · Formula card with worked examples

Formula Symbols Worked example (example numbers; checked by script) Common mistake
V = I x R V volts, I amps, R ohms LED: (9 V - 2 V) / 0.010 A = 700 ohm; nearest 680 ohm gives 10.3 mA Using mA as A: 10 mA = 0.010 A
P = V x I P watts 12 V at 2 A is 24 W Forgetting that a resistor must be rated above P
P = V squared / R 5 V across 100 ohm is 0.25 W (250 mW) A 1/4 W resistor at 0.25 W is at its limit: pick 1/2 W
Series resistors R = R1 + R2 + R3 220 + 470 + 100 = 790 ohm
Two resistors in parallel R = R1 x R2 / (R1 + R2) 330 and 220 ohm: 132 ohm; 10 k and 15 k: 6 k Answer is always lower than the smaller one
Wh from Ah Wh = V x Ah 3.7 V x 2 Ah = 7.4 Wh Mixing mAh with Ah
Mark-up Price = cost x (1 + mark-up) GH¢25 cost, 40% mark-up = GH¢35 Using margin instead of mark-up

Worked check for a 10,000 mAh power bank at 3.7 V: 37 Wh. A 3,000 mAh phone at 3.7 V holds 11.1 Wh. With about 70% delivered, one bank gives about 2.3 charges. (Example; real efficiency varies.)

A8 · Fault charts (symptom, check, what it means, action)

Torch does not light

Check Meaning Action
Cells new and in right way? Wrong way or flat Replace; fit correctly
Contacts bright? Corrosion or grease Clean with eraser and contact cleaner
Bulb or LED OK? Open bulb or dead LED Test continuity (bulb); replace like with like
Switch continuity? Dirty or broken switch Clean or replace
Spring and tube path? Break in return path Clean threads; add wire if needed

Radio dead or crackling

Check Meaning Action
Fresh cells? Flat cells Replace
Battery contacts and clips? Corroded Clean
Volume control noisy? Dirty Contact cleaner; turn it a few times
Crackle when tapped Dry joint Resolder the joint
No sound but hum Speaker or output Refer to Level 2

USB lead not charging

Check Meaning Action
Try another lead and charger Lead is faulty Continue
Wiggle test at the ends Break near strain relief Cut, strip, resolder
Continuity of each wire Open wire Replace the lead
Warm or smell Short Refuse

Power bank does not charge or give output

Check Meaning Action
Case swollen, hot? Failed cell Refuse and hand in for recycling
Different cable and port Cable or port fault Replace the cable
Light pattern Brand-specific Read the maker's guide; do not guess
Still dead Protection board or cells Refer; do not open

Charger or adapter seen from the outside (mains)

Check Meaning Action
Cracked case, burn marks, bent pins Danger Refuse; do not plug in
Warm without a load Fault inside Refuse
No light on the device Lead, port or charger Swap known-good lead; if the charger is suspect, refuse to open it

A9 · Ghana facts card

  • Wall supply is commonly given as 230 V, 50 Hz; not verified in a primary text: confirm with ECG or the Energy Commission.
  • Household plugs and sockets must meet GS IEC 60884-2-1 and 60884-2-2 (importers and retail from 1 January 2019); three square pins (BS 1363) is the listed national type.
  • Wiring in buildings is the work of Certified Electrical Wiring Professionals under L.I. 2008.
  • The GSA has a campaign against sub-standard electrical products. Buy plugs, cables and chargers with a verified mark.
  • Who to ask: Energy Commission (wiring, appliance labels), Ghana Standards Authority (product standards), EPA (e-waste), Ghana National Fire Service (fire), STMA (permit), ORC and GRA (business and tax). Emergency: 112.
13

Appendix B · Printable forms

Ask a qualified expert. Warranty, liability and customer-data wording is a legal matter: ask a qualified lawyer before you print a form for customers. For tax, check with GRA or a qualified accountant.

