← All training manualsHome Appliance Care · read-onlyGet the PDF with Teacher Copy (GH¢50)
Training module · National Proficiency I · CTVET formatTrainee Manual

Home Appliance Care

Unplug before you clean. Keep the gas cylinder outside. Give the fridge room to breathe. Wait before you switch on after "light off". Read the energy label before you buy. Small habits, done every week, keep your appliances working for years and your bills lower.

Home appliance care A tidy home kitchen and laundry corner. A fridge stands a little away from the wall with a yellow energy label and stars on its door, plugged in through a voltage guard. Beside it a front-loading washing machine with its round door left slightly open to dry. A gas cooker with a blue flame; its hose runs through the wall to an LPG cylinder standing upright outside in the open air. A table fan and a water dispenser stand on the right. A woman in an apron wipes the fridge door seal with a cloth.
Trainee name
Training centre
Start date
Instructor
Prepared by De-Graft Afful · Version 1.0.0 · November 2026
01

About this module

An appliance bought with hard-earned money should give years of service. Most early breakdowns come from small things: a fridge pushed against the wall, a washing machine overloaded, a filter never cleaned, a surge when the light comes back. This module teaches you those small things.

Who it is for. Householders, house helps, caretakers, hostel and guesthouse staff, shop owners who keep a fridge or freezer, young people who want a first skill, and persons with disabilities. National Proficiency I is the first level of Ghana's TVET framework, for routine tasks done under supervision.

Why appliance care matters

  • Power can come back after a cut with brief surges or spikes that damage appliances and electronics.
  • Ghana runs a mandatory energy label so buyers can choose appliances that use less power.
  • The NPA warns that putting stones on leaking regulators is dangerous and has contributed to fire outbreaks, and tells users to store cylinders in well-ventilated places.

CTVET status. No CTVET programme for household appliance care was found; CTVET's trade programmes cover repair trades such as electronics and refrigeration, not user care. This module is not a CTVET curriculum. It follows CTVET's format.

The hard gate: you care for appliances; you do not repair them. In this course you never:

  • remove a cover, back panel or casing of any appliance;
  • open a microwave: its high-voltage parts work at about 1,800 to 4,000 volts and its capacitor stays charged after unplugging;
  • touch the gas (refrigerant) pipes of a fridge, freezer or air conditioner, or cut or bend them;
  • change, repair or extend house wiring, sockets or breakers: that is work for a Certified Electrical Wiring Professional licensed by the Energy Commission;
  • alter gas pipes, burners or regulators beyond the user tasks in Unit 4.

If an appliance sparks, smells of burning, gives a shock, leaks gas or water it should not, or will not work after the user checks in this book: switch off, unplug, and call a trained technician.

How the module works

Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent from what your assessor sees, asks and reads in your logbook. About 70% of the time is practical.

Where the guidance comes from. Ghana's rules come from the Energy Commission, the National Petroleum Authority, the Ghana National Fire Service and the Public Utilities Regulatory Commission. Care steps come from appliance makers (Electrolux, Samsung, LG, Whirlpool, KitchenAid, Philips) and from foreign safety bodies (the US Food and Drug Administration, the US Consumer Product Safety Commission, Energy Safe Victoria in Australia). These are foreign sources, labelled as such. Their care advice fits any appliance of the same type, but your own appliance's manual always comes first.

Honesty rule. Numbers marked example were invented to teach the method. Where a Ghana fact could not be found, the book says not verified.

02

Unit 1 · Know your appliances and the safety rules

Before you clean or move an appliance, know three things: what it is, how much power it uses, and where its limits are.

Competency standard

Learning outcome Performance criteria — the trainee…
1.1 Read the plate and the manual finds the rating plate, reads volts and watts, and finds the care section of the manual
1.2 Use plugs, sockets and extension boards safely checks plugs and cords, avoids overloading and daisy-chaining
1.3 Keep within the user's limits names the hard-gate tasks and the danger signs that mean "stop and call"
1.4 Keep an appliance record fills an appliance record card for three appliances

Range. Common household appliances in a home, hostel or shop. Evidence. Rating-plate exercise; plug and cord check; record cards; oral questions.

Ask a qualified expert. For any electrical fault, sparks, burning smell, shock or wiring work, use a licensed electrician or a trained appliance technician. Do not attempt work you are not trained and authorised to do.

The rating plate and the manual

Every appliance has a rating plate (a sticker or metal plate, usually at the back or inside the door). It shows the maker, the model number, the voltage, the frequency and the power in watts (W). Ghana's mains supply is 230 volts at 50 hertz, and Ghana uses plug types D and G. An appliance made for 110 volts (for example, some brought from the USA) must not be plugged straight into a Ghana socket.

The manual (user's guide) tells you how to install, use and clean that exact model. If you lost it, search the model number on the maker's website: most makers publish manuals free. Where this book and your manual differ, follow your manual.

  • Watts tell you how hard the appliance pulls power. An iron or a kettle pulls far more than a fan.
  • kWh (kilowatt-hours) is what your meter counts: 1,000 watts for 1 hour = 1 kWh.
  • Model number is what a technician or shop needs to find parts and manuals.
  • Serial number and purchase receipt are what you need for a warranty claim.

