About this module
A lathe turns a piece of bar so fast that it feels nothing, and it cuts steel as easily as a knife cuts yam. That is why it is so useful and so dangerous. This module teaches you to respect it, understand every part of it, and make accurate parts that fit together.
Who it is for. People with no formal certificate, aged 18 or over. National Proficiency I is a bridging level; holders do routine tasks under supervision. In Ghana, nobody under 18 may do hazardous work.
How this fits with other Hub courses
Do not repeat what other manuals teach. General shop safety, hand tools, welding and the shop business for a welder are in the Hub's Basic Welding and Fabrication (Levels 1 to 3). This course teaches the machine shop: the lathe, the drilling machine, measuring, fits, making parts, and putting parts together into a piece of work. Where a machined part is welded or bevelled, Basic Welding Level 2 covers the welding. When a job is too big for your machines, Basic Welding Level 3 explains how to subcontract machining at Suame Magazine or Kokompe; this course shows you how to do some of that work yourself.
The running project: a screw bench clamp
Across the three levels you make one real piece of work, a screw bench clamp (like a small G-clamp). In this book you make the pad and the handle. In Level 2 you make the screw and nut and learn fits. In Level 3 you make the frame and jig, assemble everything, inspect it and present it.
Why the lathe
- Suame Magazine in Kumasi has a Machine Tools Cooperative whose members run lathes, milling machines and drilling machines to make bolts, nuts, gears and shafts.
- KNUST's Intermediate Technology Transfer Unit moved capstan lathes, milling and gear-hobbing machines to Suame artisans in the 1980s, and a 2025 project trained artisans in CAD, foundry and machine-shop work.
- Apprenticeship pays off most for people with the least schooling; see the Hub's Basic Welding and Fabrication for the studies.
CTVET and GhIE. Ghana has competency-based training in welding and fabrication; the official unit list for machine-shop work was not found online, so this module is not that curriculum. Ask CTVET or the regional Ghana TVET Service office. For artisan licensing, ask the Ghana Institution of Engineers (GhIE).
How the module works
Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent by being watched at work, by your parts, by answering questions and by your logbook.
Every unit has a Tools and items table (every tool is named and defined where you first meet it), every machine has a labelled diagram with numbered parts and a parts table (part, what it does, safety rule), and every machine or hazardous task has a SAFETY PROTOCOL box: before, while, after, emergency. At the back are quick cards, a fault chart, a mistake catalogue, blank forms and an index.
Standards used. Ghana has no published lathe or machine-shop standard that we found. Where a number comes from an international standard (ISO, OSHA and so on), it is labelled international and you must check it against the Ghana Standards Authority text when you can read it. International values are never Ghana law.
Unit 1 · Work safely at the lathe
A lathe does not hurt anyone on purpose. It simply keeps turning. A sleeve, a glove, a hair tie or a chuck key can be pulled in faster than you can move. Every rule in this unit exists because someone was hurt.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 1.1 Dress for the lathe | wears close-fitting clothes, safety glasses and boots; no gloves, rings, watches, necklaces or loose sleeves; hair tied back |
| 1.2 Control entanglement | never leaves the chuck key in; never reaches over a turning chuck; never holds emery cloth by hand on turning work |
| 1.3 Control swarf | stops the machine before clearing swarf; uses a hook and brush, never bare hands |
| 1.4 Use guards and stops | keeps the chuck guard in place and knows where the stop button and isolator are |
| 1.5 Handle loads | lifts chucks and heavy bar with help or a lifting aid |
| 1.6 Act in an emergency | stops the machine, isolates power, calls for help (112) and gives first aid |
Range. All machine-shop work. Evidence. Observation every session; oral questions; completed daily check sheet.
Ask a qualified expert. For electrical, mechanical, lifting or other dangerous work, use a licensed electrician, a qualified safety officer or a GhIE-registered engineer. Do not attempt work you are not trained and authorised to do. For any injury, illness or medicine, see a doctor or nurse. This unit teaches awareness and good practice, not medical treatment.
The law and the guards
- Ghana's Factories, Offices and Shops Act 1970 (Act 328) requires dangerous machines to be operated only by people who are instructed and trained or supervised (section 36), dangerous moving parts to be fenced (section 38), fencing to be soundly built and kept in place while parts move (section 40), and set-screws, bolts and keys to be sunk or guarded (section 41).
- It also requires safe access and clear space at machines (section 34) and a first-aid box (section 28).
- International practice (OSHA 1910.212, a USA rule, not Ghana law): guard against rotating parts, flying chips and sparks; fixed machines must be anchored so they cannot walk.
- Whether your small workshop counts as a "factory" that must be registered is not settled here: ask the Department of Factories Inspectorate.
The five lathe killers
| Hazard | How it hurts | The rule |
|---|---|---|
| Entanglement | Sleeve, glove, hair, rag, jewellery wraps round the chuck or work | Close-fitting clothes; no gloves at the lathe; hair tied; no rags near the chuck |
| Chuck key | Left in the chuck, it is thrown out at speed | Remove it every time; use a spring-loaded or self-ejecting key if you can |
| Swarf | Long hot ribbons cut deeply and fly into eyes | Safety glasses with side shields; stop the machine before clearing; use a hook and brush |
| Flying work | Work badly gripped or too long flies out of the chuck | Check the grip; support long work with the tailstock; start slowly |
| Lifting and slipping | A chuck weighs more than it looks; oil on the floor | Get help to lift; keep the floor clean and dry |
Check before every start: work properly centred and clamped in the chuck; all tools, measuring instruments and other objects removed from the bed and saddle. Rules vary by workshop and the machine's manual always comes first.
Tools and items for Unit 1
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Safety glasses with side shields | Clear shatter-resistant eyewear that stops swarf and chips from the side | Worn all the time at the machine | — |
| Close-fitting overalls | Cotton overall with buttoned cuffs; cannot catch on turning parts | Sleeves buttoned or rolled above the elbow | — |
| Safety boots | Steel toe-cap boots that protect from dropped chucks and hot swarf | Oil-resistant sole | — |
| Hair net or cap | Keeps long hair away from the chuck | — | |
| Chuck key | The handle that tightens the chuck jaws | Spring-loaded or self-ejecting type preferred | Chuck spanner |
| Chip hook | A hook on a handle that pulls swarf away without using the hand | About 300 mm | — |
| Brush | Stiff-bristled brush to sweep chips | — | |
| Isolator (main switch) | A lockable switch that cuts power to the machine | One per machine | Main switch |
| Fire extinguisher and first-aid box | Dry powder or CO2 extinguisher; first-aid kit | Near the exit | — |
SAFETY PROTOCOL: Centre lathe (general)
Before you start
- Dress: glasses on, sleeves buttoned, no gloves, rings, watch or chain, hair tied, boots on.
- Check the area: floor clean and dry, nothing on the bed or saddle, good light, clear space behind you.
- Check the machine: chuck guard in place, stop button works, chuck key is in your hand (never in the chuck), no damaged leads.
- Check the work: gripped firmly, long work supported, tool tight and at centre height, carriage hand-wheeled by hand to see it clears the chuck.
- Know where the isolator, extinguisher and first-aid box are. Lockout: for any repair, adjustment inside the headstock, or belt change, switch off at the isolator and lock it so nobody can switch it on.
While you work
- Do: keep one hand on the stop; take light cuts; stop the machine before measuring, clearing swarf, changing speed or cleaning; keep your head to one side of the line of the chuck.
