← All training manualsHome Appliance Care Level 2 · read-onlyGet the PDF with Teacher Copy (GH¢50)
Level 2 · National Proficiency II · CTVET formatTrainee Manual

Home Appliance Care Level 2

Check every appliance in the house, find the three that eat the most power, choose the five-star fridge over the cheap one that costs more every month, keep the gas connection tight and tested, and know the exact symptom that means "call the technician now".

Home appliance care A tidy home kitchen and laundry corner. A fridge stands a little away from the wall with a yellow energy label and stars on its door, plugged in through a voltage guard. Beside it a front-loading washing machine with its round door left slightly open to dry. A gas cooker with a blue flame; its hose runs through the wall to an LPG cylinder standing upright outside in the open air. A table fan and a water dispenser stand on the right. A woman in an apron wipes the fridge door seal with a cloth.
Trainee name
Training centre
Start date
Instructor
Prepared by De-Graft Afful · Version 1.0.0 · November 2026
01

About this module

A careful person cleans one appliance well. A skilled carer looks at the whole house: what runs, what wastes, what is dangerous, and what will break next.

Who it is for. People who have finished Home Appliance Care (Level 1), and caretakers, house managers, hostel and guesthouse staff and small shop owners who want to go further. National Proficiency II is the second level of Ghana's TVET framework: more varied work with limited supervision.

CTVET status. No CTVET programme for household appliance care was found. This module is not a CTVET curriculum.

The hard gate still applies. You never remove a casing, never open a microwave (high-voltage parts work at about 1,800 to 4,000 volts and the capacitor stays charged after unplugging), never touch refrigerant pipes, never change house wiring, sockets or breakers (that is work for a Certified Electrical Wiring Professional), and never alter gas pipework. Level 2 adds user-level tasks that makers allow the owner to do: connecting a regulator to a cylinder, replacing a screw-on inlet hose, levelling a washing machine with its feet, descaling. Where your appliance's manual differs from this book, follow the manual.

Bridge from Level 1: what you already know

  • Rating plates, watts, kWh, plugs, extension boards and the stop-and-call signs
  • Fridge placement, temperatures, cleaning, seal check, coil dusting, defrosting and power cuts
  • Front-loader and top-loader loading, filter, drawer, seal and maintenance wash
  • Cylinder outside and upright, hose and regulator checks, soapy-water test, burner cleaning, the gas-smell steps, CRM
  • Microwave, fan, iron, kettle and dispenser care
  • Waiting after power returns, voltage guards, the Energy Commission label, running cost
  • Honest care services, pricing and marketing

Level 1 did not cover whole-home checks, energy measurement and savings plans, buying advice, symptom charts, manual defrost of chest freezers, hose replacement, levelling, cylinder exchange and regulator connection, sizing guards and boards, or care plans as a business. Level 2 covers all of these.

How the module works

Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent. About 70% of the time is practical. Care steps come from appliance makers and from foreign safety bodies, labelled as foreign in the source list; Ghana rules come from the Energy Commission, the NPA, the Fire Service and PURC. Numbers marked example are invented to teach the method.

02

Unit 1 · The whole-home appliance check

Walk the house once with a checklist and you will find the next breakdown, the next fire risk and the next big bill before they happen.

Competency standard

Learning outcome Performance criteria — the trainee…
1.1 Plan a check agrees the visit, the rooms and the limits with the owner
1.2 Inspect without opening checks each appliance, cord, plug, board and the gas set-up by sight and simple tests
1.3 Rate the risks rates each finding red, amber or green
1.4 Report writes a clear check report with actions and referrals

Range. A home, a hostel floor, a guesthouse or a small shop. Evidence. Completed check sheet; check report; observation.

Ask a qualified expert. Your check is a user-level look, not an electrical or gas inspection. Refer every socket, wiring or breaker fault to a licensed electrician, every gas fault to an authorised LPG dealer or gas technician, and every appliance fault to a trained technician.

Why a check pays

A good check finds overloaded boards, damaged cords, badly placed cylinders and poorly kept appliances before they cause a fire or a breakdown. Official Ghana statistics on appliance-related home fires were not found (not verified: ask the Ghana National Fire Service).

