About this module
At Level 1 you made a pad and a handle from plain bar. At Level 2 the parts must go together: a screw must turn in a nut, a shaft must slide in a bush. That is the difference between turning metal and making a machine part.
Who it is for. Trainees who have completed Level 1 (or can show equal skill), aged 18 or over. National Proficiency II leads on from NP I; holders work with some independence on routine and some varied tasks. Nobody under 18 may do hazardous work in Ghana.
CTVET status. This is not a CTVET curriculum. Ask CTVET or the regional Ghana TVET Service office for the official Welding and Fabrication or Machining standard and match this module to it.
Bridge from Level 1: what you already know
- You follow the lathe safety protocol every time (no gloves, key out, guard in place, stop before clearing swarf).
- You can name all 15 parts of the lathe and set speed from the formula RPM = 1000 × m/min ÷ (π × mm).
- You mount work, set the tool at centre height and measure with a caliper and micrometer.
- You can face, turn, centre drill, drill and part off, and you made the clamp pad and handle.
- You know ISO 2768 general tolerances and can write a process sheet.
How the module works
Each unit has learning outcomes, performance criteria, a range and evidence. Every unit has a Tools and items table, every new machine has a labelled diagram with a parts table, and every machine or hazardous task has a SAFETY PROTOCOL box. The back of the book has quick cards, fault charts, a mistake catalogue, blank forms and an index.
Standards. International standards (ISO, OSHA and so on) are used where Ghana has no standard we could find; they are labelled "international". Check numbers against the Ghana Standards Authority text when you can read it. International values are not Ghana law.
Unit 1 · Machine safety at the next level
The new machines bring new hazards: a drill that grabs the work, a cutter that spins faster than you can see, a thread that does not stop where you expect. Add these rules to your Level 1 rules.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 1.1 Repeat the Level 1 rules | follows the lathe safety protocol without prompting |
| 1.2 Use the drilling machine safely | clamps the work, removes the chuck key, never holds work by hand |
| 1.3 Use taps, dies and files safely | holds work in a vice and uses taps correctly |
| 1.4 Isolate and lock out | isolates and locks the machine before any repair or belt change |
| 1.5 Handle lifts | uses two people or a lifting aid for chucks, vices and heavy bar |
Range. Lathe, drilling machine, bench grinder, hand tools; the mill and shaper by demonstration. Evidence. Observation every session; oral questions; daily check sheets.
Ask a qualified expert. For electrical, mechanical, lifting or other dangerous work, use a licensed electrician, a qualified safety officer or a GhIE-registered engineer. Do not attempt work you are not trained and authorised to do. For any injury, illness or medicine, see a doctor or nurse. This unit teaches awareness and good practice, not medical treatment.
The law again, and what machines have in common
Ghana's Factories, Offices and Shops Act 1970 (Act 328) requires that dangerous machines are used only by people who are instructed and trained or supervised (section 36), that dangerous parts are fenced (section 38) and the fencing kept in place (section 40), and that set-screws, bolts and keys are sunk or guarded (section 41). OSHA 1910.212, an international (USA) rule, lists the machines that normally need point-of-operation guarding, including milling machines and power saws; fixed machines must be anchored. Whether your workshop is a "factory" that must register is a question for the Department of Factories Inspectorate.
New hazards at a glance
| Machine or task | Main hazard | The rule |
|---|---|---|
| Drilling machine | Work grabs and spins; chuck key thrown | Clamp the work or hold it in a vice; remove the key; use a drill speed that suits the size |
| Thread cutting on the lathe | The carriage runs on automatically; a crash at the shoulder | Rehearse with the machine off; know where to stop; keep one hand on the stop |
| Tapping and die work | Broken tap; cuts from sharp threads | Hold work in a vice; use cutting oil; never force |
| Milling | Cutter spins with great force | Never reach over the cutter; chip guards; no gloves |
| Shaper | Moving ram strikes; flying chips | Keep clear of the ram path; set the stroke before starting |
| Steady rest and long work | Whipping bar | Support long work; guard bar ends; slow speed |
| Knurling | The knurl tool pulls in the work | Use slow speed and plenty of oil |
Drilling machine: parts and safety
Photo credit: Niklitov, CC BY-SA 4.0. Cropped, resized and numbered for this manual.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Motor | Drives the spindle (through belts or gears in the head) | Isolate it before any work inside the head |
| 2 | Head | Houses the drive gears or pulleys and the speed levers | Never open it while the machine is connected |
| 3 | Feed handles | Lower the spindle by hand | Use steady pressure; ease off as the drill breaks through |
| 4 | Spindle and quill | The shaft that turns and slides down to feed the drill | Do not touch it while it turns |
| 5 | Column | The upright pillar that carries the head and table | Do not hang tools on it |
| 6 | Table (slotted) | Carries the work or vice; the slots take clamp bolts | Clamp the work; never hold it by hand |
| 7 | Base | The heavy foot that carries the whole machine | Keep the floor around it clear |
This machine is larger than a bench drill and is shown without a drill or guard fitted. Your own machine will have a different shape and must have its guards in place.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Base | The heavy foot that carries the machine | Bolt it down; keep clear of clutter |
| 2 | Column | The upright pillar that carries the head and table | Do not hang tools on it |
| 3 | Head | Houses the spindle, bearings and the drive pulleys | Isolate before opening |
| 4 | Motor | Drives the spindle through belts | Keep belt guard closed; lock out for belt changes |
| 5 | Spindle and quill | The shaft that rotates and slides down to feed the drill | Do not touch while it turns |
| 6 | Chuck and drill | The chuck grips the drill bit | Remove the chuck key every time |
| 7 | Table | The platform that holds the work or vice | Clamp work to it |
| 8 | Feed lever | Lowers the spindle by hand | Use steady pressure; ease off as the drill breaks through |
| 9 | Work clamp or vice | Holds the work so it cannot spin | Never hold the work by hand |
| 10 | Table lock | Locks the height and swing of the table | Lock before drilling |
| 11 | Belt guard | Covers the belts and pulleys | Never run with it open |
SAFETY PROTOCOL: Drilling machine
Before you start
- Glasses on, no gloves, no loose sleeves or jewellery, hair tied back.
- Work clamped in a vice or to the table; table locked; drill tight in the chuck; chuck key removed; belt guard closed.