- Do not: leave the chuck key in; wear gloves; use a rag or emery cloth held in the fingers on work that is turning; brake the chuck with your hand; lean over the chuck; talk to others while cutting; leave the machine running unattended.
After you finish
- Switch off and wait for the chuck to stop by itself. Isolate.
- Clear swarf with the hook and brush, wipe and lightly oil the bed, return tools and measuring instruments to their place, leave the guard closed.
- Report any fault, broken guard or odd noise in writing. Tag the machine "Do not use" if unsafe.
Emergency
- Stop the machine (stop button), then isolate at the main switch.
- Call for help. For serious injury call 112 (the national emergency number). Do not pull a trapped person: switch off first.
- Bleeding: press firmly with a clean cloth. Eye injury: do not rub; cover and get help. Burn: cool with clean running water. See a doctor or nurse after any injury (this is not medical training).
Lifting a chuck and bar
A 200 mm chuck can weigh 20 kg or more (example: check the maker's plate). Never lift a chuck alone onto the spindle. Use two people or a lifting aid and put a wooden board across the bed to protect the bedways. Long bar sticking out of the back of the headstock is a hazard: support it and mark it with a tape or flag. Lifting machines and tackle are covered by Act 328 sections 44 to 47, including safe working load and a register. Ask a GhIE-registered engineer about any lifting beam or hoist.
Safety walk-round
- With your instructor, find on your lathe: the stop button, the isolator, the chuck guard, the chuck key and the light.
- Put on the right clothes and say what would go wrong with each item you remove (glove, ring, loose sleeve).
- Demonstrate the key rule: pick up the chuck key, tighten the chuck, take the key out, show it to the instructor, and put it in its hook.
- Practise a stop: with the machine off and isolated, show how you would stop it and isolate it in an emergency.
- Clear a pile of old swarf using only the hook and brush.
- Fill in the daily check sheet (Appendix E) for the machine.
Safety poster
Draw a one-page poster with the five lathe killers and one rule for each, in your own words. Pin it up at home or in the workshop and write down the reaction of the first person who reads it.
Check yourself
- Why are gloves banned at a lathe?
- What must you do with the chuck key before pressing the start button?
- Why stop the machine before clearing swarf?
Unit 2 · Know the lathe: parts and controls
You cannot work safely on a machine whose parts you cannot name. Learn every part, what it does and what it can do to you.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 2.1 Name the parts | names and points to all 15 numbered parts and says what each does |
| 2.2 Use the controls | sets speed, feed and direction correctly and moves the slides by hand |
| 2.3 Calculate speed | works out spindle speed in rev/min from the cutting speed and diameter |
| 2.4 Look after the machine | does the daily check and cleaning |
Range. A centre lathe of about 300 mm swing. Evidence. Labelling test; speed calculation; daily check sheet.
Ask a qualified expert. Electrical faults, gearbox repairs and moving or installing a lathe must be done by a licensed electrician or a qualified machinist. Ask a GhIE-registered engineer about the foundation, levelling and anchoring of a heavy machine. This unit teaches operating and daily care only.
What a lathe does
A centre lathe holds the work and turns it while a cutting tool, held in a tool post on a carriage that slides along the bed, removes metal. The main parts are the bed, headstock, tailstock, carriage (saddle and apron), cross-slide, compound rest, tool post, lead screw and chuck. Operations include facing, turning, drilling, threading and knurling.
Photo credit: Glenn McKechnie, CC BY-SA 3.0. Cropped, resized and numbered for this manual.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Headstock | Houses the spindle and gears; the speed and feed levers are on its front | Change speed only when the machine has stopped |
| 2 | Chuck | Grips the work at the end of the spindle | Check the grip and take the key out before every start |
| 3 | Tool post | Holds the cutting tool on top of the cross-slide and compound rest | Tighten with the proper key; keep the tool overhang short |
| 4 | Tailstock | Supports the far end of the work or holds a drill or centre | Lock it to the bed before cutting |
| 5 | Carriage handwheel (on the apron) | Moves the carriage along the bed by hand | Check the carriage cannot reach the chuck before you start |
| 6 | Lead screw | The long threaded rod that drives the carriage for screw cutting | Never touch it while it turns |
| 7 | Bed (slideways) | The long, flat base that guides the carriage and tailstock | Keep it clean; never leave tools or a chuck key on it |
| 8 | Emergency stop | The red button that stops the machine at once | Know where it is; test it; never block it |
This machine also has a digital display, a work lamp and a clear chuck guard. Your lathe may not have all of these, and its levers will be in other places: read your own machine's plate.
Parts table: centre lathe
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Bed | The long, heavy, precisely ground base with slideways that guide the carriage and tailstock | Keep it clean and lightly oiled; never hammer on it or leave tools or a chuck key on it |
| 2 | Headstock | Houses the spindle, bearings and the gears or belts that set the speed | Never open covers while the machine is connected; isolate first |
| 3 | Spindle (and chuck body) | The hollow shaft that turns; the chuck is mounted on its nose | Never lift or fit a chuck alone; never run bar out of the back unsupported |
| 4 | Chuck jaws | Three or four jaws that grip the work | Check grip before every start; remove the key |
| 5 | Tailstock | Slides on the bed to support the far end of the work or to hold a drill or centre | Lock it before cutting; do not extend the barrel beyond its safe length |
| 6 | Carriage (saddle) | Slides along the bed carrying the cross-slide and tool | Check it cannot hit the chuck before starting |
| 7 | Cross-slide | Moves the tool in and out, at right angles to the bed; sets the depth of cut | Read the dial carefully: on most lathes one division on the cross-slide dial takes off twice that from the diameter (check yours) |
| 8 | Compound rest | Sits on the cross-slide and can be swivelled to set a tool at an angle; used for short tapers and chamfers | Lock it; keep it clear of the chuck |
| 9 | Tool post | Holds the cutting tool at the right height | Tighten with the proper key; keep the tool overhang short |
| 10 | Lead screw | A long threaded rod driven by the headstock gears; it moves the carriage for screw cutting | Never touch while it turns; use only for threading |
| 11 | Feed rod | A long smooth shaft driven by the headstock; it drives the carriage for turning and facing | Do not touch while it turns |
| 12 | Apron handwheel and controls | Handwheel moves the carriage by hand; levers on the apron engage the power feed or thread | Engage only one of feed or thread at a time; know where the stop is |
| 13 | Speed and feed selectors | Levers or dials on the headstock that set the spindle speed and the feed | Change speed only when the machine has stopped (unless the maker says otherwise) |
| 14 | Tailstock handwheel and barrel | Moves the barrel in and out to push a drill or centre into the work | Lock the barrel before drilling; fit drills and centres cleanly |
| 15 | Tailstock lock lever | Clamps the tailstock to the bed | Always lock before cutting; check again after moving it |
The work itself (the bar in green on the diagram) is called the workpiece. The cutting tool is held in the tool post (9).
Your lathe may differ. Many machines in Ghana workshops are older or imported second-hand. Controls are in different places and may be marked in inches or have different gear charts. Read the plate on your own machine and ask the instructor to show you each control. A control you do not understand is a control you leave alone.
Speed: how fast should the work turn?
Cutting speed is how fast the surface of the work passes the tool, in metres per minute. The spindle speed in revolutions per minute is RPM = (1000 × cutting speed) ÷ (π × diameter in mm). Plain high-speed steel (HSS) tools, one-hour tool life, dry cutting and medium feeds give about 3 to 38 m/min on mild steel, 90 to 210 on brass and 122 to 305 on aluminium. Cast iron of medium grade runs much slower (1 to 2 m/min in the same table). Coolant or a different tool can change these. In your first weeks use the low-middle of each range and use cutting oil on steel.