The check sheet

Area What you look at Typical red finding
Extension boards Number of boards, what is plugged in, chains of boards Board plugged into board; iron and kettle on one board; hot or scorched board
Cords and plugs Cuts, tape, melted spots, loose pins Bare copper; melted plug
Fridges and freezers Air space, seal, coils, temperature, guard No guard and frequent low voltage; seal not gripping
Washing machine Hoses, filter, level, drain Bulging inlet hose
Gas Cylinder place, upright, hose age, regulator, soapy test Cylinder indoors; stone on regulator; bubbles in test
Small appliances Microwave door, fan grille, iron cord, dispenser Microwave door damaged; broken fan grille near children
Labels and age Star label, age, receipts, warranty Very old fridge with no label

Rate the risk

  • Red: stop now. Danger to life or property today (gas leak, damaged microwave door, burnt plug, board chains). Switch off, unplug, tell the owner at once, refer.
  • Amber: act soon. Will cause a breakdown or waste (dusty coils, weak seal, five-year-old hoses, no guard). Plan the fix within weeks.
  • Green: fine. Keep the care routine.

Whole-home check

  1. Agree with the owner: rooms, time, what you will and will not touch, and that you will unplug items briefly.
  2. Start at the main entrance and go room by room. Note each appliance: make, model, watts, star label (if any), age.
  3. Check cords, plugs and boards (Level 1 Unit 1). Photograph red findings.
  4. Check the fridge, washer, cooker and cylinder (Units 3–5 of this book) using the sheet.
  5. Do the soapy-water test on the gas connection (outdoors, valve open, knobs off).
  6. Rate each finding red, amber or green.
  7. Before you leave, tell the owner every red finding in person.
  8. Write the report (below) within a day.

The check report

A good report is short and clear:

  1. Name, address (or room) and date; who was present.
  2. Red findings first, with what you did (switched off, unplugged) and who must fix them (technician, electrician, gas dealer).
  3. Amber findings with a suggested date.
  4. Energy notes: the three biggest users (Unit 2).
  5. What you did not check (inside appliances, wiring, gas pipes) and why.
  6. Your name and signature.

Keep customers' details private: store reports safely and share them only with the owner.

Rate these findings

Rate red, amber or green and name who fixes each: (1) a fridge with dusty coils and 6 °C inside; (2) a washing-machine inlet hose dated eight years ago; (3) a stone on the regulator; (4) a TV plugged into a surge-protected board; (5) two extension boards chained, with an iron and a kettle; (6) a microwave whose door does not close firmly.

Check your own home

Do a full check of your own home or a relative's. Write the report. Bring it to class.

Check yourself

  1. What does a red finding mean and what do you do at once?
  2. Name three things your report must say it did not check.
  3. Why tell the owner red findings before you leave?
03

Unit 2 · Measure and cut energy use; buy the right appliance

The cheapest fridge in the shop can be the most expensive one you ever own. Look at the label and do the sums.

Competency standard

Learning outcome Performance criteria — the trainee…
2.1 Measure use measures or estimates daily kWh of the main appliances
2.2 Find the big users ranks appliances by monthly cost
2.3 Write a savings plan lists practical actions with expected savings
2.4 Advise a buyer compares labels, size and lifetime cost; checks receipt and warranty
2.5 Know the rules explains the label rules and the used-fridge ban

Range. Home or small shop; prepaid and postpaid meters. Evidence. Energy table; savings plan; buying comparison; oral questions.

Ask a qualified expert. For billing disputes or meter faults, contact the electricity company; do not open or interfere with the meter. For legal questions about a faulty new appliance, ask a qualified lawyer; this is general information, not legal advice.

Measure

  • Meter method: read the meter, switch off everything except one appliance for a set time, read again. The difference is that appliance's kWh. (Only practical for appliances you can run alone.)
  • Plug-in energy meter: plug it between the socket and the appliance; it shows kWh used. Leave a fridge on it for 24 hours.
  • Plate method: watts × hours a day ÷ 1,000. Good for irons, kettles, fans and TVs; not accurate for fridges, whose compressors switch on and off.
  • Label method: the Energy Commission label shows the appliance's energy consumption.

Cost it

From 1 July 2026, PURC set residential electricity at 203.7509 pesewas per kWh for the first 300 kWh a month and 269.2235 pesewas above 300 kWh, with a lifeline rate of 89.9315 pesewas for homes using only 0 to 30 kWh, plus a monthly service charge. PURC reviews tariffs every quarter; check the current rate (a later review was not found; not verified). In this book we round to GH¢2.04 a kWh for teaching.