- Speed set for the drill size (Unit 3 table). Isolator located.
While you work
- Do: centre punch first; start the hole slowly; ease the feed as the drill breaks through; withdraw to clear swarf; use cutting oil on steel.
- Do not: hold the work by hand; wear gloves; clear swarf with your fingers; stop the spindle with your hand; leave the machine running.
After you finish
- Switch off and wait for the spindle to stop. Isolate. Brush the table clean (never blow). Remove the drill and put it away. Report a bent drill or faulty belt guard.
Emergency
- Stop and isolate. If a hand is trapped, do not pull: switch off first and get help. Call 112 for a serious injury. Control bleeding with a clean cloth pressed firmly; see a doctor or nurse.
Tools and items for Unit 1
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Machine vice | A vice that bolts to the drill table and holds work | 100 mm jaws | Drill vice |
| G-clamp | A C-shaped clamp for holding work to a table | 100 to 150 mm | C-clamp |
| Tap wrench | Handle that turns a tap | T-handle | Tap handle |
| Die stock | Handle that holds a die | 25 mm | Die holder |
| Padlock and hasp (lockout) | Lock for the isolator so nobody switches it on | Lock-out lock | |
| Danger tag | A tag saying "Do not use" or "Machine under repair" | Warning tag | |
| Safety glasses | Eye protection | Safety goggles |
Safety refresh
- Repeat the Level 1 walk-round at the lathe, and at the drilling machine.
- Show how to clamp a bar to the drill table.
- Practise a lockout on a machine that is switched off: isolator off, padlock on, tag on, try the start button to prove it is dead.
- Explain two hazards and rules for each machine in the table.
Near-miss log
For one week, write down every safety slip or near miss you see in the workshop (no names), what rule it broke and how to prevent it.
Check yourself
- What do you do before changing a belt on a drill?
- Why must work be clamped, not held in the hand, when drilling?
- What is the first thing to do if someone is trapped?
Unit 2 · Threading and tapers
A screw is a ramp wrapped round a rod. A taper is a cone with a slope. Both look simple on paper and need care on the machine.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 2.1 Describe the metric thread | gives the thread form, pitch and depth for a common size |
| 2.2 Cut an external thread | cuts an M12 × 1.75 thread on the lathe to fit a nut |
| 2.3 Use taps and dies | taps an internal thread and cuts an external one by die |
| 2.4 Turn a taper | sets the compound rest or the tailstock to turn a taper and checks it |
| 2.5 Calculate | works out half-angle, set-over, thread depth and tap drill |
Range. M6 to M16 coarse threads; Morse taper and short tapers. Evidence. A fitted thread; a measured taper; calculation sheet.
Ask a qualified expert. Threads in lifting gear, pressure parts or vehicle parts are the work of a qualified engineer or mechanic: ask a GhIE-registered engineer or a qualified mechanic before you make or sell such a part. Do not make load-bearing parts without an engineer's design.
The ISO metric thread
The ISO metric thread has a 60 degree angle between its flanks. The height of the sharp triangle is H = 0.866 × pitch P. The thread depth is 0.54125 × P, and the minor diameter is the major diameter minus 1.0825 × P. Coarse pitches are M6: 1, M8: 1.25, M10: 1.5, M12: 1.75, M16: 2, M20: 2.5 mm. Check against the ISO 261 and ISO 262 text and the Ghana Standards Authority edition when you can read them.
Thread data table (calculated by script from the formulas).
| Thread | Pitch P (mm) | Thread depth (mm) | Minor diameter (mm) | Tap drill from chart (mm) | Compound infeed at 29.5 degrees (mm) |
|---|---|---|---|---|---|
| M6 | 1.00 | 0.541 | 4.918 | 5.0 | 0.62 |
| M8 | 1.25 | 0.677 | 6.647 | 6.8 | 0.78 |
| M10 | 1.50 | 0.812 | 8.376 | 8.5 | 0.93 |
| M12 | 1.75 | 0.947 | 10.106 | 10.2 | 1.09 |
| M16 | 2.00 | 1.083 | 13.835 | 14.0 | 1.24 |
| M20 | 2.50 | 1.353 | 17.294 | 17.5 (rule: major minus pitch) | 1.56 |
Tap drills are the usual chart values; the rule "major diameter minus pitch" gives a good estimate. Charts differ slightly: check the tap maker's chart. The last column is the compound-rest travel for a tool set at 29.5 degrees (a common workshop practice, not from a standard): depth ÷ cos 29.5 degrees.
Cutting an external thread on the lathe
The lead screw drives the carriage a fixed distance per turn of the spindle. The half-nut lever on the apron locks the carriage to the lead screw. You choose the pitch from the gear chart (or set change gears: ratio = thread pitch ÷ lead screw pitch; for a 6 mm lead screw and 1.75 mm thread, 1.75 ÷ 6 = 0.2917, which the chart gives in gears). Use a low speed (about 100 rev/min for a first thread).
Cut an M12 × 1.75 thread
- Turn a bar to 12 mm diameter (minus 0.1 mm), with a 1 mm chamfer and a relief groove at the end of the thread so the tool can run out (a shallow groove about 3 mm wide, to the minor diameter).
- Fit a 60 degree thread tool, set exactly at centre height and square to the work (use a thread gauge or centre gauge).
- Set the gearbox for 1.75 mm pitch and a low speed.
- Touch the tool to the work, set the cross-slide dial to zero, and note the compound dial.
- Engage the half-nut at the right mark and make a light first pass. Stop; check the pitch with the screw pitch gauge.
- Withdraw the tool with the cross-slide, disengage or reverse the carriage to the start, then return the cross-slide to zero and feed the compound by 0.1 to 0.2 mm each pass. Depth total about 0.95 mm, so about 8 to 10 passes, with lighter cuts at the end.
- Test with a nut (or a ring gauge) after the last pass. A good fit turns by hand without play.
- Remove the key and keep one hand on the stop at every pass.
SAFETY PROTOCOL: Screw cutting on the lathe
Before
- Standard lathe protocol (glasses, no gloves, key out, guard on). Rehearse each pass with the machine off, winding the carriage by hand to the end of the thread.
- Set a run-out groove. Mark the stop position. Set a low speed.