Worked examples (checked by script).
- Mild steel, 30 mm diameter, 25 m/min: RPM = 1000 × 25 ÷ (π × 30) = 265 rev/min.
- Mild steel, 50 mm diameter, 25 m/min: 159 rev/min.
- Brass, 25 mm diameter, 100 m/min: 1,273 rev/min.
- Aluminium, 30 mm diameter, 150 m/min: 1,592 rev/min.
- Check back: 30 mm at 400 rev/min gives a surface speed of π × 30 × 400 ÷ 1000 = 37.7 m/min, near the top of the HSS mild steel range, so for a beginner that is too fast.
Use the speed your lathe has closest below the calculated one. A big diameter must turn slower than a small one for the same cutting speed.
Feed is how far the tool moves for each turn of the work, in mm per revolution. For turning, a feed of 0.1 mm/rev is a safe finishing start for beginners (example, check the tool maker's chart) and 0.15 to 0.25 for roughing with a good tool. Time to turn = length ÷ (feed × RPM): 100 mm at 0.1 mm/rev and 265 rev/min is 100 ÷ 26.5 = 3.8 minutes per pass.
Daily care: get the best out of the machine
- Wipe the bed and slideways clean; oil them lightly (use the oil the maker names).
- Check oil level sights and top up. Check the cross-slide and compound screws move smoothly, with no stiff spots.
- Look at belts and guards; check for cracked or loose ones.
- Run the machine empty for two minutes and listen: any new noise is a fault. Switch off and report.
- At the end of the day: clean all swarf, wipe with an oily cloth, close the guards.
Tools and items for Unit 2
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Oil can | Squirt can for slideway oil | 250 to 500 ml | — |
| Cutting oil | Oil or soluble oil that cools and lubricates the cut on steel | Brush on or drip | — |
| Lathe manual or maker's plate | Gives the speed chart and the oil points | — | |
| Dial indicator on stand (L2 detail) | Instrument that shows tiny movements | 0.01 mm | — |
| Cleaning rags | Cotton rags for wiping the machine when it is stopped | Never near the turning chuck | — |
SAFETY PROTOCOL: Changing speed and feed, and daily care
Before
- Machine stopped and chuck at rest; key out. Isolate if you will open any cover.
While
- Do: select the speed from the chart; move selectors gently; spin the chuck by hand to make sure gears have engaged.
- Do not: force a lever; change speed while the spindle is turning (unless the maker's manual says it is allowed); use a rag near the turning chuck.
After
- Guards closed; carriage parked clear of the chuck; machine isolated.
- Write down any fault on the log.
Emergency
- Gear crash or noise: stop and isolate. Smell of burning or smoke: stop, isolate, use the extinguisher only if you are trained and it is safe, and call 112 for a fire you cannot control.
Label the lathe
- Without looking at the table, name the 15 parts on a blank copy of the diagram, then check yourself.
- With the machine stopped, wind the carriage up and down by hand and say which parts move.
- Turn the cross-slide handle one full turn and note how far the tool moves. Check what one division on the dial is.
- Work out the RPM for three sizes of bar and three materials. Find the nearest speed on your lathe.
- Do the daily check and sign the sheet.
Speed table
Work out the spindle speed (rev/min) for mild steel at 25 m/min for diameters 20, 30 and 50 mm. Then for brass at 100 m/min at 20 mm.
Speed card
Make a pocket card with the lathe's available speeds and the best speed for 10, 20, 30 and 40 mm mild steel and brass. Keep it in your logbook.
Check yourself
- Which part moves the tool in and out at right angles to the bed?
- Which long shaft is used only for screw cutting?
- For the same cutting speed, does a big bar turn faster or slower than a small one?
Unit 3 · Hold the work and the tool
Most bad work comes from bad holding. If the work moves, the tool digs. If the tool is too low, it rubs. Hold firmly, hold true, hold short.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 3.1 Hold work in a chuck | mounts round bar in a three-jaw chuck, grips it firmly and runs it true |
| 3.2 Use a four-jaw chuck | names when it is needed and why it is set by hand |
| 3.3 Support long work | uses a centre in the tailstock when the work is long |
| 3.4 Set a tool | grinds or selects a tool, fits it at centre height with short overhang |
Range. Round bar 12 to 40 mm; HSS and brazed tools. Evidence. Observation; a bar run true to 0.1 mm.
Ask a qualified expert. Fitting heavy chucks, faceplates and large work is a lifting task: use two people or a lifting aid and ask a GhIE-registered engineer about any lifting device. Grinding tools on a bench grinder needs eye protection, a correct rest gap and a guard; ask a qualified safety officer to check the grinder.
The three-jaw chuck
A three-jaw self-centring chuck has three jaws that move together when the key turns a scroll plate inside. It grips round and hexagonal bar and holds it nearly central. It is quick but not perfectly true: a little error is normal, and wear makes it worse.
Photo credit: Glenn McKechnie, CC BY-SA 3.0. Cropped, resized and numbered for this manual.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Chuck body (front face) | The heavy steel body; it is stamped with its size and a maximum speed | Never run the chuck faster than the speed stamped on it |
| 2 | Jaw (fitted) | A stepped block that grips the work; the three jaws move together | Use the jaws in their own numbered slots only |
| 3 | Central bore | The hole through the middle where bar can pass | Support long bar behind the headstock |
| 4 | Jaw taken out (underside) | Its row of teeth fits the scroll thread inside the chuck | Keep the teeth and slot clean; refit in the right slot |
| 5 | Chuck key (shown beside the chuck) | The T-shaped key that turns the scroll and so moves the jaws | Take the key out every time; never leave it in the chuck |
| 6 | Scroll thread (seen in the empty slot) | The spiral thread that moves all three jaws together when the key turns | Keep it clean and lightly oiled; do not force it |
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Chuck body | The heavy steel body that holds everything | Never lift alone; never strike it |
| 2 | Central bore | The hole through which bar can pass | Support long bar behind the headstock |
| 3 | Key socket | The square hole where the key turns the scroll | Remove the key every time; never leave it in |
| 4 | Jaw | A stepped block that grips the work; the three jaws move together | Keep them clean; use them in the numbered slots only |
| 5 | Backplate and mounting | Joins the chuck to the spindle nose (bolted, threaded or camlock) | Check the lock marks line up; never mount on a dirty nose |
The four-jaw chuck has four jaws, each moved on its own. It holds square, rectangular and odd-shaped work and lets you set the work exactly central by adjusting each jaw while watching a dial indicator or chalk mark.
Mounting and running work true (step by step)
Mount bar in a three-jaw chuck
- Stop and isolate. Remove the key from its hook only when you need it.
- Open the jaws a little wider than the bar. Push the bar in with about 15 to 20 mm showing behind the jaws gripped, and as little sticking out as the job needs. Long overhang springs the work.
- Tighten the jaws by turning the key in each of the three key sockets in turn, a little at a time, so the grip is even.
- Remove the key. Show it to the instructor.
- Spin the chuck by hand and look at the bar end. If it wobbles, loosen, tap the bar, re-tighten, and repeat.
- For work longer than about 3 times its diameter, support the free end with a centre in the tailstock (the work needs a small centre hole first, Unit 5).
- Lock the tailstock; check it does not touch the work while turning.