Cut it: a savings plan

  • Fridge: air space, clean coils, good seal, correct dial, door open less; replace a very old unlabelled fridge when the owner can (see the sums below)
  • Freezer: keep it full (jugs of water fill gaps); defrost when the ice is thick
  • Iron: iron in one session, not every morning; use the right temperature
  • Kettle: boil only the water you need; descale
  • Washing machine: full loads (not overloaded); lower temperatures where the clothes allow
  • Fans and TVs: switch off at the wall when nobody is in the room
  • Lights: LED lamps; Ghana's LED and CFL lamps are covered by energy-labelling rules

Buy the right appliance

Buying checklist

  1. Size: what does the household really need (fridge volume, washing-machine kg)? Bigger costs more to buy and to run.
  2. Label: find the Energy Commission label. Regulated appliances, including fridges, washing machines, microwaves, kettles and fans, must be labelled and registered.
  3. Stars: compare models of similar size; more stars (1 to 7) means more efficient.
  4. QR code: scan it; it is created only after the model is approved and entered in the Commission's database. Note what it shows.
  5. New, not used: the Energy Commission's 2008 regulations (L.I. 1932) prohibit the manufacture, sale or importation of used fridges, freezers and air conditioners, and the Commission still seizes used fridges at the ports.
  6. Voltage: 230 V, 50 Hz, Ghana plug.
  7. Receipt and warranty: a dated receipt with the model and serial number; the warranty card filled and stamped; ask who does warranty repairs in the Western Region.
  8. Lifetime cost: price + running cost over the years you expect to keep it (exercise below).

Consumer protection. Whether Ghana has a single consumer protection law in force was not verified on an official page (ask the Ministry of Trade or a qualified lawyer). Keep receipts, warranty cards and photos, and get the seller's promises in writing.

Cheap fridge or efficient fridge? (fridge figures are example)

Fridge A (2 stars) costs GH¢4,000 and uses 1.5 kWh a day. Fridge B (5 stars), same size, costs GH¢4,600 and uses 0.9 kWh a day. Electricity GH¢2.04 a kWh; 365 days a year. (a) Yearly running cost of each? (b) Yearly saving with B? (c) How long until B's extra price is paid back? (d) Total cost of each over 5 years?

Energy table for a home

  1. List the main appliances; for each, find watts or label kWh and hours of use.
  2. Work out kWh a month and cost a month.
  3. Rank them. Circle the top three.
  4. Write three savings actions for each of the top three, and the expected saving (example figures allowed, labelled).
  5. Check your total against the household's meter or bills.

Shop survey

Visit two shops. Record five fridges: price, volume, stars, kWh, QR code works (yes/no). Bring a picture of one label.

Check yourself

  1. Why is the plate method poor for fridges?
  2. What does the QR code on the label prove?
  3. In the exercise, why is the dearer fridge cheaper in the end?
04

Unit 3 · Fridges and freezers: deeper care

Temperature logs, a proper defrost and a careful move do more for a fridge than any repair.

Competency standard

Learning outcome Performance criteria — the trainee…
3.1 Keep a temperature log logs fridge and freezer temperatures and acts on them
3.2 Defrost a manual freezer defrosts a chest freezer safely and quickly
3.3 Care for a shop freezer loads, rotates stock and plans for power cuts
3.4 Move and store a fridge prepares, moves and restarts as the manual says
3.5 Use a symptom chart sorts a symptom into user check or technician

Range. Fridge-freezers, chest freezers, display coolers in small shops. Evidence. Temperature log; observed defrost; symptom chart exercise.

Ask a qualified expert. Refrigerant work is for trained and certified refrigeration technicians only (the certification rules were not verified on an official page: ask the EPA). Never pierce, bend or cut a refrigerant pipe. For food-safety doubts, ask an environmental health officer.

The temperature log

Keep a fridge at 4 °C or below and a freezer at −18 °C. Write the reading every morning, with any power cut, on a card on the door.

Date Fridge °C Freezer °C Power cut? Action
Mon 4 −18 No None
Tue 7 −14 6 hours Kept doors shut; checked food

Manual defrost of a chest freezer

Defrost a chest freezer

  1. Plan for a morning: food will be out for some hours. Ask the owner first.
  2. Unplug. Move food into cool boxes with ice packs; keep them closed.
  3. Open the lid fully. Put towels around and a bowl under the drain plug if the freezer has one (see manual).
  4. Let the ice melt. To speed it up, place a pot of hot (not boiling) water inside and close the lid for a while; replace as it cools. No knives, screwdrivers, hammers or hair dryers.
  5. Lift out loose ice by hand or with a plastic scraper.
  6. Wash inside with warm water and a little baking soda or mild soap; rinse; dry completely.
  7. Refit the drain plug. Plug in through the guard. Wait until it is cold (check with the thermometer) before reloading.
  8. Record the date and how thick the ice was.