While
- Do: keep one hand on the stop; keep eyes on the tool and the end of the thread; disengage the half-nut before the tool reaches the shoulder; withdraw the tool by the same amount each time.
- Do not: leave the half-nut engaged near the chuck; chat; run a thread against a shoulder with no relief; touch the lead screw.
After
- Stop and isolate. Check the thread, clean with a brush (not by hand), oil the work to stop rust. Report any chipped tool.
Emergency
- Crash: press stop and isolate, check for injury and machine damage. Report. Do not restart until the instructor has checked it.
Taps and dies
A tap cuts an internal thread in a drilled hole; a die cuts an external thread on a rod. Drill the right tap drill, hold the work firmly, start the tap square, turn forward half a turn and back a quarter turn to break the swarf, use cutting oil, and finish with a second or third tap if you have a set (taper, second, plug). Never force a tap: a broken tap is very hard to remove.
Tapers
A taper is a cone. The half-angle is atan((D − d) ÷ (2 × L)), where D is the large diameter, d the small and L the taper length. Example (checked by script): D = 30, d = 24, L = 60: half-angle = atan(6 ÷ 120) = 2.862 degrees. To turn it with the compound rest, swivel it to that half-angle (the diagram) and feed the compound by hand: it suits short tapers.
For long gentle tapers you can set over the tailstock: offset = L_total × (D − d) ÷ (2 × l), where L_total is the full length of the work between centres and l the length of the taper. Example: 200 mm between centres, taper from 30 to 24 mm over 60 mm: offset = 200 × 6 ÷ 120 = 10 mm. (This is a geometric calculation; check by trial.) Where the lathe has a taper attachment, set the angle on its scale.
Morse tapers are the standard self-holding tapers on drill chucks, centres and tailstock barrels. Taper per mm and sizes:
| MT size | Taper (µm per mm) | Taper ratio (1 in …) | Half-angle (degrees) | Large end diameter (mm) |
|---|---|---|---|---|
| 0 | 52.051 | 19.21 | 1.491 | 9.045 |
| 1 | 49.882 | 20.05 | 1.429 | 12.065 |
| 2 | 49.951 | 20.02 | 1.431 | 17.780 |
| 3 | 50.196 | 19.92 | 1.438 | 23.825 |
| 4 | 51.938 | 19.25 | 1.488 | 31.267 |
(The ratio and half-angle columns are worked from the taper values by script.) A small lathe often has MT2 and a 300 to 400 mm swing machine MT3; check the plate on your machine. Keep tapers clean, because dirt and burrs stop them seating.
Tools and items for Unit 2
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| 60 degree thread tool | Tool ground to the thread angle for external threads | HSS, 8 to 10 mm | Screw-cutting tool |
| Thread (centre) gauge | A small flat gauge to set the thread tool square | 60 degrees | Centre gauge, fishtail gauge |
| Screw pitch gauge | A set of blades that match thread pitches | Metric 0.4 to 6 mm | Thread gauge |
| Thread dial indicator | A dial on the apron showing where to engage the half-nut | Thread chasing dial | |
| Half-nut lever | Locks the carriage to the lead screw | ||
| Tap set (taper, second, plug) | Taps that cut an internal thread in three stages | M6 to M12 | Thread taps |
| Tap wrench | Handle for turning taps | ||
| Die and die stock | Cuts external threads by hand | M6 to M12 | Thread die |
| Ring gauge or thread nut | Checks external threads | Go gauge | |
| Taper attachment | A bar that guides the cross-slide to turn tapers | ||
| Morse taper sleeve | Reduces a large taper to a smaller one | MT1 to MT3 | Morse sleeve |
| Dial indicator and magnetic base | Checks run-out and taper | 0.01 mm | Dial gauge |
Thread and taper calculations
(a) Work out the thread depth and minor diameter for M10 × 1.5. (b) A bar 250 mm long between centres is turned with a taper from 25 mm to 22 mm over 100 mm. The tailstock offset? (c) The compound angle for a taper from 40 to 32 mm over 80 mm?
Thread card
Make a pocket card with pitch, depth, minor diameter and tap drill for M6 to M16 from the table, and check one value by calculation.
Check yourself
- What is the angle between the flanks of the metric thread?
- What lever locks the carriage to the lead screw?
- Why use a run-out groove?
Unit 3 · Boring, knurling, drilling and holes
A hole is half of every fit. A drilled hole is rough. A bored or reamed hole is true. Choose the process for the accuracy you need.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 3.1 Choose the hole process | picks drill, bore or ream for the accuracy needed |
| 3.2 Bore a hole | bores a hole to a size on the lathe |
| 3.3 Ream a hole | reams a drilled hole to a size |
| 3.4 Knurl a surface | knurls a handle with a good pattern |
| 3.5 Set drilling speeds | sets the drilling machine speed from a table |
Range. Holes 6 to 40 mm; mild steel and brass. Evidence. A bored and reamed bush measured; a knurled handle.
Ask a qualified expert. A bushing or housing used in vehicles, lifting or pressure equipment must have an engineer's design: ask a GhIE-registered engineer or a qualified mechanic. For any cut, burn or eye injury, see a doctor or nurse.
Which process?
| Process | Typical accuracy | Use |
|---|---|---|
| Twist drill | Rough; hole often 0.1 to 0.3 mm oversize | Clearance holes, starting a bore |
| Boring on the lathe | Good; to a few hundredths of a millimetre | Exact diameter, true to the axis, larger holes |
| Reaming | Very good size and finish (hole size about H7, check the maker) | Fit holes for pins and bushes |
| Tapping | Thread | Internal threads |
Boring (step by step)
A boring bar holds a small cutting tip on a bar that enters the hole. It is thinner than the hole so it springs more than a turning tool: keep the overhang short, take light cuts and the tool is set at centre height, with cutting edge pointing away from the chuck face. Boring bars cut best when the bar is as thick and short as possible.
Bore a bush to size
- Mount the work true in the chuck. Face the end. Centre drill and drill a hole smaller than the final size (about 2 to 3 mm smaller).
- Fit the boring bar with as little overhang as the hole depth needs; set at centre height.
- Use a speed about 20 to 30 percent lower than turning the same diameter because of the bar's flexibility (a beginner rule; check the instructor's chart).
- Take a trial cut 5 mm deep, stop, measure the bore with an inside caliper (or telescopic gauge), and set the cross-slide.