The tool and its parts
A single-point cutting tool has one cutting edge. Its shape controls how it cuts: the angles are called rake (the slope of the top face) and clearance (the slope under the edge so it does not rub).
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Shank | The square body held in the tool post | Hold with short overhang; do not use a bent shank |
| 2 | Nose | The tip that does the cutting | Keep it sharp; a blunt nose rubs and overheats |
| 3 | Top face (rake) | The face the chip slides across | A small positive rake cuts easily; very sharp edges chip |
| 4 | Side flank | Ground away under the side cutting edge so it does not rub | Do not grind to zero clearance |
| 5 | End flank | Ground away under the end so the tip clears the work | Same |
| 6 | Base | Flat seat that sits on the tool post or packing | Keep it clean and flat |
Typical angles for HSS on mild steel (starting values, from general machining practice; check your instructor's chart): top rake 8 to 12 degrees, side clearance 6 to 8 degrees, front clearance 6 to 8 degrees. For brass use almost zero rake.
Setting the tool at centre height
The cutting tip must be at the height of the spindle centre line. Too high: it rubs and does not cut. Too low: the work climbs over the tool and it digs in.
Set a tool to centre height
- Stop and isolate. Fit the tool in the tool post with as short an overhang as possible (about 1.5 times the shank thickness at most).
- Bring a steel rule upright against the faced end of the work and look where the tool tip meets it, or compare the tip against the tip of the tailstock centre set to the same height.
- Add or remove thin packing (strips of steel) under the tool until the tip is at the same height as the centre.
- Tighten the tool post screws evenly with the key and remove the key.
- Hand-wheel the carriage to check the tool is clear of the chuck.
Sharpening an HSS tool on the bench grinder
The tool must be sharpened at the bench grinder using the tool rest, with safety glasses on, taking light touches and cooling in water often. Never grind with the wheel unguarded or cracked.
SAFETY PROTOCOL: Bench grinder (sharpening lathe tools)
Before
- Glasses on (and face shield if you have one); no gloves, no loose sleeves; hair tied.
- Check the wheel is not cracked or worn. Rest gap not more than 3 mm from the wheel (check your maker's manual); guard in place; isolator.
- Stand to one side while the wheel gets to speed.
While
- Do: grind with light pressure on the face; keep the tool moving; cool the tool in water; use the tool rest.
- Do not: grind on the side of the wheel; push hard; hold the tool without the rest; grind aluminium or brass on the same wheel as steel without dressing.
After
- Switch off and let the wheel stop. Brush up grinding dust. Report a worn or cracked wheel; do not use it.
Emergency
- Wheel breaks or sparks fly into the eye: stop, isolate, get first aid; call 112 for a serious eye or head injury.
Tools and items for Unit 3
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Three-jaw chuck | Self-centring jaws; holds round and hex bar | 125 to 200 mm | Lathe chuck |
| Four-jaw chuck | Independent jaws; holds square or odd work and is set true by hand | 160 to 250 mm | — |
| Chuck key | Turns the scroll; fits a square socket | Match the chuck | — |
| Live or dead centre | A pointed or revolving cone in the tailstock that supports the work end | Morse taper 2 or 3 (L2) | — |
| Centre drill (combination drill) | Short drill that makes a small centre hole and countersink in the work end | No. 2 or 3 | — |
| HSS tool bit | A square or round bar of high-speed steel, ground to shape | 8 to 12 mm square | — |
| Tool post key | The spanner for the tool post screws | — | |
| Packing strips | Thin steel strips under the tool to adjust height | 0.5 to 3 mm | — |
| Bench grinder | Two grinding wheels on a motor, with tool rests and guards | 150 to 200 mm wheel | — |
| Grinding wheel dresser | Tool that cleans and flattens a loaded wheel | — | |
| Steel rule | Rule to compare heights and measure lengths | 150 or 300 mm | — |
Hold and set
- Mount a 25 mm mild steel bar in the three-jaw chuck, 40 mm out, and run it true.
- Grind an HSS tool to the angles on the table. Compare yours with the instructor's.
- Fit the tool and set it to centre height using a rule and packing.
- Mount the bar between chuck and tailstock centre (the instructor demonstrates).
- Fill in the set-up sheet (Appendix E).
Tool angles
Draw a side view of a turning tool and mark top rake, side clearance and front clearance. Write one sentence on what goes wrong if clearance is zero.
Check yourself
- Where must the tool tip be in relation to the spindle centre line?
- When do you use a four-jaw chuck?
- Why keep the overhang of the work short?
Unit 4 · Measure and read a drawing
If you cannot measure, you cannot machine. A lathe takes off metal in thousandths of a millimetre, but only as accurately as your eye and your caliper can read.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 4.1 Measure with a rule and caliper | reads a vernier caliper to 0.02 mm and checks the zero |
| 4.2 Measure with a micrometer | reads an outside micrometer to 0.01 mm |
| 4.3 Read a simple drawing | finds sizes, tolerances and the material from a drawing |
| 4.4 Apply a general tolerance | knows what accuracy applies when none is written |
Range. Round parts 5 to 50 mm. Evidence. Five measurements read correctly; a drawing read aloud.
Ask a qualified expert. Measurements for parts that carry loads, hold pressure or are used on vehicles, lifts or structures are an engineer's responsibility. Ask a GhIE-registered engineer before you make any part where a failure could hurt someone. Standards numbers in this unit are international; check them against the Ghana Standards Authority text.
The vernier caliper
A vernier caliper measures outside diameters, inside diameters, steps and depths. A common type reads to 0.02 mm (50 divisions on the sliding scale); cheaper ones read 0.05 mm. Always check the zero with the jaws closed. Do not force the jaws on the work: a light touch gives the true size.
Photo credit: ArtMechanic, CC BY-SA 3.0. Cropped, resized and numbered for this manual.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Fixed outside jaw | Part of the beam; one face for an outside size | Do not use it as a scriber or hammer |
| 2 | Sliding outside jaw | Moves to close on the work | Close it on the work gently |
| 3 | Inside jaws (the small upper nibs) | Open inside a hole to read an inside size | Keep the tips clean and undamaged |
| 4 | Main scale | The fixed millimetre marks on the beam | Keep it clean; read straight on |
| 5 | Vernier scale | The sliding scale that gives the fine reading | Find the line that lines up with a main-scale line |
| 6 | Locking screw | Locks the slider so you can read the size away from the work | Do not overtighten |
| 7 | Resolution marking (0.02 mm) | Printed on the slider; tells the smallest step this caliper reads | Read the marking on your own caliper first |
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Fixed outside jaw | The fixed jaw for outside size | Do not use it as a scriber or hammer |
| 2 | Fixed inside jaw | The small fixed nib for inside size | Keep the tip clean and undamaged |
| 3 | Vernier scale | The sliding scale that gives the fine reading | Read straight on, not from the side |
| 4 | Sliding outside jaw | Moves to close on the work | Close on the work gently |
| 5 | Sliding inside jaw | Moves to open an inside size | Same |
| 6 | Locking screw | Locks the reading so you can read it away from the work | Do not overtighten |
| 7 | Thumb roller | Moves the slider with the thumb | Use thumb pressure only |
| 8 | Main beam and scale | The long bar with the millimetre scale | Keep it clean; oil lightly when stored |
| 9 | Jaw faces | The flat faces that touch the work | Clean before every measurement |
Reading a 0.02 mm caliper (worked example). The zero of the sliding scale is just past the 24 mm mark on the main scale. The 13th line of the vernier lines up exactly with a main-scale line. Reading = 24 + 13 × 0.02 = 24.26 mm.