The shop freezer

  • Keep it full and organised; first in, first out.
  • Do not overload above the load line printed inside.
  • Keep the lid closed; use a stock list on the lid so people decide before they open it.
  • In a power cut, a full freezer holds its temperature for about 48 hours if it stays closed. Do not sell food that has thawed and been kept warm too long; when in doubt, throw it out.
  • Clean the coils more often in dusty market areas.

Moving and storing a fridge

  1. Empty it; remove or tape shelves; tape the door closed.
  2. Unplug and, if the manual says, defrost first.
  3. Move it upright if the manual says so (most do); never lay it flat unless the manual allows.
  4. On arrival, follow the manual on how long to wait before plugging in; place it with air space; level it.
  5. Long absence: empty, defrost, clean, dry and prop the door open a little so it does not smell (follow the manual).

Symptom chart: user check or technician

Symptom User checks Stop and call a refrigeration technician if…
Not cold Dial, seal, air space, coils, overloading, guard cutting power Still warm after checks; compressor runs all the time
Water on the floor Defrost drain hole blocked by food; door not closing Water keeps coming after the user checks
Ice building up fast Door not closing; weak seal Seal needs replacing
Loud knocking or clicking Fridge not level; touching the wall Clicks on and off often and does not cool
Oily patch under the pipes, burnt smell, shock None: switch off, unplug At once

Log and act

A shop's freezer log: Mon −18, Tue −16, Wed −11 (8-hour cut), Thu −9, Fri −8. The lid has frost round the edge and the shop opens it 60 times a day. (a) What is wrong? (b) What three user actions come first? (c) When do you call the technician?

Ask a shop

Ask a cold-store or drinks shop how often their freezer is defrosted, cleaned and repaired, and what a breakdown costs them.

Check yourself

  1. Name two things you must never use to remove ice.
  2. Why tape the door before moving a fridge?
  3. Who may handle refrigerant?
05

Unit 4 · Washing machines: deeper care

When a washing machine shows an error, read the manual before you call anyone. Half of the time the fix is in your hands.

Competency standard

Learning outcome Performance criteria — the trainee…
4.1 Use the symptom chart and error codes finds the code in the manual and does the user step
4.2 Replace inlet hoses replaces screw-on inlet hoses with new washers and checks for leaks
4.3 Level the machine levels it with its feet and locks them
4.4 Descale and deep clean descales and cleans as the manual says
4.5 Care for top loaders and twin tubs cleans lint filters and balances loads

Range. Front loaders, top loaders, twin tubs. Evidence. Observed hose change and levelling; symptom chart exercise.

Ask a qualified expert. Hose replacement and levelling are user tasks only when the manual allows them. Water and electricity together can kill: always unplug first. For leaks from inside the machine, burning smells, shocks or drain faults that remain after cleaning the filter, call a trained appliance technician. Taps and pipes that need changing are for a plumber.

Error codes

Most automatic machines show a code when something stops them. Electrolux names a drain error that tells the user to clean the drain pump filter. Codes differ by brand: find the code table in your manual (or the maker's website), do the user step it gives, and call the technician only if the code returns.

Symptom chart

Symptom User checks (unplug first) Call a technician if…
Will not start Door closed fully; tap open; plug and socket; child lock; guard delay Still dead
Will not drain Filter clean (Level 1); drain hose not kinked or too low/high Still will not drain
Leaks Door seal clean and not torn; drawer not blocked; inlet hose joints tight; filter tight Leak from under the machine with joints dry
Shakes, walks, bangs Load balanced; not overloaded; level; transit bolts removed on a new machine Still bangs when level and balanced
Smells Maintenance wash; seal and drawer; door left open (rarely needs a technician)
Clothes still wet Overloading; spin speed setting; filter Drum does not spin

Replace inlet hoses

Makers advise replacing inlet hoses about every 5 years, or sooner if they bulge, crack or leak, and to use new hoses rather than old ones.