Plugs, sockets and extension boards

  • Use extension cords only when you must, and only for a short time; do not overload a cord or a power strip; replace cracked or worn cords; do not buy counterfeit goods, and look for a certification label from an independent testing body. In the USA, about 2,000 home fires a year are linked to cords and plugs.
  • Buy cables, plugs and extension boards from a trusted shop; avoid counterfeit goods. Ghana Standards Authority approval marks were not checked in this book (not verified: ask the GSA).
  • Never plug one extension board into another ("daisy-chaining").
  • High-power appliances (iron, kettle, microwave, water heater) go straight into a wall socket, one at a time where possible.
  • Pull the plug, not the cord.
  • Keep cords out of walkways, away from water and from hot surfaces such as the iron's soleplate and the cooker.

Plug and cord check (unplugged)

  1. Unplug the appliance at the wall. Switch the socket off too.
  2. Look along the whole cord: cuts, cracks, melted spots, tape repairs, bare copper. Any of these: tag "DO NOT USE" and report.
  3. Look at the plug: cracked case, loose pins, burn marks, a plug that feels hot after use. Report it.
  4. Look at the socket face: scorch marks or a loose fit. Report it to the owner: sockets are for a licensed electrician.
  5. Count what is plugged into each extension board. Remove any board plugged into another board.
  6. Write what you found on the record card.

The user's limits: stop and call

Stop, switch off at the wall, unplug, and call a trained technician if you see:

  • sparks, smoke, a burning or "fishy" plastic smell;
  • a tingle or shock when you touch the appliance;
  • a cord or plug that is hot, melted or cracked;
  • water leaking from where it should not (under a fridge or around a washing machine's base);
  • a microwave that runs with the door open or a door that will not close firmly;
  • a gas smell that does not go away after you close the cylinder valve (Unit 4);
  • an appliance that trips the breaker again and again.

Who to call. A technician trained in appliance repair (the hub's Appliance, TV and Generator Repair course) or in refrigeration (the hub's Refrigeration and Air-Conditioning Basics course); for sockets and wiring, a Certified Electrical Wiring Professional. In an emergency (fire, a person shocked or burnt), call 112.

The appliance record card

Keep one card (or one page in an exercise book) for each big appliance:

Item Example entry
Appliance and room Fridge-freezer, kitchen
Make and model (from rating plate)
Watts / star rating (from plate and energy label)
Date bought and where (from receipt)
Warranty ends (from warranty card)
Care done (date, what) 12 Jan: coils dusted, seal cleaned
Problems and who fixed them 3 Mar: fridge guard replaced

Read the plate

A rating plate says: "230V~ 50Hz 1200W". (a) Can it be used in Ghana? (b) How many kWh does it use in 2 hours? (c) Another plate says "110–120V 60Hz". What must you not do?

Your home's appliances

List every appliance in your home with its watts (from the plate). Mark the three biggest users. Fill one record card.

Check yourself

  1. Where do you find the watts of an appliance?
  2. Name two things you must never do with an extension board.
  3. Name three signs that mean "stop and call a technician".
03

Unit 2 · Fridges and freezers

A fridge works day and night for ten years or more. Give it air, a clean seal and steady power, and it will thank you with low bills and safe food.

Competency standard

Learning outcome Performance criteria — the trainee…
2.1 Place a fridge or freezer correctly leaves air space, keeps it level and away from heat
2.2 Set and check temperatures uses a thermometer to check the fridge and freezer
2.3 Load and clean loads for air flow; cleans the inside and the door seal
2.4 Do the user maintenance checks the seal, dusts the coils (unplugged) and defrosts as the manual says
2.5 Manage power cuts keeps doors closed and judges food safety after a cut

Range. Fridge-freezer, chest freezer, small bar fridge. Evidence. Observed cleaning and seal check; temperature log; oral questions.

Ask a qualified expert. For a fridge that does not cool, leaks oil or gas, makes a loud clicking or buzzing, or gives a shock, call a trained refrigeration technician. Never touch the refrigerant pipes. For food that may have gone bad, follow the food-safety rule below and ask a health worker if someone becomes ill.

Place it right

  1. Air space. The black coils (condenser) at the back or under the fridge throw out heat. Leave space between the coils and the wall: as much as your manual says.
  2. Away from heat. Not beside the cooker, not in direct sun, not against a hot zinc wall.
  3. Level and firm. Use the front feet to level it so the door closes by itself.
  4. On a guard. Plug it through a voltage guard (Unit 6).
  5. After moving or delivery, follow the manual on how long to leave it standing before you switch on (not given in the sources read; check the manual).

Temperatures

Keep the fridge at 4 °C (40 °F) or below and the freezer at −18 °C (0 °F). The dial numbers (1 to 7, or "min" to "max") are not temperatures: put a cheap fridge thermometer in the middle shelf and check after a few hours.

Load and clean

  • Leave space between items so cold air can move.
  • Do not put hot pots straight in: let food cool a little first (quickly, not all day).
  • Cover food; raw meat and fish on the lowest shelf in a dish.
  • Do not block the air vents inside.
  • Open the door less often and close it quickly.