- Rough to 0.2 mm under size and finish with a light cut at a fine feed.
- Chamfer the mouth and deburr.
Reaming
A reamer is a multi-edge tool that follows a drilled hole and trims it to size. Drill about 0.2 to 0.5 mm under the reamer size for small holes (see the maker's guide), run the reamer slowly with plenty of oil, and never turn a reamer backwards (it dulls the edges).
Knurling
A knurling tool presses a pattern of ridges into the work to give a grip, for example on a handle. It uses wheels called knurls (straight, diamond), a slow speed and plenty of oil, and pressure applied slowly. Example (checked by script): a 25 mm diameter with a 1 mm pitch gives about 78.5 teeth round the circumference. The diameter grows slightly: turn a little under size to allow.
Drilling machine speeds
At 25 m/min (low-middle for HSS in mild steel), the speed for each drill diameter is RPM = 1000 × 25 ÷ (π × D). Brass tolerates higher speeds. Table (calculated):
| Drill diameter (mm) | Mild steel 20 m/min | Mild steel 25 m/min | Brass 100 m/min | Aluminium 150 m/min |
|---|---|---|---|---|
| 6 | 1,061 | 1,326 | 5,305 | 7,958 |
| 8 | 796 | 995 | 3,979 | 5,968 |
| 10 | 637 | 796 | 3,183 | 4,775 |
| 12 | 531 | 663 | 2,653 | 3,979 |
| 16 | 398 | 497 | 1,989 | 2,984 |
| 20 | 318 | 398 | 1,592 | 2,387 |
| 25 | 255 | 318 | 1,273 | 1,910 |
| 32 | 199 | 249 | 995 | 1,492 |
Table values are calculated by script. If your machine cannot reach the speed, use the highest below it. A drill that is too fast burns; too slow wastes time.
Tap drill sizes (chart values, Source: HPA Tapping Guide): M6 5.0; M8 6.8; M10 8.5; M12 10.2; M16 14.0 mm. A tap drill leaves about 75 percent of a full thread.
Tools and items for Unit 3
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Boring bar | A bar that carries a small cutting tip into a hole | 10 to 20 mm | |
| Reamer, hand and machine | A multi-edge tool that finishes a hole to size | 6 to 20 mm | |
| Knurling tool | A holder with hardened wheels that press a pattern | Knurl | |
| Inside caliper or telescopic gauge | Transfers hole size to a micrometer | ||
| Inside micrometer or bore gauge | Measures a bore | 6 to 50 mm | |
| Drill set (twist drills) | Drills in graduated sizes | 1 to 13 mm | Drill bits |
| Counterbore and countersink | Tools that make a flat-bottomed or conical recess for screw heads | ||
| Cutting oil | Coolant and lubricant |
Bore, ream and knurl
- Make a mild steel bush: drill 16 mm, bore to 18 mm, drill a second bush at 11.8 mm and ream it to 12 mm (check the reamer maker's guide).
- Knurl a 25 mm brass handle with a diamond pattern.
- Set the drilling machine speeds for five hole sizes from the table.
- Measure the bored hole three ways and compare.
Hole sizes
(a) The drill and speed for an M10 tapped hole in mild steel? (b) Speed for a 16 mm drill in brass at 100 m/min? (c) Number of knurl teeth around a 20 mm diameter at 1 mm pitch?
Hole process chart
Draw a chart showing which process you would use for: a hole for an M8 bolt, a bush bore to a precise size, a fit hole for a pin. Say why.
Check yourself
- Why must a reamer never be turned backwards?
- Which is more accurate: drilling or boring?
- What does a tap drill leave?
Unit 4 · Milling, shaping and other machines
The lathe turns round work. The mill and shaper make flat faces, slots and steps. Know what each machine does best, even if you do not own one.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 4.1 Name the parts | names the parts of a vertical mill and a shaper |
| 4.2 Say what each does | states what milling and shaping are best for |
| 4.3 Plan a simple setup | describes how to hold and cut a flat face |
| 4.4 Work safely | states the hazards and protocol for each machine |
Range. Demonstration and supervised use. Evidence. Labelling test; a planned flat face.
Ask a qualified expert. A milling machine and a shaper are dangerous. Use them only after training and with supervision. Ask a licensed electrician about power and a GhIE-registered engineer about installation. Ghana's Act 328 requires dangerous machines to be run by trained or supervised people.
The vertical milling machine
A mill spins a multi-edge cutter while the work, clamped on a table, moves under it. The table moves in X and Y; the knee raises the table; the quill or head moves the cutter down. Vertical mills hold the cutter in the spindle; the knee carries the saddle and table.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Base | Heavy foot carrying the column | Bolt down |
| 2 | Column | Upright with dovetail ways for the knee | Do not hang tools on it |
| 3 | Knee | Carries the saddle and table; raises and lowers | Lock before cutting |
| 4 | Saddle | Slides on the knee; gives the cross travel | Lock the axis not in use |
| 5 | Table | Holds the work with tee slots | Clamp work firmly |
| 6 | Head | Carries the spindle and motor | Never open while running |
| 7 | Spindle and quill | The rotating shaft that holds the cutter; the quill feeds down | Do not touch while turning |
| 8 | Vice | Clamps the work to the table | Tighten and check before cutting |
| 9 | Table handwheel | Moves the table by hand | Turn with the machine off to set |
| 10 | Quill feed lever | Feeds the cutter down | Use steady pressure |
| 11 | Cutter (end mill) | The multi-edge tool that cuts | Keep sharp; never touch the teeth |
| 12 | Motor | Drives the spindle | Isolate before maintenance |
Speed and feed for milling. RPM = 1000 × cutting speed ÷ (π × cutter diameter). Table feed rate = RPM × number of teeth × chip load per tooth. Example: a 10 mm four-flute HSS end mill in mild steel at 20 m/min: RPM = 637; with 0.03 mm per tooth, feed = 637 × 4 × 0.03 = 76 mm/min (checked by script; the chip load is an example: check the cutter maker's chart).
SAFETY PROTOCOL: Milling machine
Before
- Glasses on; no gloves; hair tied; sleeves buttoned. Work clamped; cutter tight; guards and chip shield in place; table locks set; hand-turn the axes to check clearance; isolator known.