Change an inlet hose (user task, if the manual allows)

  1. Unplug the machine. Close the tap.
  2. Put a towel and bowl under the joints.
  3. Unscrew the hose at the tap end, then at the machine end (by hand or with a spanner, gently).
  4. Check the new hose has its rubber washers (and filter screen, if the old one had one at the tap end).
  5. Screw the new hose on hand-tight, then a small extra turn; do not over-tighten plastic fittings.
  6. Open the tap slowly. Look and feel for drips for a few minutes. Run a short rinse and check again.
  7. Write the date on a tag on the hose and on the record card.

Level the machine

LG's guide says the floor slope under a washing machine should not be more than 1 degree and all four feet must rest firmly on the floor; adjust the feet and tighten the lock nuts. A machine that is not level vibrates and can "walk" in the spin.

Level a washing machine

  1. Unplug. Make sure the drum is empty.
  2. Put a spirit level on top, front to back and side to side.
  3. Press diagonally on the corners: does it rock?
  4. Turn the adjustable feet (up or down) until level and not rocking. Use a spanner if the manual says.
  5. Tighten the lock nut on each foot against the body.
  6. Run a short spin with a balanced load and watch.
  7. If the floor is very uneven, tell the owner: a firm, flat base may be needed (a mason's job).

Descale and deep clean

  • Descale every six months, or more often where water is hard, with an empty cycle and a washing-machine descaling product.
  • Monthly empty maintenance wash; drawer every two months.
  • Never use bleach and descaler together; follow the product label.

Top loaders and twin tubs

  • Many top loaders have a lint filter on the side of the drum or on the agitator: pull it out, empty and rinse it after washes, as the manual shows.
  • Spread the load evenly round the drum; heavy items (towels, jeans) mixed with light ones.
  • Twin tubs: balance the spin tub; drain the wash tub after use; dry it.

Which step first?

(1) A new front loader bangs on its first spin. (2) An older machine leaks at the back where the hose joins. (3) The drain error comes back the day after you cleaned the filter. (4) The machine walks forward on the tiled floor.

Code table

Find the error-code table for one washing-machine model in your area (manual or maker's website). Copy five codes and the user steps.

Check yourself

  1. What do you do first before changing a hose?
  2. What is the maximum floor slope in LG's guide?
  3. How often does Electrolux suggest descaling in hard-water areas?
06

Unit 5 · Gas cookers and LPG: deeper care

Every time you connect a cylinder, you are doing gas work. Do it the same safe way every time.

Competency standard

Learning outcome Performance criteria — the trainee…
5.1 Exchange and receive a cylinder checks a filled cylinder on receipt and transports it safely
5.2 Connect the regulator and test connects the regulator as the maker shows and does the soapy-water test
5.3 Replace a hose replaces a domestic cooker hose with approved parts
5.4 Read the flame tells a good flame from a bad one and acts
5.5 Deep clean a cooker cleans the hob, oven and grill safely

Range. Table-top and free-standing cookers; domestic cylinders; CRM exchange. Evidence. Observed connection and test (outdoors); hose change; cleaning; oral questions.

Ask a qualified expert. Gas can explode. Connecting a regulator and replacing a cooker hose are user tasks only with the parts and steps the maker or dealer gives; anything else (pipework, built-in cookers, commercial kitchens, damaged valves) is for an authorised LPG dealer or trained gas technician. In a fire or a strong leak, get out and call 112.

Receiving a filled cylinder

  • Under CRM, consumers exchange cylinders at exchange points, which the NPA says will verify cylinder weights so consumers get full value.
  • On receipt, look for: no deep dents, no heavy rust, a valve that is not bent, the seal or cap in place, a test or expiry date that has not passed.
  • Transport it upright and secured in a ventilated vehicle. Never in a closed car boot with the windows shut.
  • Do not ask for a cylinder to be overfilled: it needs room to expand.

Connect the regulator and test

Connect and test (outdoors, trainer present)

  1. Cooker knobs off. No flame, no smoking, no switches or phones near the joints.
  2. Cylinder upright in its outdoor place.
  3. Remove the cap or seal on the cylinder valve. Check the regulator's rubber washer or O-ring is in place and not cracked.
  4. Fit the regulator the way the maker or dealer shows (screw or clip type). Do not force it; do not use tools on a hand-tight fitting unless the maker says.
  5. Open the valve slowly.
  6. Soapy-water test on every joint. Bubbles: close the valve, refit, check the O-ring, retest; still bubbling: keep it off and get the part replaced by an authorised dealer.
  7. Light one burner the way the cooker manual says. Check the flame.
  8. Record the date and the result.