Clean a fridge (inside, seal and coils)

  1. Unplug the fridge at the wall. Move food to a cool box.
  2. Remove shelves and drawers. Wash them in warm water with mild dish soap; dry.
  3. Wipe the inside with a soft cloth and warm soapy water; then a cloth with clean water; dry. Do not use scouring powder or sharp tools.
  4. Wipe the door seal (the rubber gasket) all round, inside the folds. Sticky spills left on the seal make it stick and tear.
  5. Seal check: close the door on a strip of paper at several places round the door. If it slides out with almost no pull, the seal is not gripping there. Report a weak seal: replacing it is a technician's job.
  6. Coils: with the fridge still unplugged, gently pull it out and brush or vacuum the dust off the coils at the back or bottom. Do it as often as your manual says, and more often in dusty places. Do not bend the pipes.
  7. Push it back, leaving the air space. Plug in through the guard. Put food back when it is cold again.
  8. Record the date on the card.

Defrosting

Many modern fridges are "frost-free" and defrost themselves. Older ones and most chest freezers need manual defrosting when the ice is thick. Follow the manual. In general: unplug, empty, leave the door open with towels and a tray to catch water, let the ice melt by itself. Never chip ice with a knife or screwdriver: you can pierce the gas pipe in the wall of the freezer, and then the appliance needs a refrigeration technician.

Power cuts and your food

  • Keep the doors closed. A fridge keeps food cold for about 4 hours if the door stays closed; a full freezer holds its temperature for about 48 hours, a half-full one about 24 hours.
  • Throw away perishable food (meat, fish, milk, eggs, leftovers) that has been above 4 °C for 4 hours or more; some US guidance uses 2 hours, so be careful.
  • Frozen food that still has ice crystals, or is at 4 °C or below, can be cooked or refrozen.
  • Never taste food to test it. When in doubt, throw it out.
  • When power returns, do not rush to switch on: see Unit 6.

Used fridges. The Energy Commission's 2008 regulations (L.I. 1932) prohibit the manufacture, sale or importation of used fridges, used freezers and used air conditioners; the Commission reports seizing 1,246 used fridges and 1,525 used air conditioners at the Tema and Takoradi ports in 2024 alone. Old fridges use more power. See Unit 6 and Level 2.

Thermometer log

You check a fridge three mornings: 7 °C, 6 °C, 5 °C. The freezer reads −12 °C. (a) Which readings are too warm? (b) Name three user checks before calling a technician.

Fridge week

Put a thermometer in a fridge at home or in a shop. Record the temperature every morning for a week and the number of power cuts.

Check yourself

  1. What temperatures should a fridge and a freezer keep?
  2. Why must you never use a knife to remove ice?
  3. How long does a full freezer hold its temperature in a power cut if the door stays shut?
04

Unit 3 · Washing machines: top loader and front loader

Most washing-machine "faults" are a sock in the filter, too many clothes, or too much soap.

Competency standard

Learning outcome Performance criteria — the trainee…
3.1 Tell the types apart names top loader (agitator or impeller, twin tub) and front loader, and their care needs
3.2 Load and dose correctly empties pockets, sorts, does not overload or overdose
3.3 Clean after use leaves door and drawer open; wipes the door seal
3.4 Do the monthly care cleans the filter, the detergent drawer and runs a maintenance wash, as the manual says
3.5 Check hoses and position checks hoses for bulges and leaks; checks the machine stands level

Range. Front-loading automatic, top-loading automatic and twin-tub machines. Evidence. Observed filter clean and drawer clean; loading demonstration; oral questions.

Ask a qualified expert. For a machine that gives a shock, smells of burning, leaks from inside, or will not drain after you clean the filter, call a trained appliance technician. Never open the back or top panel. Never use a machine with a damaged cord.

The types

Type How you load Care points
Front loader Round glass door at the front Rubber door seal traps water and dirt; drain pump filter at the bottom front; uses less water
Top loader (automatic) Lid on top Lint filter in the drum on many models; do not open the lid in a spin unless the manual allows
Twin tub Wash tub and spin tub side by side Drain hose and lint filter; balance the load in the spin tub

Your manual names the exact filter and its position.

Load and dose

  • Do not overload the drum and do not overdose detergent. Too much soap leaves residue and smells; too many clothes strain the machine and wash badly.
  • Empty pockets (coins, hairpins, keys), close zips and use a wash bag for small items. Coins and pins are the usual cause of a blocked filter.
  • Use the detergent type the manual names (many front loaders need a low-foam or "HE" detergent).
  • For laundry as a business (stain removal, care symbols, pricing), see the hub's Laundry and Cleaning Services course.

After every wash

  1. Leave the door and the detergent drawer slightly open so air can move and mould does not grow.
  2. On a front loader, wipe the door seal and check its folds for coins and fluff.
  3. Switch off and unplug if you will not use it again that day.

Monthly and two-monthly care

Clean the drain pump filter (front loader)

Follow your manual. These steps follow two makers' guides.