While
- Do: stop the spindle to measure, change work or clear chips; use a brush or hook; cut against the feed direction rules the instructor teaches (climb or conventional); keep clear of the cutter.
- Do not: reach over or near a spinning cutter; wear gloves; use a rag; leave the key in the drawbar or chuck; touch chips with your hand.
After
- Switch off; wait for the cutter to stop. Isolate. Clean chips with a brush. Remove and store the cutter. Report faults.
Emergency
- Press stop, isolate, help the injured, call 112 for serious injury. Stop bleeding with a clean cloth pressed firmly and see a doctor or nurse.
The shaper
A shaper cuts flat faces, slots and steps with a single-point tool carried on a ram that moves back and forth. The table moves across at each stroke. It is slower than a mill but cheap and good for flat faces and keyways in a small shop.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Base | The heavy foot | Bolt down |
| 2 | Column | The housing for the drive | Keep covers closed |
| 3 | Ram | The sliding arm that carries the tool back and forth | Keep out of its path; set the stroke before starting |
| 4 | Tool head | Carries the tool and sets the depth | Lock before cutting |
| 5 | Tool and clapper box | The cutting tool; the clapper box lets the tool lift on the return stroke | Tight; short overhang |
| 6 | Table | Holds the work | Clamp firmly |
| 7 | Cross rail and saddle | Move the table across and up | Lock before cutting |
| 8 | Vice | Clamps the work | Check tightness |
| 9 | Stroke adjusting wheel | Changes the length of the stroke | Adjust with the machine stopped |
SAFETY PROTOCOL: Shaper
Before
- Glasses on; no gloves; hair tied. Work clamped; stroke set; hand-wheel the ram through a full stroke to check clearance; chip guard in place; isolator known.
While
- Do: stand to the side, clear of the ram's end; stop to measure or clear chips.
- Do not: stand behind the ram or in front of the table end; reach over the work; adjust the stroke while running.
After
- Switch off and isolate; clean with a brush; retract the ram; store tools.
Emergency
- Stop and isolate; help the injured; call 112 for serious injury; see a doctor or nurse for any wound.
What each machine is best at
| Machine | Best for | Not good for |
|---|---|---|
| Lathe | Round work: shafts, bushes, threads, tapers | Flat faces on big work |
| Drilling machine | Holes | Accurate bores |
| Milling machine | Flat faces, slots, steps, keyways, gears | Long thin round work |
| Shaper | Flat faces and keyways in a small shop; cheap | Long production runs |
| Bench grinder | Sharpening tools | Precise sizing |
| Power hacksaw or chop saw | Cutting bar to length (see Basic Welding for the saw rules) |
Tools and items for Unit 4
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| End mill | A multi-edge cutter for slots and faces | 6 to 20 mm | Slot drill |
| Face mill | A wide cutter for flat faces | 50 to 80 mm | Fly cutter |
| Machine vice | Holds work on the table | ||
| Parallels | Hardened strips that raise the work in the vice | ||
| Edge finder | A tool that finds the edge of the work | ||
| Tee bolts and clamps | Hold work to the tee slots | ||
| Chip guard | A clear shield |
Plan a flat face
- Identify the 12 parts of the mill from the diagram.
- With the instructor, set up a block in a vice on parallels and make a light facing cut.
- Describe the setup in writing: cutter, speed, feed, depth of cut.
- Explain why the shaper may suit a small shop for keyways.
Machine comparison
Make a one-page comparison of lathe, mill and shaper: what each does, a cost class (low, medium, high) and where you might find one in Ghana (Suame Machine Tools members use lathes, milling machines and drilling machines).
Check yourself
- Which machine moves the work under the cutter?
- What is the clapper box for?
- Where must you not stand beside a shaper?
Unit 5 · Patterns, templates, tolerances and fits
Before you cut metal, you need a pattern to follow. After you cut, you need a limit to say the part is good. This unit covers both.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 5.1 Make a template | makes a template from a drawing and uses it to mark and check |
| 5.2 Plan a casting pattern | applies shrinkage and machining allowance to a pattern size |
| 5.3 Read limits and fits | explains clearance, transition and interference fits |
| 5.4 Choose a fit | chooses a fit for a shaft and hole |
| 5.5 Gauge parts | uses limit gauges or pins to accept or reject |
Range. Templates in hardboard or thin sheet; simple patterns; fits for shafts 10 to 50 mm. Evidence. Template, pattern allowance sheet, fit calculation.
Ask a qualified expert. Fits and tolerances for parts in vehicles, lifts or pressure equipment must be set by a qualified engineer. Ask a GhIE-registered engineer. International standards are quoted here; check against the Ghana Standards Authority text.
A template and a pattern
A template is a full-size cut-out of the part, in hardboard, sheet steel or aluminium, used to mark out, to check a shape or to guide a cut. A pattern is a copy of the part, a little bigger, used to make the mould for a casting. An example from Suame: the Intermediate Technology Transfer Unit at KNUST ran an iron foundry at Suame Magazine, so patterns and castings are part of Ghana's machine-shop history.
Pattern allowances (international rules of thumb, check with your foundry). Metal shrinks as it cools, so the pattern is made bigger: about 1 percent for cast iron, 1.3 to 1.6 percent for aluminium, about 1.3 to 1.5 percent for brass, about 2 percent for steel; add 1.5 to 2.5 mm of machining allowance on each face that will be machined; and add a draft (taper) of about 1 to 3 degrees on the pattern's sides so it comes out of the sand. Sources differ slightly: ask the foundry for its figures.
Worked example (checked by script). A finished aluminium block must be 200 mm between two machined faces. Add 2 mm on each machined face: 204 mm. Aluminium shrinkage 1.5 percent: pattern length = 204 × 1.015 = 207.06 mm.
Limits and fits
A fit describes how a shaft sits in a hole. ISO 286 is the international system. A clearance fit leaves a gap (the shaft turns or slides), an interference fit has a hole smaller than the shaft (pressed together), and a transition fit may be either. The letters: capital for the hole (H), small for the shaft (g, h, k, p…); the number after is the tolerance grade (IT). Common choices: H7/g6 close sliding or running; H7/h6 locational clearance; H7/k6 and H7/n6 transition; H7/p6 locational interference, pressed.