Replace a hose

Replace the hose whenever it is cracked or perished, and at the interval the maker or authorised dealer gives.

How often to change the hose? No official Ghana replacement interval was found (not verified: ask the NPA or the Ghana National Fire Service). Until you have an official answer, follow the maker's or dealer's interval, replace any cracked or perished hose at once, and date-tag every hose so you know its age.

Change a cooker hose (user task with approved parts)

  1. Knobs off; cylinder valve closed; cooker cool.
  2. Buy the hose and clips from an authorised LPG dealer; the hose must be marked for LPG.
  3. Loosen the clips; pull the old hose off the cooker inlet and the regulator outlet.
  4. Push the new hose fully onto each end; fit and tighten the clips.
  5. Route the hose so it does not touch hot surfaces, sharp edges or the floor where it can be stepped on.
  6. Open the valve; soapy-water test both ends; light and check the flame.
  7. Write the date on a tag on the hose and on the record card.

Read the flame

Flame Likely cause Action
Blue, steady, even Good None
Yellow, orange or lazy Dirty or blocked burner ports, misaligned caps Clean the burners (Level 1)
Lifting off the burner, noisy Caps misaligned; draught Refit caps flat; shield from wind
Yellow after cleaning, soot on pots Possible gas pressure or regulator problem Stop; authorised dealer or gas technician
Very low even on full Cylinder nearly empty or faulty regulator Exchange cylinder; then dealer

Deep clean a cooker

Hob, oven and grill

  1. Knobs off; valve closed; cool.
  2. Remove pan supports and burners; soak supports in warm soapy water.
  3. Clean burners as in Level 1 (no wooden toothpick; no oven cleaner or bleach on burners).
  4. Wipe the hob with mild soap; dry.
  5. Oven: remove shelves and trays and wash them; wipe the inside with a cleaner the manual allows; do not wet the oven burner or the spark lighter.
  6. Refit everything; open the valve; soapy-water test; light each burner and check the flame.

Hose dates

A hostel has 12 cookers. Their hose tags show: 4 fitted 6 months ago, 5 fitted 14 months ago, 3 with no tag. Hoses cost GH¢35 each and clips GH¢5 a pair (example prices). The hostel's own policy (example) is to replace every hose after 12 months. (a) Which hoses must be replaced now under that policy? (b) What will the parts cost? (c) What will you do about the hoses with no tags?

Find the dealer

Find the nearest authorised LPG outlet or CRM exchange point in your area. Ask what hoses and regulators they sell and whether CRM exchange is available. Write the answers (no phone numbers needed).

Check yourself

  1. Name three checks on a filled cylinder.
  2. Name two causes of a yellow flame.
  3. When must a cooker hose be replaced at once?
07

Unit 6 · Small appliances and power protection

A little scale, a little dust and a little surge are what kill small appliances. Size your protection to what you plug in.

Competency standard

Learning outcome Performance criteria — the trainee…
6.1 Descale irons and kettles descales as the maker says, safely
6.2 Sanitise a dispenser cleans and rinses a dispenser completely
6.3 Care for microwaves and fans keeps them clean and spots stop signs
6.4 Size boards and guards works out amps and watts and matches the device
6.5 Plan for power cuts writes a household power-cut routine

Range. Irons, kettles, dispensers, microwaves, fans; guards, surge protectors, extension boards. Evidence. Observed descaling and dispenser clean; sizing calculations; power-cut routine.

Ask a qualified expert. Descalers and cleaners are chemicals: read the label and keep them from children. For a voltage stabiliser for the whole house, an inverter or solar back-up, or any change at the breaker board, use a licensed electrician. Never open a microwave.

Irons and kettles

  • Unplug and cool before descaling.
  • Philips advises descaling every one to two months or when the calc light shows, using the iron's own calc-clean function as the manual shows; use the water type the manual names.
  • Kettles: use the descaler the manual allows; rinse and boil clean water twice, throwing it away, before use.
  • Electric kettles are among the appliances covered by Ghana's energy-labelling rules.

Dispensers

  • Clean as in Level 1: switch off, unplug, let the hot tank cool, drain, clean with a solution the manual allows, and rinse until no taste remains.
  • Keep a cleaning date on a tag; change bottles from a trusted supplier.

Microwaves and fans

  • Keep the microwave door, seal area and hinges clean; stop using it if the door is damaged or it runs with the door open.
  • Clean fans as in Level 1; a fan that hums but does not turn is for a technician.