  1. Unplug the machine. If you just ran a hot wash, wait for the water to cool.
  2. Put a towel on the floor and a shallow bowl in front of the small door at the bottom front.
  3. Open the small door. If there is a small emergency drain hose, pull it out, hold it over the bowl, remove its cap and let the water run out. Empty the bowl as needed. Cap the hose and push it back.
  4. Turn the filter anticlockwise and pull it out slowly (more water may come).
  5. Remove fluff, coins, hair and pins. Rinse the filter in warm water. Wipe the hole it came from with a damp cloth.
  6. Refit the filter clockwise until it is tight, so it does not leak.
  7. Close the small door. Plug in. Run a short rinse and check for drips at the filter.
  8. Record the date and what you found.

Electrolux suggests cleaning the drain pump filter every two months, or when the machine shows a drain error.

Clean the detergent drawer and run a maintenance wash

  1. Pull out the detergent drawer (press the release tab shown in the manual).
  2. Wash it in warm water only; brush away soap and mould; brush the drawer hole too.
  3. Refit the drawer. Run an empty rinse.
  4. Once a month, run the empty maintenance or drum-clean programme, or the hottest cotton cycle the manual allows, with nothing in the drum.
  5. Wipe the outside with mild soap and water; never use solvents or scouring pads.

Hoses and position

  • Inlet hoses carry water at pressure. Check them for bulges, cracks, kinks and leaks. Makers advise replacing inlet hoses about every 5 years, or sooner if they bulge or leak.
  • The drain hose must not be squashed or pushed too deep into the drain pipe; follow the manual for height.
  • Level: a machine that is not level vibrates and "walks" in the spin. If it moves, report it; Level 2 teaches levelling.
  • Transit bolts: a new front loader has bolts in the back to hold the drum during transport. They must be removed before first use. If a new machine shakes violently, ask whether the bolts were removed.

Find the cause

For each, say the most likely user cause and the user fix. (1) The front loader smells bad. (2) It stops with water inside and a drain error. (3) Grey marks of soap on dark clothes. (4) A new machine jumps across the floor in the first spin.

Pocket patrol

For one week, check every pocket before washing at home. Keep in a small box everything you find. Count it.

Check yourself

  1. Name two things you do after every wash on a front loader.
  2. Which way do you turn the filter to remove it?
  3. How often do makers suggest replacing inlet hoses?
05

Unit 4 · Gas cookers and the LPG cylinder

Gas is a good friend when used properly and a bad friend when it is not. Keep the cylinder outside, the hose sound, and your nose alert.

Competency standard

Learning outcome Performance criteria — the trainee…
4.1 Place the cylinder safely keeps the cylinder upright, outside or in an airy space, away from heat
4.2 Check hose and regulator inspects the hose and regulator; knows when to replace
4.3 Test for leaks the safe way does the soapy-water test; never uses a flame
4.4 Light and use the cooker safely lights correctly; keeps pots, cloths and children safe
4.5 Clean burners cleans caps and ports as the maker says
4.6 Act on a gas smell follows the gas-smell steps

Range. Two- and four-burner table-top cookers, free-standing cookers with an oven, domestic LPG cylinders. Evidence. Observed leak test (outdoors, trainer present); burner clean; gas-smell role-play.

Ask a qualified expert. Gas can explode. For any leak you cannot stop by closing the cylinder valve, a damaged cylinder, or a cooker that will not light properly, keep the gas off and call an authorised LPG dealer, a trained gas technician, or 112 in an emergency. This unit teaches user safety, not gas fitting.

Where the cylinder lives

  • Not in a closed room. The NPA tells users to store cylinders in well-ventilated areas or secure outdoor cages. Leaking gas cannot be seen, so a cylinder in a closed kitchen lets gas build up where a spark can light it.
  • Upright, on firm level ground, in a ventilated place or a secure outdoor cage. Transport it upright in a ventilated vehicle.
  • Away from open flames and flammable liquids such as petrol and kerosene.
  • Do not ask for a cylinder to be filled to the brim: it needs room to expand.

The Cylinder Recirculation Model (CRM). Under CRM, consumers exchange cylinders at exchange points, and the NPA says these points will verify cylinder weights so consumers get the full value of what they pay for. Ask your nearest LPG outlet whether CRM exchange is available in your town (not verified for the Western Region).

Hose and regulator

  • Inspect the hose often. Replace it at once if it is cracked, hard, perished, sticky or chewed by rats, and at the interval the maker or your authorised dealer gives. An official Ghana replacement interval was not found (not verified: ask the NPA or the Ghana National Fire Service).
  • Use clips or fittings made for gas hoses; never tie with rubber or wire.
  • Never put a stone or heavy object on a regulator to stop a leak. The NPA says it does not work, is dangerous and has caused fires; replace faulty hoses, valves or rubber O-rings with certified parts from authorised LPG dealers.
  • Check the cylinder's expiry or test date; old cylinders must be recertified or replaced.

The soapy-water leak test

Soapy-water test (outdoors, trainer present)

These steps follow Energy Safe Victoria, an Australian gas safety regulator.