Worked example: 40 mm H7/g6 (international). Using IT7 = 25 µm and IT6 = 16 µm for 40 mm, and the g6 upper deviation of −9 µm:
- Hole H7: 40.000 to 40.025 mm.
- Shaft g6: 39.991 to 39.975 mm.
- Minimum clearance = 40.000 − 39.991 = 0.009 mm; maximum clearance = 40.025 − 39.975 = 0.050 mm (matches the published range, Source: JLC Fits).
- For H7/h6: shaft 40.000 to 39.984 mm; clearance from 0 to 0.041 mm.
Note: for ISO 286 values for other sizes, use the ISO tables or a trusted calculator. This course gives only the 40 mm worked example. Check against the ISO 286 and Ghana Standards Authority text.
Choosing a fit (guide).
| Use | Fit |
|---|---|
| Rotating shaft in a bush, light load | H7/g6 or H8/f7 |
| Parts to be assembled by hand and located accurately | H7/h6 |
| Parts to be located exactly and pressed or lightly tapped | H7/k6 or H7/n6 |
| Parts pressed permanently together | H7/p6 (check the table for small sizes) |
| Loose clearance, no precision | H11/c11 or a general tolerance |
For small diameters H7/p6 may behave as a transition fit, so check the tables.
Gauging
A go / no-go gauge is a fast check. The "go" end must enter the hole and the "no-go" must not. A plug gauge checks holes; a ring gauge or snap gauge checks shafts. Use gauge pins and a micrometer when you do not have the gauges.
Tools and items for Unit 5
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Hardboard or thin sheet | Material for templates | 3 to 6 mm | |
| Scriber and dividers | Marking tools | Compasses | |
| Plug gauge (go, no-go) | Checks a hole size | Pin gauge | |
| Gauge pin set | Hardened pins of known size | Pin gauges | |
| Snap gauge | Checks a shaft size | Gap gauge | |
| Surface plate | Flat reference table | ||
| Height gauge | Measures and marks heights | 300 mm | |
| Micrometer | Precise measuring |
Fits and patterns
(a) A 40 mm shaft is h6 in an H7 hole. What are the largest and smallest clearances? (b) An iron casting is 150 mm after machining, one machined face on each end, with 2 mm machining allowance each; the pattern allowance is 1 percent. Find the pattern length. (c) Why is H7/p6 checked carefully for small sizes?
Make a template and a fit
- Make a hardboard template of the clamp frame's shape (Level 3 will build the frame).
- Calculate the pattern size for an aluminium handle boss.
- Turn a shaft 12 mm and bore a bush to make a close running fit: measure both and write the clearance.
- Use pins to gauge the bush.
Fit table
Look up two fits in a library or on a reputable site, write the limits for a 25 mm shaft, and compare with your measured parts. Label foreign values international.
Check yourself
- What is a clearance fit?
- Why is a pattern bigger than the finished part?
- What does a no-go gauge do?
Unit 6 · Getting the best from each machine
A machine that is well set up, sharp and cared for makes better parts, lasts longer and costs less to run. This unit is about getting the best from every machine.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 6.1 Choose speed and feed | picks speed and feed for a material and tool |
| 6.2 Get a good finish | uses tool, speed, feed and coolant to improve surface finish |
| 6.3 Extend tool life | recognises wear and sharpens or replaces tools |
| 6.4 Set up the machine | checks alignment, rigidity and workholding |
| 6.5 Maintain the machine | follows a maintenance schedule |
Range. Lathe, drilling machine, mill (observed). Evidence. A speed and feed sheet; a maintenance log; a fault diagnosis.
Ask a qualified expert. Electrical problems (voltage dips, tripping, wiring) must be handled by an Energy Commission-certified electrician; serious repair or realignment of a machine by a qualified machinist; foundations and anchoring by a GhIE-registered engineer. For any injury, see a doctor or nurse.
Speed and feed: the five factors
Good cutting depends on cutting speed, feed, depth of cut, tool material and coolant. For plain HSS tools, with one-hour tool life and dry cutting, surface speeds are about 3 to 38 m/min for mild steel, 90 to 210 for brass and 122 to 305 for aluminium, with medium-grade cast iron far lower. Carbide tools run much faster: one catalogue example for medium-carbon steel is 150 m/min at 0.12 mm/rev and 1.0 mm depth, wet. Use the insert maker's chart for real starting values.
Spindle speeds table (calculated by script). Rev/min for cutting speeds at common diameters.
| Diameter (mm) | 15 m/min (cast iron, HSS) | 25 m/min (mild steel, HSS) | 100 m/min (brass, HSS) | 150 m/min (aluminium, HSS or carbide steel) |
|---|---|---|---|---|
| 10 | 477 | 796 | 3,183 | 4,775 |
| 20 | 239 | 398 | 1,592 | 2,387 |
| 30 | 159 | 265 | 1,061 | 1,592 |
| 40 | 119 | 199 | 796 | 1,194 |
| 50 | 95 | 159 | 637 | 955 |
(Cutting speeds from the ranges in Wiki Speeds Feeds; rev/min values worked from RPM = 1000 × Vc ÷ (π × D).) Your lathe may not have all speeds: use the nearest lower one.
Getting a good finish
- A sharp tool with a small nose radius for finishing cuts (a slightly larger radius gives a better finish at low feeds).
- A fine finishing feed (0.05 to 0.1 mm/rev).
- Correct speed: too slow gives a torn surface on steel; too fast burns the tool.
- Cutting oil on steel; dry or light oil on brass; a free-cutting approach on aluminium.
- A rigid set-up: short work overhang, tight tool post, locked carriage.
- A last light cut (0.1 mm) and a quick wipe with fine emery cloth on the work when the machine is stopped or held safely as the instructor shows, never wrapped round the work.
Tool life
A tool is worn when it leaves a rough finish, squeals, makes the work oversize, or shows a bright worn edge. Resharpen before it is badly blunt: it takes less grinding. Do not overheat when grinding; quench often. Keep a tool log: tool, material cut, time or parts made, wear seen.
Set-up and alignment checks
Test the machine
- Tailstock alignment. Turn a trial bar between centres or with one end chucked and measure the diameter at both ends of a short section with a micrometer. If they differ, the tailstock is off line: adjust the set-over screws and repeat. A bar turned parallel means the tailstock is aligned.
- Run-out of the chuck. Mount a bar, put a dial indicator on it and rotate by hand. Note the total reading. Large run-out means a worn or dirty chuck or a bent bar.