Never measure work that is turning. Stop the machine and clean the work first.
The outside micrometer
An outside micrometer measures to 0.01 mm. A sleeve (barrel) carries the main scale in 0.5 mm steps and a thimble carries 50 divisions; one turn is 0.5 mm. Always close it gently with the ratchet so that every reading uses the same pressure, and check the zero with the anvil and spindle closed. Hold it by the heat-insulating pad when you can so that your hand does not warm it.
Photo credit: Nicolas Buffler, CC BY 2.0. Cropped, resized and numbered for this manual.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Frame | The C-shaped body that holds the anvil and the sleeve | Do not drop it; a knock can bend it |
| 2 | Anvil | The fixed measuring face | Keep it clean and free of scratches |
| 3 | Spindle | The moving measuring face, turned by the thimble | Never use it on turning work |
| 4 | Spindle lock | The small lever that locks the reading | Release it before closing or cleaning |
| 5 | Sleeve (barrel) scale | The fixed scale along the sleeve | Read the sleeve first, then the thimble |
| 6 | Thimble scale | The rotating scale; the marking on this one says 0.01 mm | Turn it only by the ratchet when closing on the work |
| 7 | Ratchet knob | Slips at a set force so every reading uses the same pressure | Always finish closing with the ratchet |
The marking on this frame reads 0 to 25 mm and 0.01 mm: it measures sizes from 0 to 25 mm in steps of 0.01 mm.
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Frame | The C-shaped body that holds the anvil and barrel | Do not drop it; a knock can bend it |
| 2 | Anvil | The fixed measuring face | Keep it clean; no scratches |
| 3 | Spindle | The moving measuring face turned by the thimble | Never use it on turning work |
| 4 | Spindle lock | Locks the reading | Release before cleaning |
| 5 | Sleeve (barrel) | Carries the main scale | Read it before the thimble |
| 6 | Thimble | The rotating scale on the barrel; 50 divisions of 0.01 mm | Turn it by the ratchet to close |
| 7 | Ratchet stop | Slips at a fixed force so each measurement is the same | Always finish with it |
| 8 | Insulating pad | Heat-insulating pad you hold so the frame does not warm | Use it |
Reading (worked example). Sleeve shows 12 mm and one extra half-millimetre line, so 12.5 mm. The thimble line at 27 divisions lines up with the datum: 27 × 0.01 = 0.27 mm. Reading = 12.5 + 0.27 = 12.77 mm.
Care. Store a micrometer with the faces open a little (not touching), wiped clean and lightly oiled. Calibrate against a gauge block or a known standard from time to time (L3, Unit 4).
Reading a simple drawing
A drawing tells the maker the shape, size, material and accuracy. In the title block (usually the bottom right) you find the part name, the material, the scale, the units (usually millimetres) and the general tolerance. Dimension lines show sizes; a line with a number and "Ø" means a diameter. A section view shows the inside.
Example: the clamp pad (the first part you make). A pad for the screw clamp: round bar, mild steel, 20 mm diameter, 12 mm long, with a 6 mm hole drilled in one face to a depth of 8 mm and a 1 mm × 45 degree chamfer on the outer edge. General tolerance ISO 2768-m.
How close is close enough? General tolerances
When a size has no tolerance written beside it, the drawing's general tolerance note applies. ISO 2768-1 (an international standard) gives classes f (fine), m (medium), c (coarse) and v (very coarse). Check the ISO text or the Ghana Standards Authority edition when you can read it; sources disagree on printed tables.
| Size range (mm) | f (fine) | m (medium) | c (coarse) | v (very coarse) |
|---|---|---|---|---|
| 0.5 to 3 | ±0.05 | ±0.1 | ±0.2 | n/a |
| over 3 to 6 | ±0.05 | ±0.1 | ±0.3 | ±0.5 |
| over 6 to 30 | ±0.1 | ±0.2 | ±0.5 | ±1 |
| over 30 to 120 | ±0.15 | ±0.3 | ±0.8 | ±1.5 |
| over 120 to 400 | ±0.2 | ±0.5 | ±1.2 | ±2.5 |
| over 400 to 1000 | ±0.3 | ±0.8 | ±2 | ±4 |
ISO 2768-2 (geometrical classes) has been withdrawn and replaced by ISO 22081:2021. Example: a 20 mm diameter marked "ISO 2768-m" may be anywhere from 19.8 to 20.2 mm.
Tools and items for Unit 4
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Steel rule | Hardened rule with fine graduations | 150, 300 mm | — |
| Vernier caliper | Measures outside, inside, step, depth | 0 to 150 mm, 0.02 mm | — |
| Digital caliper | Same, with a display | 0 to 150 mm | — |
| Outside micrometer | Precise outside diameter | 0 to 25 mm, 25 to 50 mm | — |
| Scriber | Hardened point for scratching a line | — | |
| Engineer's square | A steel try-square with a right angle | 100 or 150 mm | — |
| Centre punch | Makes a small dent to start a drill | — | |
| Engineer's blue (marking blue) | Dye painted on metal so scribed lines show | — | |
| Surface plate (or flat glass) | A flat reference table | — |
Measure ten ways
- Check the zero on a caliper and a micrometer. Write them in your logbook.
- Measure five pieces of round bar with the caliper and then the micrometer. Compare and note any difference.
- Measure an inside diameter and a depth with the caliper.
- Read the drawing of the clamp pad and list: material, diameter, length, tolerance, chamfer.
- Write down the lowest and highest sizes allowed for the 20 mm diameter under ISO 2768-m.
Reading the instruments
(a) A 0.02 mm caliper shows 31 mm on the main scale and the 7th vernier line matches. What is the size? (b) A micrometer shows 8.0 mm on the sleeve, no half-line, and the thimble reads 0.44. What is the size? (c) A 40 mm length marked ISO 2768-m: lowest and highest size?
Find the zero
At home or at work, find three things you can measure with a caliper (a bolt, a coin, a pipe). Measure each, write the size and what instrument you used.
Check yourself
- What must you check on a caliper before using it?
- Why use the ratchet on a micrometer?
- What tolerance applies if none is written?
Unit 5 · Face, turn, drill and part off
Facing makes the end flat. Turning makes the diameter right. Drilling and parting finish the job. Four operations make most parts.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 5.1 Face an end | faces a bar end flat and square at the right speed and feed |
| 5.2 Turn to a diameter | turns a diameter to size within 0.1 mm by taking roughing and finishing cuts |
| 5.3 Drill on the lathe | centre-drills and drills a hole to depth from the tailstock |
| 5.4 Chamfer and part off | cuts a 45 degree chamfer and parts off to length without damage |
| 5.5 Fix common faults | recognises chatter, taper, rough finish and fixes them |
Range. Mild steel and brass bar 12 to 30 mm. Evidence. Three parts measured and passed; fault diary.
Ask a qualified expert. Parts that carry loads, hold pressure or are used on vehicles, lifts or structures need an engineer's design: ask a GhIE-registered engineer. Machine only the parts you are trained for and authorised to make. For any injury, see a doctor or nurse.
The dial and the depth of cut
Each turn of the cross-slide screw moves the tool a fixed distance; the dial has divisions. On many lathes the cross-slide dial reads radius (the tool moves in by the dial amount, so the diameter reduces by twice that). Some are marked in diameter. Check your lathe by taking a trial cut and measuring. The depth of cut is how much radius you remove; diameter reduction = 2 × depth of cut. To go from 30 mm to 28 mm you cut 1 mm deep.