  1. Mix dish soap and water in a spray bottle or cup.
  2. Make sure all cooker knobs are off. Open the cylinder valve.
  3. Spray or brush the soapy water on the cylinder valve, the regulator joint, both ends of the hose and along the hose.
  4. Watch for bubbles that grow. Bubbles mean gas is escaping.
  5. If bubbles appear: close the cylinder valve; check the hose; tighten the joint by hand; check the rubber O-ring; test again. If bubbles still form, keep the gas off and get the part replaced by an authorised dealer.
  6. Wipe off the soap. Record the test.
  7. Do this every time you connect a cylinder, and whenever you suspect a leak.

Never use a match, lighter or torch to look for a leak.

Lighting and using the cooker

  1. Check knobs are off. Open the cylinder valve slowly.
  2. Light the burner the way the cooker's manual says (spark lighter or match).
  3. If it does not light within a few seconds, turn the knob off, wait for the gas to clear, then try again.
  4. Keep the flame under the pot; turn pot handles inwards; keep cloths and curtains away; never leave cooking alone; keep children back.
  5. After cooking, turn off the knob and close the cylinder valve.

Clean the burners

Burner clean

These steps follow a cooker maker's guide.

  1. Knobs off; cylinder valve closed; cooker cool.
  2. Lift off the burner caps and bases. Scrub with a non-scratch plastic pad and mild cleaner.
  3. Clear blocked holes (ports) with a straight pin or needle. Do not use a wooden toothpick: it can break off inside. Do not make the holes bigger.
  4. Do not use oven cleaner or bleach.
  5. Dry completely. Refit each cap on its own base so it sits flat.
  6. Open the valve; light each burner; the flame should be blue and even. A yellow, lazy or noisy flame after cleaning is for a gas technician.

If you smell gas

Gas smell: act at once.

  1. Do not operate any electrical switch or device, and do not use a phone near the leak: a spark can ignite the gas.
  2. Put out all flames. Do not smoke or strike a match.
  3. Turn off the gas at the cylinder, but only if it is safe to do so.
  4. Open doors and windows; keep people away from the area.
  5. Get everyone out. From a safe place, call 112 if the smell stays or there is a fire.
  6. Do not use the cooker again until the leak is found and fixed.

The hub's Home Fire and Gas Safety course teaches fire extinguishers, escape plans and fire prevention in more depth.

Spot the danger

A chop bar keeps its cylinder lying on its side under the cooking table, next to a gallon of kerosene. The regulator hisses, so a stone sits on it. List every danger and the right action for each.

Gas check at home

With an adult, check your home's cylinder: where is it, is it upright, how old is the hose, what date is on the cylinder? Write what you would change.

Check yourself

  1. Where should the cylinder be kept?
  2. What do bubbles mean in the soapy-water test?
  3. Why must you not switch on a light when you smell gas?
06

Unit 5 · Microwaves, fans, irons, kettles and water dispensers

Small appliances are cheap to buy and easy to ruin. Five minutes of care a week keeps them safe.

Competency standard

Learning outcome Performance criteria — the trainee…
5.1 Use and clean a microwave uses safe containers; cleans inside; spots door damage
5.2 Clean a fan unplugs, removes the grille and blades, cleans and refits
5.3 Care for an iron uses the right water; empties, cools and stores it safely; descales as the manual says
5.4 Care for a kettle empties, wipes and descales as the manual says
5.5 Clean a water dispenser switches off, unplugs, drains, cleans and rinses

Range. Countertop microwave, table and pedestal fans, steam and dry irons, electric kettle, hot-and-cold water dispenser. Evidence. Observed fan clean and dispenser clean; microwave check; oral questions.

Ask a qualified expert. Never open a microwave or remove its cover: it holds deadly voltage even when unplugged. Never open a fan motor, iron or kettle. For any fault, use a trained appliance technician. For burns or shock, see a doctor or nurse; call 112 in an emergency.

Microwave oven

The US Food and Drug Administration (FDA) gives this advice:

  • Do not use it if the door does not close firmly or is bent, warped or damaged; if hinges, latches or seals are damaged, contact the maker or a qualified repairer.
  • Stop using it at once if it keeps running when the door is open.
  • Use containers made for microwaves. No metal pans or aluminium foil. Do not use plastic that can melt.
  • Water can superheat (get hotter than boiling without bubbling) and then erupt when moved; do not heat liquids longer than the manual says.
  • Some ovens must not be run empty: follow the manual.

Clean a microwave

  1. Unplug it.
  2. Put a microwave-safe bowl of water with a slice of lemon or a spoon of vinegar inside; plug in and heat as the manual allows for a few minutes so steam softens the dirt; unplug again. (Watch: do not superheat; leave the bowl to stand before lifting it.)
  3. Wipe inside, the turntable and the door seal area with a soft cloth. Wash the turntable in soapy water.
  4. Check the door: does it close firmly? Any cracks, bent edges or damaged hinges? Report any damage; do not use it.
  5. Never poke anything into the vents or holes.

Fans

Clean a pedestal or table fan

These steps follow a maker's guide. Follow your manual for the grille clips or screws.

  1. Unplug and wait for the blades to stop.
  2. Remove the front grille (clips or a small screw), the blade cap and the blades. Keep the screws in a cup.
  3. Wash the grilles and blades in warm water with mild soap; dry fully.
  4. Wipe the motor body with a dry or barely damp cloth. Never wet the motor.
  5. Refit in the reverse order. Check the blades spin freely by hand before plugging in.
  6. A fan that hums but does not turn, runs very slowly or smells hot: unplug and call a technician (do not "help" it by spinning the blades while it is on).