Size the board and the guard

Amps = watts ÷ volts. With Ghana's 230 V supply:

  • A board or guard has a maximum current (amps) or power (watts) printed on it. Watts the board can take = amps × 230.
  • Add up the watts of everything you will plug in at the same time. Keep below the board's maximum.
  • Do not run heat appliances (iron, kettle, water heater, microwave) together on one board; give them a wall socket each.
  • Choose a fridge guard made for fridges and freezers, with a restart delay, and rated for the appliance (read the maker's leaflet).

Will it overload? (ratings are example)

A board is rated 13 A. (a) What is its maximum in watts at 230 V? (b) A kettle (2,000 W) and an iron (1,200 W) are plugged in together. Total watts? Overloaded? (c) A TV (100 W), decoder (20 W), fan (60 W) and phone chargers (4 × 10 W). Total? Safe? (d) How many amps does the iron alone draw?

A household power-cut routine

  • When power goes: switch off and unplug TV, decoder, computer, microwave, washing machine
  • Leave one bulb on
  • Keep fridge and freezer doors shut
  • When power returns: wait a few minutes before switching on
  • Switch on one big appliance at a time
  • In low voltage: switch off what you can; keep the fridge on its guard (ECG advice not verified on an official ECG page)
  • Generators: never run indoors; connection to house wiring only through a changeover fitted by a licensed electrician (see the hub's Appliance, TV and Generator Repair course)

Descale and size

  1. Descale an iron using its calc-clean function, following the manual.
  2. Descale a kettle with the allowed product; rinse and boil twice.
  3. Sanitise a dispenser.
  4. For one room, list everything plugged in, add the watts, and check the boards' ratings. Fix any overload by moving heat appliances to wall sockets.
  5. Write a power-cut routine card for the house and stick it near the main switch.

Board audit

Check every extension board in your home: rating, what is plugged in, total watts. Fix one overload.

Check yourself

  1. Write the formula for amps.
  2. Why not run a kettle and an iron together on one board?
  3. Who may connect a generator to house wiring?
08

Unit 7 · Your location, business, pricing and marketing

One visit earns once. A care plan earns every quarter and keeps the customer's appliances working.

Competency standard

Learning outcome Performance criteria — the trainee…
7.1 Design honest services designs a check, a care visit and a care plan within Level 2 limits
7.2 Price and cost costs and prices a visit and a plan
7.3 Choose a location picks customers and areas with good returns
7.4 Market and keep records markets honestly and keeps job and customer records

Range. The trainee's own plan. Evidence. Price list; care-plan costing; one-page plan; profile.

Ask a qualified expert. Before you register a business, sign a contract or collect money on a plan, ask the Assembly, the GRA or a qualified accountant or lawyer; this is general information, not legal advice. Refer every repair, wiring and gas-fitting job to trained and licensed people.

Services at Level 2

  • Whole-home appliance check with a written report (Unit 1)
  • Energy check and savings plan (Unit 2)
  • Buying help with label, size and lifetime-cost comparison (Unit 2)
  • Care visits: fridge, freezer defrost, washer, cooker, small appliances
  • Care plans: a set number of visits a year for a fixed price
  • Hose and guard service: inlet hoses, cooker hoses (approved parts), voltage guards
  • Referrals to trained technicians and licensed electricians you trust

Location settings that give good returns

  • Hostels near Takoradi Technical University and colleges: many fridges, irons and kettles, frequent misuse
  • Guesthouses, homestays and beach lodges at Busua, Dixcove and Akwidaa, where salt air, sand and power cuts are hard on appliances
  • Cold-store, drinks and chop-bar businesses at Market Circle, Kojokrom and Agona Nkwanta, where a dead freezer loses stock
  • Estates in Anaji, Kwesimintsim, Effia and Apremdo with working families and landlords who own many units
  • Offices, churches and schools with dispensers, fans and microwaves

Price a care plan (all figures example)

Quarterly household plan

A plan costs the customer GH¢150 a quarter and includes one visit: fridge clean and coil dusting, washer filter and drum clean, cooker burner clean and soapy test, fan and dispenser clean. Your cost per visit (cleaning materials GH¢15, transport GH¢20, a helper GH¢10) is GH¢45. (a) Profit per visit? (b) With 20 households, quarterly income, costs and profit? (c) Average profit per month? (d) If transport rises to GH¢30, what is the new profit per visit?