- Slack. Check the cross-slide and compound for backlash (dial turned back leaves a gap). Always approach the final size from the same direction.
- Spindle noise. Run empty for two minutes at each speed and listen for rumble or squeal.
Maintenance schedule
| When | Do |
|---|---|
| Every day | Wipe and oil slideways; check guards and stop; check oil sights; clear swarf |
| Every week | Clean the lead screw and feed rod; check belt tension; check chuck and jaws for swarf; oil moving parts |
| Every month | Check gib screws on slides; inspect electrical leads (ask an electrician); check coolant, replace if smelly |
| Every year | Level the machine; check the spindle; replace worn belts; service with a qualified machinist |
Use only the oils and greases the maker names; keep a log. Ghana power note: voltage dips and cuts can damage motors; ask an Energy Commission-certified electrician about a voltage protector and correct cable size.
Fault-finding chart: the machine
| Fault | Likely cause | Fix |
|---|---|---|
| Chatter | Overhang; loose gib; blunt tool; speed | Shorten; adjust gibs; sharpen; change speed |
| Taper | Tailstock off line; worn bed | Re-align; check wear |
| Rough finish | Blunt tool; feed too high | Sharpen; reduce feed |
| Work moves in the chuck | Jaws worn or not tight | Retighten; check jaws; use soft jaws |
| Thread wrong pitch | Wrong gear setting | Check chart and pitch gauge |
| Drill wanders | No centre punch or centre drill | Use one |
| Hole oversize | Drill sharpened unevenly | Resharpen drill; start with a smaller drill and ream |
| Motor trips | Overload, bad wiring | Lighter cut; ask an electrician |
Tools and items for Unit 6
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Dial indicator on a magnetic base | Shows run-out and alignment | 0.01 mm | Dial gauge |
| Test bar | A ground bar for testing alignment | 150 mm | |
| Gib key | A taper strip that adjusts slide tightness | ||
| Grease gun | Puts grease into nipples | ||
| Oil (way oil, spindle oil) | Lubricant named by the maker | ||
| Tool log | A notebook for tool wear |
Plan the machine
(a) Spindle speed for a 40 mm brass bar at 100 m/min? (b) Spindle speed for a 50 mm mild steel bar at 25 m/min? (c) A trial bar measures 30.00 mm at the chuck end and 30.06 mm at the tailstock end. Which way is the tailstock off, and what should you do?
Maintenance log
Make a maintenance log with the schedule above and keep it for one week on the workshop machine, signing each entry.
Check yourself
- Name two ways to get a smoother finish.
- Why sharpen a tool early?
- What does a bar that is bigger at the tailstock end tell you?
Unit 7 · Assemble several parts; location and business
The screw, the nut, the pad and the handle are good parts. A clamp is the parts working together. Assembly is where fit, finish and checking pay off.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 7.1 Make the screw and nut | makes an M12 × 1.75 screw and a matching nut |
| 7.2 Assemble parts | assembles the screw, nut, pad and handle into a working sub-assembly |
| 7.3 Check the fit | checks fits and function and records them |
| 7.4 Quote the work | works out a machine-hour cost and a batch price |
| 7.5 Plan a location and market | names location features and a marketing plan |
Range. The clamp sub-assembly (screw, nut, pad, handle). Evidence. The sub-assembly; fit record; quote.
Ask a qualified expert. This is general information, not legal, tax or financial advice. Ask a qualified lawyer about contracts and registration, GRA or a qualified accountant about tax, and your bank about loans. A clamp is not a lifting device: do not sell a clamp, screw or nut as a lifting or load-bearing part; ask a GhIE-registered engineer for any design where failure could hurt someone.
The screw and nut
The screw is a 12 mm mild steel rod with an M12 × 1.75 thread about 100 mm long, a turned head to take the handle cross-hole (6 mm hole) and a turned ball or flat end to take the pad. The nut (the frame's threaded boss) has an M12 × 1.75 thread tapped at 10.2 mm drill.
| Part | Material | Key sizes |
|---|---|---|
| Screw | Mild steel Ø12 bar | M12 × 1.75, 100 mm thread, Ø10 spigot 8 mm for the pad |
| Nut (boss) | Mild steel Ø30 bar, 25 mm thick | Drill 10.2, tap M12 × 1.75 (or bore and thread) |
| Pad | Mild steel Ø18 (from Level 1) | 6 mm hole to fit the Ø6 pin |
| Handle | Mild steel Ø8 × 120 mm | Fits a Ø8 H7 cross-hole in the screw head (Level 3 frame) |
Assembly rules
- Check each part against the drawing and the inspection sheet before assembly.
- Deburr every edge; clean every part; oil threads.
- Assemble in the order on the process sheet; fit by hand first, tools last.
- If a fit is tight, find which part is wrong: do not force it.
- Record the assembly check and take a photo for your portfolio.
Fit check
The screw must turn in the nut by hand with a small amount of play; the handle must slide in the cross-hole; the pad must seat without rocking. Record each fit: part, size, fit result.
A batch price (examples)
Machine-hour cost example from Level 1: GH¢30.42 per hour. A set of screw, nut, pad and handle takes (example) 1.5 hours of machine time. Material cost per set (example) GH¢28. Cost per set = 1.5 × 30.42 + 28 = GH¢73.63 (45.63 + 28 = 73.63). For 10 sets: cost GH¢736.30 (example). With a 30 percent mark-up the price is 736.30 × 1.3 = GH¢957.19 (profit GH¢220.89). Remember: mark-up is profit ÷ cost and margin is profit ÷ price (here 23.1 percent). All numbers are examples.
Location and business ideas
- Near vehicle and farm machinery repair; bar suppliers; welders and fabricators who need turned parts.
- Offer a repair service (rebuild threads, bushes and shafts), small batches of fasteners and clamps, and a training service.
- Keep a portfolio, a WhatsApp Business catalogue, a Google Business Profile and signage.
Basic Welding Level 3 explains subcontracting machining to Suame Magazine or Kokompe; at your own shop you can win that work yourself. The Assembly permit, ORC business name (GH¢130 in 2026) and the tax number are covered in Level 1 Unit 7 and Level 3 Unit 6.