Irons

  • Unplug the iron and let it cool before you fill, empty, clean or descale it.
  • Use the water type the manual says. Some makers recommend distilled or demineralised water, or a mix with tap water, to cut scale; never use perfumed water unless the manual allows.
  • Philips advises descaling every one to two months, or when the calc light shows, using the iron's own self-clean or calc-clean function.
  • Empty the water tank after use; store the iron standing on its heel, cool, with the cord loosely wrapped.
  • Never leave a hot iron face down or within reach of children.

Kettles

  • Fill between the minimum and maximum marks; never switch on empty.
  • Unplug, then empty after use; wipe the outside with a damp cloth; never put the base in water.
  • Scale (white crust) wastes power; descale as the manual says. Electric kettles are covered by Ghana's energy-efficiency labelling rules.

Water dispensers

Clean a hot-and-cold water dispenser

These steps follow a maker's guide. Your manual comes first.

  1. Switch off the hot and cold switches at the back; unplug; remove the bottle.
  2. Let the hot tank cool before draining (hot water burns).
  3. Drain the remaining water through the taps (and any drain plug the manual shows) into a bucket.
  4. Pour in a cleaning solution the manual allows (some makers allow white vinegar with water). Let it stand about 15 minutes; run it out through both taps.
  5. Rinse with clean water several times until there is no taste or smell left.
  6. Wipe the taps, drip tray and bottle seat. Wash the drip tray.
  7. Fit a new clean bottle; let water run through both taps; plug in; switch on cold, then hot.
  8. Record the date.

What would you do?

(1) The microwave door is cracked but "it still works". (2) The iron spits brown water. (3) The dispenser water tastes of vinegar after cleaning. (4) The fan grille is broken and a child's finger fits through.

Small appliance survey

In your home, check the microwave door, the fan grille and the iron cord. Write one care action for each.

Check yourself

  1. Give two FDA reasons to stop using a microwave.
  2. What must you never do to a fan motor while cleaning?
  3. Why let a dispenser's hot tank cool before draining?
07

Unit 6 · Power cuts, surges, voltage guards and energy labels

The light goes off, the light comes back, and the fridge dies. Learn to protect your appliances, and learn to read the energy label before you buy.

Competency standard

Learning outcome Performance criteria — the trainee…
6.1 Act in a power cut switches off sensitive appliances and waits before switching back on
6.2 Use voltage guards and surge protection chooses the right device and plugs it correctly
6.3 Read the energy label reads the stars, energy use and QR code on the Energy Commission label
6.4 Work out running cost calculates kWh and cost per month for an appliance
6.5 Know when to call a technician decides user fix or technician from a symptom

Range. Fridge, freezer, TV, washing machine, iron, kettle, fans; prepaid and postpaid meters. Evidence. Label-reading exercise; running-cost calculations; guard demonstration; oral questions.

Ask a qualified expert. For frequent voltage problems, a socket that sparks, or any work on the meter, wiring or breakers, call the electricity company or a licensed electrician (a Certified Electrical Wiring Professional). Do not open the meter or the breaker board.

When the power goes off and comes back

  1. Switch off and unplug sensitive appliances (TV, decoder, computer, microwave, washing machine) when the power goes.
  2. Leave one bulb switched on so you know when power returns.
  3. Wait a few minutes after power returns before switching appliances back on. Power can come back with brief surges or spikes that damage appliances, which is why emergency agencies advise unplugging during an outage.
  4. During low voltage (dim lights, fans running slowly), switch off appliances. ECG's official advice on low voltage was not found on an ECG page (not verified: ask your ECG district office).
  5. Switch on the big appliances one at a time, not all at once.

Voltage guards and surge protectors

Device What it does Use it for
Voltage guard (fridge guard, AC guard, TV guard) Cuts power when the voltage is too low or too high, and waits a set time before reconnecting Fridges, freezers, ACs, TVs
Surge-protected extension board Absorbs short voltage spikes TV, decoder, computer, phone chargers
Ordinary extension board Only extra sockets; may give little or no surge protection Light loads only

A voltage guard cuts the power when the voltage goes outside a set window and waits a set time before reconnecting; the window and the delay differ by model and are printed on the maker's leaflet. The delay protects a fridge's compressor from fast on-off switching. For fridges and freezers, choose a guard made for fridges, with a restart delay, rated for the appliance's current, from a trusted shop.

Fit a plug-in guard

  1. Read the guard's leaflet: voltage window, delay, maximum amps or watts.
  2. Check the appliance's plate: is the appliance within the guard's rating?
  3. Unplug the appliance. Plug the guard into the wall socket; plug the appliance into the guard.
  4. Watch the lights: the guard should show "waiting" (delay), then "on".
  5. Never plug a guard into a loose extension board chain; never plug a high-power iron or kettle through a fridge guard.
  6. Write on the record card: guard type, date fitted.

The Energy Commission label

Ghana has a mandatory standards and labelling scheme. Makers, importers and retailers of regulated appliances must sell only appliances that meet minimum energy-efficiency standards, are labelled and are registered with the Energy Commission.