B1 · Job card

Field Write here
Job number and date
Customer name and contact (private: do not share)
Item, brand, serial number
Fault in the customer's own words
Accessories and condition on arrival
Tier or decision (mend, refer, refuse) and why
Tests done and results
Parts used (log number)
Quote and customer approval (sign or mark)
Final test result and date handed over
Guarantee offered

B2 · Parts log

Date Part (type, value, rating) Shop and receipt number Cost (GH¢) Job number

B3 · Quote and receipt

Item Parts (GH¢) Labour (GH¢) Total (GH¢)

Customer approves: ______ Date: ______ Paid: ______ Receipt number: ______

B4 · Bench safety checklist (daily)

  • Fan on and blowing away from my face
  • Glasses on
  • Heat-proof mat and stand in place
  • Burn dressing and water near
  • Waste boxes empty
  • Nothing mains-powered on the bench
  • Iron cord checked
  • First aid and 112 reminders read

B5 · Tools register

Tool Condition Date checked Fault and action
14

Appendix C · The mistake catalogue (first 12)

Ask a qualified expert. Some of these mistakes involve electrical and fire risk. For any mains electrical work, ask an Energy Commission-certified electrician; for injury, see a doctor or nurse.

No. Mistake What it looks like or costs How to avoid it
1 Wrong way round on an electrolytic capacitor Part gets hot, bulges or bursts Match the stripe to the board mark before soldering
2 Measuring resistance on a live circuit Wrong reading; meter can be damaged Remove power first
3 Meter on current range across a battery A short; blown fuse in the meter Dial on volts for a battery
4 Holding the solder to the iron, not the joint Dull, weak joint Heat the joint, then add solder
5 Too much heat for too long Lifted pad; ruined board Two to three seconds; use the right tip
6 Moving the part while the solder cools Cold joint; intermittent fault Keep still until solid
7 Leaving the iron on and unattended Burns and fire Iron in the stand; switch off when you walk away
8 Using the wrong fuse Cable or board burns Replace with the same type and rating
9 Opening a mains charger Shock risk Refuse and refer
10 Replacing parts before finding the fault Wasted parts and money Work through the order of checks
11 Handing back untested Return and lost trust Test before the customer sees it
12 Guessing a transistor's legs Part burns out Read the data sheet
15

Appendix D · Worked scenarios

These are teaching examples written for this book, not reports of real jobs. Real Ghana cases and sources are noted in the Further reading. Prices are examples.

Ask a qualified expert. For anything on a building's wiring, ask an Energy Commission-certified electrician; for injury, see a doctor or nurse.

1. The torch that blinks. Symptom: light flickers when tapped. First check: cells and contacts. Finding: corroded spring. Action: clean, test, record. Lesson: most low-voltage faults are in contacts, not in the lamp.

2. The USB lead. Symptom: charges only when held at an angle. Finding: wire broken inside the strain relief. Action: cut, strip, resolder, heat-shrink, test continuity. Lesson: the fault is usually 2 cm from the plug.

3. The swollen power bank. Symptom: case is bulging. Decision: refuse. Action: tell the customer why, put it in a non-flammable box away from anything that can burn, send it for recycling. Lesson: a refusal is also good service.

4. The old mains charger. Symptom: no light. Decision: do not open. Action: test the lead with a known-good lead; refer. Lesson: the rule is stronger than curiosity.

16

Appendix E · Tools and Items Glossary

Every item named in this book, defined. Local names differ from town to town: use the standard name and show the picture. The Also called column lists other common English or trade names. Sizes are typical and come from the maker's label or data sheet.

Ask a qualified expert. Items marked mains need an Energy Commission-certified electrician for any wiring task; for burns, chemicals or breathing problems, see a doctor or nurse.