Roughing and finishing. Take roughing cuts of 1 to 1.5 mm depth (light for a small lathe) and leave 0.3 to 0.5 mm on the diameter. Then take a finishing cut of 0.1 to 0.2 mm at a slower feed. To reduce 30 mm to 20 mm at 1.5 mm depth you need 10 ÷ 2 ÷ 1.5 = 3.33, so about 3 roughing cuts and a finishing cut (checked by script).
Facing (step by step)
Face the end of a bar
- Stop and isolate. Mount the bar so that about 20 mm stands out. Fit a facing tool or a turning tool set at centre height, angled slightly so only the tip touches.
- Set the speed for the diameter (Unit 2). Remove the key. Start the machine.
- Bring the tool in until it just touches the end near the outside, and wind it out clear.
- Move the carriage in by 0.2 to 0.5 mm with the compound or carriage (lock the carriage to the bed).
- Feed the tool across the face from the outside to the centre (or centre outwards) by the cross-slide handle, steadily, in one smooth movement.
- Stop and check the face with a straightedge or the edge of a rule; there should be no raised centre pip.
- Repeat a light finishing cut if the surface is rough.
Turning to a diameter (step by step)
Turn a plain diameter
- Face the end. Set the carriage at the end of the bar.
- Move the tool until it just touches the surface; set the cross-slide dial to zero.
- Wind the carriage back past the end. Put on the roughing cut (about 1 mm).
- Start the machine. Feed the carriage along by hand or by the power feed, about 20 mm only for the first trial.
- Stop. Wind the tool clear without moving the cross-slide. Measure the diameter with a caliper.
- Adjust the cross-slide for the next cut. Repeat until you are 0.3 to 0.5 mm over size.
- Take a finishing cut: slower feed, light depth (0.1 to 0.2 mm). Measure. Stop when the diameter is right.
- Chamfer the end with the tool turned to 45 degrees or with a file held at an angle while the machine is turning (hold the file by the handle only and reach over the work from a safe position; ask your instructor).
Note on filing at the lathe: file with the handle in the left hand and the tool away from the chuck, with the left hand held back from the chuck. Use a file with a handle, never emery cloth held by hand. This is the safer way and still a risk: ask your instructor.
Drilling on the lathe (step by step)
Centre drill and drill a hole
- Face the end. Put a centre drill in a drill chuck in the tailstock. With the lathe turning at a medium speed, wind the tailstock barrel in to make a small centre hole.
- Replace the centre drill by a twist drill of the right size (hole size minus a small allowance for a reamed hole, or exact for a tap drill: see tables).
- Choose the speed: for a 10 mm drill in mild steel at 25 m/min, 796 rev/min; for 8.5 mm, 936 rev/min (worked by script).
- Run the drill in slowly, using the barrel handwheel, and withdraw it often to clear the swarf (called "pecking"). Use cutting oil.
- Drill to the marked depth. Stop. Never let go of the handwheel with the drill in the work.
- Never hold the drill chuck by hand if it spins; if the drill grabs, stop the machine at once.
Parting off
Parting uses a thin blade, the parting tool, to cut the finished part from the bar. It must be set exactly at centre height, square to the work, with a slow feed and plenty of cutting oil. It is the operation most likely to grab and jam: use a low speed (about half of normal), keep the overhang short, and stop the machine if it chatters. Support long parts with a hand-held rag held at a safe distance only as your instructor shows you, never wrapped round the work.
| Fault | Cause | Fix |
|---|---|---|
| Tool jams | Too fast; tool above or below centre; blade too long | Slower; reset height; shorter overhang |
| Part falls into the swarf | Not caught | Place a tray or hold the part with a hooked rod as taught |
| Rough part-off face | Blunt or wrong tool | Sharpen; feed steadily |
SAFETY PROTOCOL: Facing, turning, drilling and parting
Before
- Work gripped, key out, guard in place, tool at centre height, carriage clear of the chuck, speed set from the chart.
While
- Do: stop to measure, clear swarf, or change tool; use cutting oil with a brush only while the work is stopped or from the safe side; take light cuts; keep your free hand on the stop.
- Do not: wear gloves; reach across a turning chuck; use a rag on turning work; leave the machine to talk to someone; touch swarf with your hand.
After
- Stop, isolate, hook and brush swarf into the bin, wipe the machine, return tools.
Emergency
- A jam or crash: press stop, isolate, check for injury, report. A cut or eye injury: first aid and a doctor or nurse; call 112 for a serious one. A fire (oily rags): isolate, use the extinguisher if safe and call 112 if it spreads.
Tools and items for Unit 5
| Item | What it is and its use | Size or type | Also called |
|---|---|---|---|
| Facing tool | A tool ground with the cutting edge to the side so it can cut across the end | HSS, 8 to 12 mm | — |
| Roughing tool | A tool for taking heavy cuts along the work | HSS | — |
| Finishing tool | A tool with a slightly larger nose radius for a smooth surface | HSS | — |
| Parting tool (cut-off blade) | A thin blade that cuts the part from the bar | 2 to 3 mm blade | — |
| Centre drill | Starts a drill accurately | — | |
| Twist drill | Standard drill bit | 3 to 16 mm | Drill bit |
| Drill chuck | A three-jaw chuck for drills with a Morse taper arbor | 0 to 13 mm | — |
| Cutting oil | Cools and lubricates the cut | — | |
| Hand file with handle | For deburring and chamfering | 200 mm | — |
| Deburring tool | Hand tool that removes burrs | — | |
| Chip tray | Catches swarf | — |
Plan the cuts
A bar 30 mm diameter is to be turned to 24 mm over 40 mm length, in mild steel, at 25 m/min. (a) The speed? (b) The number of 1.5 mm roughing cuts? (c) Time per pass at 0.1 mm/rev?
Make a stepped pin
- Cut a 25 mm mild steel bar to 80 mm. Face both ends.
- Turn a 40 mm length down to 20 mm, with a 1 mm chamfer. Measure.
- Centre drill and drill a 6 mm hole 15 mm deep in the large end.
- Part off or saw to 60 mm, and face the cut end.
- Check dimensions against the drawing and record in your logbook.
Fault diary
In your logbook, write down every fault you meet (chatter, taper, rough finish, tool rub) with the cause you found and what fixed it. Add a diary page each week.
Check yourself
- How much does the diameter drop for a 1 mm depth of cut?
- Why use a lower speed for parting?
- What do you do before you measure the work?
Unit 6 · Make your first finished pieces
A good part is cut to size, finished well, and checked. Today you make the pad and the handle of your clamp, and you write down how you made them.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 6.1 Plan the work | writes a process sheet before starting |
| 6.2 Make two parts | makes the pad and the handle to the drawing |
| 6.3 Check the work | measures key sizes and records them |
| 6.4 Diagnose faults | uses the fault chart and the mistake catalogue |
Range. Mild steel and brass bar. Evidence. Two finished parts, process sheet, inspection record.
Ask a qualified expert. If a clamp or any made part will be used where failure could hurt someone, ask a GhIE-registered engineer to check the design and the material. Do not sell a part for lifting or pressure use. Ask a qualified safety officer about machine guarding in your workshop.
A process sheet
A process sheet lists the operations in order, the tools, the speeds and the checks. It prevents the commonest mistake: starting in the wrong order. Always face the end first, work from the chuck end towards the tailstock, rough then finish, and part off last.