  • Regulated appliances include fridges and freezers, washing machines, microwave ovens, electric kettles, rice cookers, comfort fans and ventilating fans, TVs, storage water heaters, air conditioners and LED lamps.
  • The label uses stars from 1 to 7: more stars means more efficient than other models of similar size and features.
  • The label shows figures such as volume, capacity and energy consumption, and carries a QR code created after the model is approved and entered in the Commission's product database.
  • The Commission inspects appliances in shops and, with the Ghana Standards Authority, tests samples.

Read the label

  1. Visit an electrical shop (or use the trainer's photo set).
  2. For two fridges of similar size, write: stars, energy use (kWh a year or a day as printed), volume.
  3. Scan the QR code with a phone and note what it shows.
  4. Say which fridge would cost less to run, and why.

Running cost

kWh = watts × hours ÷ 1,000. Cost = kWh × the price per kWh.

From 1 July 2026 the Public Utilities Regulatory Commission (PURC) set residential electricity at 203.7509 pesewas per kWh for the first 300 kWh in a month and 269.2235 pesewas above 300 kWh; a "lifeline" rate of 89.9315 pesewas applies to homes using only 0 to 30 kWh; there is also a monthly service charge. PURC reviews tariffs every quarter, so check the current rate before you calculate (a later review was not found; not verified). Taxes and levies on the bill are not included here.

Worked example (appliance figures are example; rate from PURC, rounded to GH¢2.04 a kWh). A fridge uses 1.2 kWh a day. In 30 days: 1.2 × 30 = 36 kWh. Cost: 36 × 2.04 = GH¢73.44 a month.

What does it cost?

Use GH¢2.04 per kWh (PURC 0–300 band from 1 July 2026, rounded). All appliance figures are example. (a) A 1,000 W iron used 3 hours a week for 4 weeks. (b) A 60 W fan used 10 hours a day for 30 days. (c) A 2,000 W kettle used 15 minutes a day for 30 days. (d) Which costs most a month?

User fix or technician?

Symptom User checks If still wrong
Appliance dead Is the socket on? Is the guard in its delay? Try a lamp in the same socket Technician (or electrician if the socket is dead)
Fridge warm Seal, dial, air space, coils, overloading (Unit 2) Refrigeration technician
Washer will not drain Clean the filter (Unit 3) Appliance technician
Cooker flame yellow Clean burners (Unit 4) Gas technician or authorised dealer
Burning smell, sparks, shock None: switch off and unplug Technician at once

Your meter

Read your home's prepaid or postpaid meter at the same time on two days. Work out the kWh used in one day and its cost.

Check yourself

  1. Why wait before switching on after power returns?
  2. What do more stars mean on the Energy Commission label?
  3. A 100 W TV runs 5 hours a day for 30 days. How many kWh?
08

Unit 7 · Your location, small business ideas and marketing yourself

Many homes, hostels and shops have appliances but nobody who cares for them. Start small, be honest about your limits, and refer repairs to trained technicians.

Competency standard

Learning outcome Performance criteria — the trainee…
7.1 Choose honest services lists care services within the user's limits
7.2 Cost and price costs a care kit and prices a visit
7.3 Choose a location names places with many appliances and few care services
7.4 Market yourself honestly writes a profile that does not claim repair skills

Range. The trainee's own plan. Evidence. Kit costing; one-page plan; profile.

Ask a qualified expert. Do not sell repair, wiring or gas fitting at this level. Refer those jobs to trained technicians and licensed electricians. Before you register a business or sign a contract, ask the Assembly, the GRA or a qualified lawyer; this is general information, not legal advice.

Small business ideas (honest ones)

  • Fridge and freezer care visits: inside clean, seal check, coil dusting, defrost (manual models), thermometer check, for homes, chop bars and cold-store shops
  • Washing machine care visits: filter and drawer clean, seal wipe, maintenance wash, hose check
  • Fan and dispenser cleaning for offices, schools, churches and hostels
  • Gas safety checks for users: soapy-water test, hose age check, moving cylinders outside (no gas fitting)
  • Power-protection help: selling and plugging in voltage guards and surge-protected boards from trusted suppliers
  • Shopping help: going with a buyer to read the energy label and check the receipt and warranty

Never call yourself a "repairer" or "technician" at this level. Keep a list of trained technicians and licensed electricians you trust, and refer jobs to them. If you earn a referral fee, tell the customer.

Location settings that give good returns

  • Hostels and student areas near Takoradi Technical University and colleges, where many fridges, irons and fans are shared
  • Guesthouses and homestays along the coast (Busua, Dixcove, Akwidaa), where appliances run with salt air and power cuts
  • Chop bars, cold-store and drinks shops at Market Circle and town markets, where a dead freezer means lost stock
  • Estates and compounds in Anaji, Kwesimintsim and Effia, where working families have washing machines
  • Schools, churches and offices with dispensers and fans

Cost and price

Cost a care kit (all figures are example)

You buy: a soft brush GH¢15; 3 microfibre cloths at GH¢10 each; a plastic bowl GH¢10; mild dish soap GH¢20; white vinegar GH¢25; a small torch GH¢40; 2 old towels at GH¢25 each; a tool bag GH¢60. (a) What does the kit cost? (b) You charge GH¢80 for a washing-machine care visit; soap and transport cost GH¢30 a visit. What is the profit per visit? (c) How many visits pay back the kit? (d) Profit from 12 visits in a month?