Item What it is What it does Also called
Alligator clip Spring clip Holds a wire without hands crocodile clip, test clip
Anti-static bag Silver or pink bag Protects parts from static -
Battery clip Plastic snap with leads Joins a 9 V battery to a circuit -
Battery holder Plastic tray Holds AA or AAA cells battery box
Battery tester Meter or card Shows cell health cell checker
Bench lamp Lamp on an arm Lights the work -
Breadboard Board with holes Tries circuits without solder protoboard
Brass wool Spiral of brass Cleans the tip brass sponge, tip cleaner
Bridge (solder) A defect Unwanted solder joining two pads -
Buzzer Small sounder Makes a tone -
Cable tie Plastic strap Holds wires zip tie
Capacitor Part Stores a little charge -
Contact cleaner Spray Cleans switches and contacts switch cleaner, contact spray
Crimp tool Pliers Squeezes a connector onto wire -
DC plug Barrel plug Joins low-voltage lead to a device -
Desoldering braid Copper mesh Soaks up solder solder wick
Desoldering pump Spring suction tool Removes solder solder sucker
Diode Part Lets current pass one way -
Dupont wire Jumper with plastic ends Quick links on a breadboard -
Earphone jack 3.5 mm socket Takes earphones -
Electrolytic capacitor Part with a stripe Stores charge; has polarity -
Eraser Rubber Cleans contacts pencil rubber
Fan Small desk fan Blows fume away -
First-aid kit Box Treats minor injuries -
Flux Cleaning resin Lets solder flow soldering flux, flux paste
Fuse Thin link Burns out to protect the circuit -
Gloves Nitrile or cotton Protect hands from leaking cells -
Hand vice Small clamp Holds the work small vice
Heat gun Hot-air tool Shrinks tubing hot-air gun
Heat-proof mat Mat Protects the bench soldering mat, silicone mat
Heat-shrink tubing Plastic tube Covers a joint heatshrink, sleeving
Helping hands Stand with clips Holds the board third hand
Insulating tape PVC tape Temporary cover electrical tape, PVC tape
Iron stand Metal holder Holds the hot iron -
Isopropyl alcohol Cleaning liquid Cleans flux rubbing alcohol, IPA
Job card Paper form Records the job -
LED Light-emitting diode Gives light -
Long-nose pliers Pliers Hold and bend needle-nose pliers
Magnifier Loupe Enlarges the joint loupe
Multimeter Meter Measures volts, ohms, continuity DMM, multitester
Pliers Gripping tool Hold or bend -
Power bank Rechargeable pack Charges phones portable charger
Probe Metal tip on a lead Touches the circuit test prod
Resistor Part Limits current -
Safety glasses Eye cover Protects eyes goggles
Screwdriver set Tools Open cases -
Side cutters Cutters Trim legs diagonal cutters, wire cutters
Solder Metal alloy Makes the joint solder wire
Soldering iron Heating tool Melts solder pencil iron
Speaker Part Makes sound -
Stripboard Board with copper strips Builds circuits veroboard
Switch Part Opens or closes the path -
Test lead Insulated wire Connects meter to circuit meter lead
Tinning Technique Coats tip or wire with solder -
Transistor Part Switch or amplifier -
Tweezers Fine tongs Hold small parts tweezer
USB lead Cable Carries power and data -
Wire stripper Tool Removes insulation wire strippers
17

Appendix F · Index

Look up Go to
Battery voltages Appendix A5
Capacitor codes Appendix A3; Unit 2
Colour code Appendix A2; Unit 2
Desoldering Unit 3
Fault charts Appendix A8; Unit 4
Forms (job card, parts log) Appendix B
Formulas Appendix A7; Unit 2
Ghana facts Appendix A9; Unit 1
Meter use Unit 2; Appendix A4
Mistakes Appendix C
Power banks Unit 5
Safety Unit 1; Appendix A1
Soldering steps Unit 3; Appendix A6
Symbols Unit 2
Tools Appendix E
18

Further reading and sources

Best next reads: the manual of your multimeter; SparkFun's free multimeter tutorial; the Health and Safety Executive's pages on soldering; the next module, Electronics Repair and Soldering Level 2.

What this module does not cover: anything that plugs into the wall (TVs, decoders, kettles, irons, fans, chargers opened up), surface-mount and hot-air work, inverters and UPS, building wiring, phones and computers (see the hub's Phone Repair and Computer Hardware and Networking modules), and Takoradi prices of parts (ask local shops).

Every source used in this manual is listed, with links, in the Teacher Copy.

One application of the Cold-Start Learning Kit, which stays general-purpose and can build a guide on any topic in any field. Written in CTVET format; not CTVET's own electronics curriculum.