Records

  • Job card for each visit: date, customer, appliances, what you did, parts used, findings (red/amber/green), referrals, signature.
  • Customer file: record cards for their appliances, past reports, plan dates.
  • Money: a simple cash and MoMo book (date, in, out, what for). The hub's Money Skills course teaches this.
  • Keep customer details private and safe.

Market yourself honestly

  • WhatsApp Business profile with services and a price list; reminders before plan visits.
  • Google Business Profile for your area.
  • Signage and leaflets: "Appliance checks, care visits and care plans · Energy-saving advice · Repairs referred to trained technicians".
  • Referrals: landlords and caretakers, hostel managers, estate agents, electrical shops (buying help), technicians who send you care jobs and receive your repair referrals.
  • Proof: sample check reports (with names removed), before-and-after photos with permission, customers' written thanks.

Accessibility

Ghana's Persons with Disability Act, 2006 (Act 715) bans discrimination against persons with disabilities at work and requires services open to the public to be accessible. Ask your Assembly's social welfare office about the Assemblies' disability fund and what it supports (the current share was not verified on an official page).

Workable tasks: energy calculations and savings plans, buying help, check reports, small-appliance cleaning at a table, phone and WhatsApp bookings, stock of guards and hoses. Adjustments: a partner for lifting and moving heavy appliances; a table-height workstation; large-print or audio check sheets; talking calculators and phone apps; picture job cards for deaf workers. Ask the person what works best.

My Level 2 plan

  1. Write a price list for a check, three care visits and one plan.
  2. Cost one plan for 20 customers.
  3. Choose your first area and three target customers.
  4. Write your WhatsApp profile text.
  5. Design your job card.

Pilot visit

Do one full check and care visit for a relative or neighbour, using your job card. Ask for honest feedback.

Check yourself

  1. Why is a care plan better for a small business than single visits?
  2. What goes on a job card?
  3. Name two adjustments for a worker with low vision.
09

Glossary

Term Meaning
Whole-home check A room-by-room user-level look at every appliance, cord, board and the gas set-up
Red / amber / green Danger now / act soon / fine
Plug-in energy meter A device between socket and appliance that shows kWh used
Lifetime cost Purchase price plus running cost over the years of use
Lifeline tariff PURC's lower electricity rate for homes using 0–30 kWh a month
Manual defrost Switching off and melting the ice by hand in a freezer that does not defrost itself
Error code A code on a washing machine's display that points to a problem
Lock nut The nut that holds a levelling foot in place
O-ring A rubber ring that seals a gas or water joint
Care plan A fixed price for a set number of care visits a year
Job card The record of one visit
10

Logbook

Copy these pages into an exercise book. Your logbook is part of your assessment evidence.

  • Unit 1: two check sheets and reports
  • Unit 2: energy table; savings plan; buying comparison; shop survey
  • Unit 3: two-week temperature log; defrost record; symptom-chart exercise
  • Unit 4: hose change record; levelling record; error-code table
  • Unit 5: cylinder receipt check; connection and test record; hose change; cooker deep clean
  • Unit 6: descaling records; dispenser clean; board audit; power-cut routine card
  • Unit 7: price list; plan costing; job card; pilot visit
  • Every homework, dated
11

Self-check quiz

  1. What do you do at once with a red finding?
  2. What are the three ways to measure an appliance's energy use?
  3. What does the QR code on the Energy Commission label show?
  4. Since when has the ban on used fridges been enforced?
  5. Name two tools you must never use to defrost.
  6. What is the first thing to do before changing an inlet hose?
  7. Why lock the nuts after levelling?
  8. Name three checks on a filled cylinder.
  9. What does a yellow flame after cleaning suggest?
  10. When must a cooker hose be replaced at once?
  11. A board is rated 10 A. What is its maximum in watts at 230 V?
  12. Give two parts of a household power-cut routine.
12

Further reading and sources

Best next reads: Home Appliance Care (Level 1); your appliances' manuals and error-code tables; the Energy Commission's label guidance; Home Appliance Care Level 3.

What this module does not cover: repair; refrigerant; wiring; gas pipework and commercial kitchens; air conditioners (Refrigeration and Air-Conditioning Basics); generators (Appliance, TV and Generator Repair); fire fighting and escape plans (Home Fire and Gas Safety).

Every source used in this manual is listed, with links, in the Teacher Copy.

One application of the Cold-Start Learning Kit, which stays general-purpose and can build a guide on any topic in any field. Written in CTVET format; not a CTVET curriculum.