Market yourself honestly

  • WhatsApp Business: a business profile with your name, area and services, with greeting and away messages. Post before-and-after photos (with the owner's permission).
  • Google Business Profile: a free listing so people searching nearby can find you.
  • Signage and cards: "Appliance care and cleaning · Fridges, washing machines, fans, dispensers · Repairs referred to trained technicians".
  • Referrals: landlords, caretakers, hostel managers, market queens, church groups and electrical shops.
  • Your portfolio: your hub certificate, record cards of jobs done (no customers' private details), photos, written thanks from customers.

Accessibility

Ghana's Persons with Disability Act, 2006 (Act 715) bans discrimination against persons with disabilities at work and requires public places and services to be accessible. Ask your Assembly's social welfare office about the Assemblies' disability fund and what it supports (the current share was not verified on an official page).

Much of this work suits persons with disabilities: cleaning fans, dispensers, microwaves and fridge shelves at a table; label reading and shopping help; record keeping; selling guards. Adjustments that help: a work table at wheelchair height and a helper or trolley for moving heavy appliances; large-print or audio checklists and tactile marks on cleaning bottles for people with low vision; picture job cards and WhatsApp text bookings for deaf workers; working in pairs on site. Ask the person what works for them.

My plan

  1. Choose two services from the list.
  2. Cost your kit and price one visit.
  3. Choose a location and explain why.
  4. Write a one-page plan: your name, services, customers, prices, and the jobs you will refer.
  5. List three technicians or electricians you could refer to (ask at the hub).

Ask three customers

Ask a hostel manager, a shop owner and a parent what appliance problems they have and what they would pay for a care visit.

Check yourself

  1. Name two honest appliance-care services at Level 1.
  2. What must your sign or profile never claim?
  3. Name two adjustments for a worker who uses a wheelchair.
09

Glossary

Term Meaning
Competent / Not Yet Competent The two possible results of a CBT assessment
Rating plate The label giving the appliance's volts, hertz, watts and model
Watt (W) How fast an appliance uses power
kWh Kilowatt-hour: 1,000 watts for one hour; what the meter counts
Condenser coils The black pipes at the back or bottom of a fridge that give out heat
Door seal (gasket) The rubber strip that closes the fridge or front-loader door
Drain pump filter The trap at the bottom front of a front loader that catches fluff and coins
Transit bolts Bolts that hold a new washing machine's drum during transport
Regulator The part on an LPG cylinder that lowers the gas pressure for the cooker
CRM Cylinder Recirculation Model: exchange an empty cylinder for a filled, checked one
Superheated water Water heated past boiling without bubbling, which can erupt
Descaling Removing the white mineral crust from an iron or kettle
Voltage guard A device that cuts power when voltage is too high or too low
Surge protector A device that absorbs short voltage spikes
Energy label The Energy Commission label with stars, energy use and QR code
CEWP Certified Electrical Wiring Professional, licensed by the Energy Commission
10

Logbook

Copy these pages into an exercise book. Your logbook is part of your assessment evidence.

  • Unit 1: rating-plate exercise; plug and cord check; three record cards
  • Unit 2: fridge clean; seal check; one-week temperature log
  • Unit 3: filter clean; drawer clean; maintenance wash record
  • Unit 4: soapy-water test record; burner clean; gas-smell role-play
  • Unit 5: microwave check; fan clean; dispenser clean
  • Unit 6: guard fitted; label reading; running-cost calculations; meter readings
  • Unit 7: kit costing; one-page plan; referral list
  • Every homework, dated
11

Self-check quiz

  1. What is Ghana's mains voltage and frequency?
  2. Why should high-power appliances go straight into a wall socket?
  3. What temperature should a fridge keep?
  4. Why must you leave space behind a fridge?
  5. What should you check for in a front loader's door seal?
  6. Which way does the drain pump filter usually turn out?
  7. Where should an LPG cylinder be kept?
  8. What must you never put on a leaking regulator?
  9. Name one FDA reason to stop using a microwave.
  10. Why wait after power returns before switching on?
  11. What do more stars on the Energy Commission label mean?
  12. A 1,500 W iron runs 2 hours. How many kWh?
12

Further reading and sources

Best next reads: your own appliances' manuals; the Energy Commission's guidance on energy labels; the NPA's LPG safety messages; Home Appliance Care Level 2.

What this module does not cover: repair of any appliance; refrigerant work; electrical wiring; gas fitting; air conditioners (see the hub's Refrigeration and Air-Conditioning Basics course); generators (see Appliance, TV and Generator Repair); fire fighting and escape plans (see Home Fire and Gas Safety).

Every source used in this manual is listed, with links, in the Teacher Copy.

One application of the Cold-Start Learning Kit, which stays general-purpose and can build a guide on any topic in any field. Written in CTVET format; not a CTVET curriculum.