Part 1: the pad (mild steel, 20 mm bar). Drawing: Ø18 ± 0.2 (ISO 2768-m), 12 mm long, 6 mm hole 8 mm deep in the back, 1 × 45° chamfer on the front edge, flat face.
| Step | Operation | Tool | Speed (rev/min) | Check |
|---|---|---|---|---|
| 1 | Mount 20 mm bar, 25 mm out | Chuck | Runs true | |
| 2 | Face the end | Facing tool | 398 | Flat |
| 3 | Turn Ø18 for 15 mm | Roughing, then finishing | 442 | 18.0 ± 0.2 |
| 4 | Centre drill and drill Ø6, 8 deep | Drill | 1,326 (at 25 m/min) | Depth |
| 5 | Chamfer 1 × 45° | Tool or file | 442 | Size |
| 6 | Part off at 12.5 mm and face to 12 | Parting tool, facing tool | 200 | 12 ± 0.2 |
(Speeds worked by script: 20 mm at 25 m/min = 398; 18 mm = 442; 6 mm = 1,326.)
Part 2: the handle (mild steel, 10 mm bar). Drawing: Ø8 ± 0.2, 120 mm long, with a 12 mm ball end or a 1.5 mm chamfered end at both ends. It is cut and finished the same way, supported by the tailstock when long; the ends are chamfered 1.5 × 45°.
Inspection record (what the checker writes)
| Part | Dimension | Drawing | Actual | Pass? |
|---|---|---|---|---|
| Pad | Ø | 18 ± 0.2 | ||
| Pad | Length | 12 ± 0.2 | ||
| Pad | Hole Ø | 6 ± 0.2 | ||
| Handle | Ø | 8 ± 0.2 | ||
| Handle | Length | 120 ± 0.5 |
Fault-finding chart
| Fault | Likely cause | Fix |
|---|---|---|
| Chatter (wavy surface) | Too much overhang, loose tool, speed too high, blunt tool | Shorten overhang; tighten; slower; resharpen |
| Taper (one end bigger) | Tailstock off line, worn bed, work springing | Check alignment (L2); support work |
| Rough finish | Blunt tool, feed too high, wrong speed | Sharpen; slower feed; correct speed |
| Tool rubs and squeals | Tool above centre; no clearance | Reset height; grind clearance |
| Work too small | Misread dial; no trial cut | Add allowance; measure before final cut |
| Diameter oversize at start | Chuck grip slipped | Grip better; support |
| Burrs on edge | No deburring | Deburr with a file |
| Hole off centre | No centre drill | Use a centre drill first |
Mistake catalogue (Level 1)
- Chuck key left in the chuck (never do it).
- Gloves or loose sleeves worn.
- Tool above or below centre height.
- Reading a micrometer a half-millimetre out.
- Not checking the zero.
- Taking a full-depth cut on the first pass.
- Measuring hot work (it shrinks as it cools).
- Skipping the finishing cut.
- Forgetting the chamfer, leaving sharp edges.
- Running the machine with swarf piled up.
Make the pad and the handle
- Write a process sheet for each part before you start (copy the format above).
- Make the pad. Measure it at each stage. Fill in the inspection record.
- Make the handle. Fill in the inspection record.
- Show both to your instructor; correct any fault.
- File the process sheets and records in your logbook.
One page review
Write one page on the biggest mistake you made on these parts, what caused it and how you would prevent it next time.
Check yourself
- What is the order of the first two operations on a bar?
- Why take a finishing cut?
- What should you record on the inspection sheet?
Unit 7 · Location, small business ideas and marketing yourself
A lathe that stands idle earns nothing. This unit shows what a machine shop can sell, where to set up, how to price machine time, and how to find customers.
Competency standard
| Learning outcome | Performance criteria — the trainee… |
|---|---|
| 7.1 Choose a location | explains what makes a good machine-shop site |
| 7.2 Price a job | works out a machine-hour cost and a job price |
| 7.3 Find customers | names ways to market and a plan for the first month |
| 7.4 Know the rules | lists the permit and registration steps (ask the offices) |
Range. A small shop offering turned parts and repairs. Evidence. A costed quote and a one-page plan.
Ask a qualified expert. This is general information, not legal, tax or financial advice. Ask a qualified lawyer before you act on registration, licence or contract matters; check tax with GRA or a qualified accountant; ask your bank before you borrow; ask a GhIE-registered engineer about machine installation and power. Prices here are examples and fees were not all verified.
What a small machine shop can sell
- Replacement parts: bushes, pins, shafts, spacers, pulleys, wheel studs for vehicles, garden and farm equipment (ask a qualified mechanic about vehicle parts).
- Repairs: rebuilding worn shafts, making a new thread, re-boring a bush.
- Small batches: hinge pins, bolts and nuts, clamps, handles.
- Subcontract work for fabricators and welders. Basic Welding Level 3 explains how welders subcontract machining; this is the other side of that arrangement.
- Training: teaching the apprentice.
Suame Magazine's machine-tool members already make bolts, nuts, gears and shafts, so the market for machined parts exists in Ghana; check what your own area needs.
Location settings that give good returns
- Near vehicle repair clusters, welders, farms with machinery and hardware shops, which all need parts.
- Near a steel and brass bar supplier.
- A dry, covered, level floor with good light and safe three-phase or single-phase power for the machine size (ask an Energy Commission-certified electrician and a GhIE-registered engineer).
- A site where noise and swarf do not disturb neighbours; room to store bar and finished parts securely.
- Near a good road for deliveries.
Pricing a machine job: the machine-hour cost
All figures are examples. A lathe cost GH¢60,000 (example), 10 years of life, scrap value GH¢6,000: depreciation (60,000 − 6,000) ÷ 10 ÷ 12 = GH¢450 a month. Monthly costs: depreciation 450, rent share 600, power 500, tooling and oil 300, operator 1,800 = GH¢3,650. If you can sell 120 productive hours a month, the machine-hour cost is 3,650 ÷ 120 = GH¢30.42 per hour.
Job example. Ten clamp sets (pad and handle), 0.5 hours each of machine time: 5 hours × 30.42 = GH¢152.10; bar material example GH¢120; cost GH¢272.10. A 30% mark-up on cost gives a price of GH¢353.73 (profit GH¢81.63; margin 23.1% of the price). Margin is profit ÷ price; mark-up is profit ÷ cost, so do not mix them up.
Small business ideas and ingenuity
- Make and sell bench clamps, replacement handles and pads.
- Stock common bushes and pins for local vehicle and farm machinery.
- Offer a repair-while-you-wait service for threaded parts.
- Sell machined parts to fabricators who have no lathe.
- Teach the lathe to apprentices and charge a fee (register trainees: see the STMA note below).
Market yourself
Keep a portfolio of photos of your parts with sizes. Use a WhatsApp Business profile with your catalogue and prices (marked as examples until you set your own), a Google Business Profile for your shop, clear signage, and ask for referrals from fabricators and mechanics. Quote in writing with a deposit.
Registering and permits
- Business name (sole proprietor) at the Office of the Registrar of Companies (ORC): GH¢130 in 2026. Your Ghana Card number is your tax number.
- Assembly permit. In Sekondi-Takoradi, a metal fabricator paid GH¢200 a year under the 2025 fee resolution; a different fee may apply to a machine shop: ask the Assembly. The STMA says master artisans must register all trainees.