Accessibility
The Persons with Disability Act 2006 bans job discrimination. Process planning, quoting, inspection and drawing are desk work suitable for many wheelchair users. Machine work needs a safe seated workstation or an adjustable bench; deaf workers need visual signals; blind workers should not operate machines. Ask a qualified occupational therapist or safety officer about adjustments.
Make and assemble
- Make the M12 screw and nut to the drawing; check the thread.
- Check all four parts against the inspection sheet and assemble.
- Record the fits and photograph the sub-assembly.
- Work out a quote for 10 sets.
Price a batch
Use GH¢30.42 per machine hour, 1.5 hours and GH¢28 material per set. (a) Cost per set. (b) Price of 10 sets at a 30 percent mark-up. (c) The margin as a percent of the price.
Portfolio page
Photograph the parts and the assembly. Make a portfolio page with sizes and a one-line description of each part.
Check yourself
- Why must you fit the parts by hand first?
- What is the difference between margin and mark-up?
- Is a screw clamp a lifting device?
Appendix A · Tools and Items Glossary
Note on names. Local names for machines and tools differ from town to town, and many have none. Use the standard name in this book and show the picture or the tool when you ask for it. The "Also called" column gives other common English or trade names.
| Item | What it is and what it does | Typical size or type | Also called |
|---|---|---|---|
| Boring bar | Carries a small cutting tip into a hole | 10 to 20 mm | |
| Chip guard | Shield against flying chips | ||
| Compound rest | Swivelling slide used for short tapers and thread infeed | ||
| Counterbore | Cutter that makes a flat-bottomed recess | ||
| Die and die stock | Cuts an external thread | M6 to M12 | |
| Dial indicator | Shows small movements to 0.01 mm | Dial gauge | |
| End mill | Cutter for slots and faces | 6 to 20 mm | |
| Gauge pins | Hardened pins of exact size | ||
| Gib | Taper strip that sets slide tightness | ||
| Half-nut | Locks the carriage to the lead screw | ||
| Knurling tool | Presses a grip pattern | ||
| Machine vice | Holds work on a drill or mill table | ||
| Morse taper | Standard self-holding taper | MT1 to MT4 | |
| Plug gauge | Go / no-go gauge for holes | ||
| Reamer | Finishes a hole to size | ||
| Screw pitch gauge | Matches thread pitch | Thread gauge | |
| Tap | Cuts an internal thread | M6 to M16 | |
| Tap wrench | Turns a tap | ||
| Taper attachment | Guides the cross-slide for tapers | ||
| Thread dial | Shows where to engage the half-nut | ||
| Thread tool | 60 degree tool for external threads |
Appendix B · Quick cards
Card 1: formulas
- RPM = 1000 × m/min ÷ (π × mm).
- Thread depth = 0.54125 × P; minor diameter = major − 1.0825 × P.
- Half-angle = atan((D − d) ÷ (2L)).
- Tailstock offset = L_total × (D − d) ÷ (2 × l).
- Pattern size = (finished size + machining allowance) × (1 + shrinkage).
Card 2: before a thread
- Low speed. Run-out groove. Tool at centre height, square. Rehearse with the machine off. Hand on the stop.
Appendix C · Mistake catalogue (Level 2)
- Cutting a thread at too high a speed.
- Forgetting the run-out groove.
- Forcing a tap and breaking it.
- Turning a reamer backwards.
- Using a worn boring bar with long overhang.
- Using tailstock set-over without testing a trial cut.
- Not clamping work on the drilling machine.
- Mixing up mark-up and margin.
Appendix D · Blank forms
Thread record. Date ____ Thread ____ Pitch ____ Depth ____ Passes ____ Gauge result ____ Fit record. Parts ____ Shaft size ____ Hole size ____ Clearance ____ Fit class ____ Maintenance log. Date ____ Machine ____ Task ____ Done by ____ Fault noted ____
Appendix E · Index
Boring: Unit 3. Clearance fit: Unit 5. Compound rest: Unit 2. Drilling machine: Unit 1. Fit: Unit 5. Knurling: Unit 3. Lockout: Unit 1. Maintenance: Unit 6. Milling: Unit 4. Morse taper: Unit 2. Pattern allowance: Unit 5. Reamer: Unit 3. Shaper: Unit 4. Tap drill: Unit 2, 3. Taper: Unit 2. Thread: Unit 2.
Glossary
| Term | Meaning |
|---|---|
| Clearance fit | A fit with a gap between shaft and hole |
| Competent / Not Yet Competent | The two possible results of a CBT assessment |
| Draft | The slope on a pattern so it leaves the mould |
| Fit | How a shaft and hole go together |
| Interference fit | A fit where the shaft is larger than the hole |
| Lead screw | Threaded rod that drives the carriage |
| Pitch | Distance between thread crests |
| Taper | A cone-shaped surface |
| Template | A cut-out used to mark or check a shape |
| Tolerance | Allowed variation in a size |
Logbook
Copy these pages into an exercise book. Your logbook is part of your assessment evidence.
- Unit 1: safety refresh; lockout practice
- Unit 2: thread card; thread record; taper calculations
- Unit 3: bored and reamed bush; knurled handle
- Unit 4: machine comparison; flat face plan
- Unit 5: template; pattern allowance; fit record
- Unit 6: speed sheet; maintenance log; test bar results
- Unit 7: screw and nut; assembly record; quote
- Every homework, dated
Self-check quiz
- What is the angle of a metric thread?
- Give the thread depth for a 1.5 mm pitch.
- What lever locks the carriage to the lead screw?
- Why use a run-out groove?
- How do you calculate the half-angle of a taper?
- Why not turn a reamer backwards?
- Name two ways to get a good finish.
- Name the three kinds of fit.
- What does H7/g6 describe?
- Why is a pattern bigger than the finished casting?
- Name one thing you must never do near a milling cutter.
- Define mark-up and margin.
Further reading and sources
Best next reads: your machines' manuals; the thread and fit tables of a machinery handbook; this course's Level 3; the Hub's Basic Welding and Fabrication.
What this module does not cover: CNC machining, jigs and fixtures, drawing and inspection systems (Level 3); welding (see Basic Welding and Fabrication); ISO 286 values beyond the 40 mm worked example (use the standard); Ghana machine and bar prices (all prices are examples).
Every source used in this manual is listed, with links, in the Teacher Copy.