- Fire certificate, Factories Inspectorate, EPA: not verified for small machine shops: ask the Ghana National Fire Service, the Department of Factories Inspectorate and the EPA. See Basic Welding Level 3 and this course's Level 3 Unit 6.
Accessibility
The Persons with Disability Act 2006 bans job discrimination. Drawing, quoting, inspection, programming and customer care are desk work suitable for many wheelchair users; a machine with a seated, ramp-level workstation or an adjustable bench can suit some workers. Deaf workers need visual signals and written permits; blind workers should not operate machines. Ask a qualified occupational therapist or safety officer about adjustments. The share of the Assemblies' disability fund is not verified: ask the Assembly.
Cost a job
- Work out a machine-hour cost using your own example figures.
- Cost the pad-and-handle job for 10 and for 50 sets.
- Write a one-page quote with price, deposit and delivery date.
- Plan your first month of marketing.
Check the money
Using the example costs, find the price of 50 sets at a 30% mark-up if each set uses 0.5 hours of machine time and GH¢12 of material.
Visit a shop
Visit one machine shop or vehicle parts shop. Note what they make or sell, ask one question about the work and write what you learned. Do not give out phone numbers.
Check yourself
- What is margin, and what is mark-up?
- Name two ways to find customers.
- Who do you ask about a business permit?
Appendix A · Tools and Items Glossary
Note on names. Local names for machines and tools differ from town to town, and many have none. Use the standard name in this book and show the picture or the tool when you ask for it. The "Also called" column gives other common English or trade names.
| Item | What it is and what it does | Typical size or type | Also called |
|---|---|---|---|
| Anvil (micrometer) | The fixed measuring face | — | |
| Apron | The part of the carriage below the saddle holding the feed controls | — | |
| Bed | The base of the lathe with slideways | — | |
| Bench grinder | Grinds tools | 150 to 200 mm | — |
| Boring bar | Holds a tool to enlarge a hole (L2) | — | |
| Carriage | Slides along the bed | — | |
| Centre drill | Starts a drill | No. 2 | — |
| Chuck, three-jaw | Self-centring work holder | 125 to 200 mm | — |
| Chuck, four-jaw | Independent work holder | 160 to 250 mm | — |
| Chuck key | Tightens the chuck | — | |
| Compound rest | Swivelling slide on the cross-slide | — | |
| Cross-slide | Moves the tool in and out | — | |
| Cutting oil | Coolant and lubricant | — | |
| Digital caliper | Caliper with display | 0 to 150 mm | — |
| Drill chuck | Holds drills | 0 to 13 mm | — |
| Engineer's square | Right-angle checker | 100 to 150 mm | — |
| Facing tool | Cuts the end of the bar | — | |
| Feed rod | Powers the carriage | — | |
| File | Hand file | 200 mm | — |
| Headstock | Holds the spindle | — | |
| HSS tool bit | High-speed steel cutting tool | 8 to 12 mm | — |
| Isolator | Main power switch | Main switch | |
| Lead screw | Threaded rod for screw cutting | — | |
| Micrometer | Precise outside measuring | 0 to 25 mm | — |
| Parting tool | Cuts the finished part off | 2 to 3 mm | — |
| Safety glasses | Eye protection | — | |
| Scriber | Marks lines | — | |
| Spindle | Rotating shaft | — | |
| Steel rule | Measuring rule | 150, 300 mm | — |
| Swarf | Metal chips from cutting | — | |
| Tailstock | Supports work or holds a drill | — | |
| Tool post | Holds the tool | — | |
| Twist drill | Drill bit | 3 to 16 mm | — |
| Vernier caliper | Caliper with vernier scale | 0 to 150 mm | — |
Appendix B · Quick cards
Quick card 1: speed
- RPM = 1000 × m/min ÷ (π × mm).
- HSS starting cutting speeds: mild steel 20 to 25, brass 60 to 100, aluminium 100 to 150 m/min, cast iron about 15 (beginner-low values; the ranges from the source are wider).
- Drill at the same surface speed with the drill's diameter.
Quick card 2: before you start
- Glasses on. No gloves. Hair tied. Key out. Guard in place. Tool at centre height. Work gripped. Speed set. Hand on stop.
Quick card 3: measure
- Clean the faces. Check the zero. Stop the machine. Light pressure. Read twice. Write it down.
Appendix C · Blank forms
Set-up sheet. Date: ____ Part: ____ Material: ____ Bar size: ____ Chuck: ____ Tool(s): ____ Speed: ____ Feed: ____ Coolant: ____ Checked by: ____
Daily lathe check. Date ____ Machine ____ Oil level ____ Guard ____ Stop button ____ Belts ____ Slides smooth ____ Noise ____ Swarf cleared ____ Signed ____
Job card. Customer ____ Job ____ Material ____ Hours ____ Deposit ____ Balance ____ Delivery date ____
Appendix D · Index
Anvil: Unit 4. Bed: Unit 2. Bench grinder: Unit 3. Caliper: Unit 4. Centre height: Unit 3. Chuck: Unit 3. Chuck key: Unit 1. Cutting speed: Unit 2. Drilling: Unit 5. Facing: Unit 5. General tolerance: Unit 4. Guards: Unit 1. Machine-hour cost: Unit 7. Micrometer: Unit 4. Parting: Unit 5. Process sheet: Unit 6. Swarf: Unit 1. Tailstock: Unit 2. Tool angles: Unit 3. Turning: Unit 5.
Glossary
| Term | Meaning |
|---|---|
| Bed | The base of the lathe |
| Chamfer | A small slope cut on an edge |
| Chatter | Vibration that leaves a wavy surface |
| Chuck | The jaws that hold the work |
| Competent / Not Yet Competent | The two possible results of a CBT assessment |
| Cutting speed | Surface speed of the work past the tool in m/min |
| Depth of cut | Radius of metal removed in one pass |
| Facing | Cutting the end of the work flat |
| Feed | Movement of the tool per turn of the work |
| Swarf | Metal chips and ribbons |
| Turning | Cutting the diameter of the work |
| Vernier | A sliding scale that gives fine readings |
Logbook
Copy these pages into an exercise book. Your logbook is part of your assessment evidence.
- Unit 1: safety walk-round; daily check sheets
- Unit 2: labelled lathe; speed card; daily care
- Unit 3: set-up sheet; tool angles
- Unit 4: caliper and micrometer readings; drawing notes
- Unit 5: stepped pin; fault diary
- Unit 6: process sheets; inspection records; the pad and handle
- Unit 7: costed quote; marketing plan
- Every homework, dated
Self-check quiz
- Name three things you must not wear at a lathe.
- What must you do with the chuck key?
- What does the cross-slide do?
- Write the formula for spindle speed.
- Give the RPM for 25 mm mild steel at 25 m/min.
- Where must the tool tip be?
- When do you use a four-jaw chuck?
- What does a general tolerance note mean?
- How do you check a caliper before use?
- What is the depth of cut for reducing 30 mm to 28 mm?
- Why use a low speed for parting off?
- Define margin and mark-up.
Further reading and sources
Best next reads: your machine's manual; this course's Level 2; the Hub's Basic Welding and Fabrication.
What this module does not cover: threading, tapers, boring, milling and fits (Level 2); jigs, CNC and complete assembly (Level 3); welding (see Basic Welding and Fabrication); Ghana prices for machines and bar (not found reliably; all prices are examples); any Ghana standard for lathe practice (none found; international values are labelled).
Every source used in this manual is listed, with links, in the Teacher Copy.