About this module
At Level 1 you learned to look after an engine that works. At Level 2 you learn to find out why one does not. The method is simple: an engine needs spark, fuel, air and compression at the right time. If it will not run, one of them is missing. Test them one at a time, and do not guess.
Who it is for. Trainees who have finished Level 1, or who have equal experience (the trainer may check). Level 2 is for people who do routine and some varied tasks under limited supervision. Trainees must be 18 or over for hazardous work.
No official CTVET unit list was found for small engines. This module is not a CTVET curriculum. Ask CTVET or the regional Ghana TVET Service office whether a standard exists.
Bridge from Level 1: what you already know
- Fuel, fire and exhaust safety: petrol outdoors, containers on the ground, never run an engine in a closed space
- The four strokes, and how a two-stroke differs
- Mixing two-stroke fuel by the maker's ratio, checking and changing oil
- The daily checklist, starting, cleaning an air filter and inspecting a spark plug
- Setting up and priming a centrifugal pump
- Basic care of tillers and a chainsaw, with the engine off
- Costing a job and the first registration steps
How the module works
Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent by being watched at work, by your tasks, by answering questions, and by your logbook. Every unit ends with homework and a short Check yourself.
Golden rule of this module. Use your engine's manual for every figure: plug gap, valve clearance, compression, oil grade and torque differ by engine. Appendix B1 prints the typical figures that Honda gives for the engines in its WB20XT and WB30XT pumps, and says where sources disagree. They are typical for those engines, not universal. Where no open source was found, the table says so and sends you to the shop manual. Never carry a number from one engine to another.
Unit 1 · Ignition: find a spark fault
No spark, no start. But a good spark at the wrong time, or a weak spark, causes trouble too. Test, do not guess.
Competency standard
| Learning outcome | Performance criteria: the trainee… |
|---|---|
| 1.1 Explain the ignition system | names plug, cap, lead, coil, flywheel magnet and stop switch and their jobs |
| 1.2 Test for spark safely | uses an inline spark tester and avoids shock |
| 1.3 Read and replace plugs | reads plug deposits; fits the correct plug at the manual's gap |
| 1.4 Find simple ignition faults | tests plug, cap, kill switch and coil in order |
Range. Small air-cooled petrol engines with a magneto or coil ignition. Evidence. Fault-finding on a set-up engine; oral questions.
Ask a qualified expert. For fuel, fire, electrical or other dangerous work, ask a qualified mechanic, an Energy Commission-certified electrician or a GhIE-registered engineer. An ignition coil makes a high-voltage spark: never hold the plug lead or the plug in your bare hand while the engine is turned over. Do not test for spark near fuel, spilt petrol or open containers. Do not attempt work you are not trained and authorised to do.
How the spark is made
A spinning magnet in the flywheel passes the coil, which makes a pulse of high voltage. The pulse goes through the plug cap and lead to the spark plug, which jumps a small gap. The stop switch shorts the coil to stop the engine. If any link is damaged, no spark.
Read the plug
A light brownish tip suggests good running. Deposits on the nose suggest a plug that is too cold, porous sugar-like porcelain suggests too hot, and oil leaking into the chamber fouls the tip. A tip that is too hot can cause pre-ignition or knock, and one that is too cold can collect conductive deposits that weaken or short the spark. Brands number heat ranges differently, so a plug number from one brand cannot just be swapped for another. Always fit the plug type in the manual.
| Plug look | Likely meaning | What to check |
|---|---|---|
| Light brown or grey | Healthy | Nothing |
| Black, dry, sooty | Rich mix, dirty filter, too much choke | Air filter, choke, carburettor |
| Black, wet, oily | Too much oil, or oil entering the cylinder | Oil level, mix ratio, rings (Unit 3) |
| White, blistered | Lean mix or overheating | Air leaks, fuel flow, cooling fins |
| Cracked, burnt electrode | Worn out or wrong type | Replace |
Replacing a cheap plug is often better than cleaning it, and a wire brush can leave metal traces that weaken the spark. Do not bend the electrode of an iridium or platinum plug.
Spark test (safe method)
- Engine off. Fuel tap off. Clean dirt from around the plug.
- Remove the plug. Fit it into the inline spark tester or its cap, and ground the metal body against the engine. Keep your hands off the metal and the lead.
- Keep fuel and fumes away. Do it in open air, away from the fuel container and any spill.
- Pull the starter briskly. Look for a bright blue spark in the tester.
- No spark, or a weak red-orange spark: continue fault-finding.
The order of tests
- Stop switch. Is the kill wire grounded or stuck? Disconnect it and test again.
- Plug. Swap in a known-good plug of the correct type.
- Cap and lead. Cracked, wet or corroded: replace.
- Coil and flywheel. If there is still no spark, a worn coil, a damaged flywheel key or a wrong air gap between coil and magnet may be the cause. Setting the coil gap and testing a coil need the manual and a qualified mechanic. Do not hammer, pry or heat a flywheel.
Do not run a test by sparking against the carburettor or fuel parts, and do not test spark in a closed room. Use the inline tester in open air. Never rely on your hand to feel the spark: it can hurt and it is not a test.
Fault tree
A pump engine starts easily when cold but dies after five minutes and will not restart until it cools. The plug looks normal. List three possible causes of ignition and two causes of fuel or air.
Photo: parts you can see
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Threaded shell | Screws into the cylinder head | Fit by hand first so you do not cross the thread; never over-tighten |
| 2 | White insulator | Keeps the high voltage inside the plug | A cracked insulator can leak the spark: replace the plug |
| 3 | Centre electrode | Carries the voltage to the gap | Do not bend it |
| 4 | Side (ground) electrode | The second side of the gap | Set the gap only with a feeler gauge to the maker's figure |
| 5 | Spark | Jumps across the gap and lights the mixture | Never test a spark with a bare hand or near fuel vapour; use an inline spark tester |
Parts and safety rules
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Flywheel | Heavy wheel with magnets; its spin makes the coil produce a spark | Never touch it while the engine can turn |
| 2 | Flywheel key | Small key locking the flywheel to the shaft | A sheared key upsets timing: refer |
| 3 | Coil air gap | Gap between the coil and the flywheel magnets | Set only to the maker's figure |
| 4 | Ignition coil | Makes the high voltage | Carries high voltage: do not touch the lead while cranking |
| 5 | Plug lead | Carries the voltage to the plug | Look for cracks and burn marks; replace if damaged |
| 6 | Plug cap | Connects the lead to the plug | Pull by the cap, not the wire |
| 7 | Spark plug | Makes the spark in the cylinder | Never test with a bare hand; keep away from fuel vapour |
| 8 | Stop-switch lead | Carries the earth signal that stops the engine | A shorted lead gives no spark |
| 9 | Stop (kill) switch | Earths the ignition to stop the engine | Test that it stops the engine |
| 10 | Inline spark tester | Shows spark safely in the plug lead | Fit it before cranking; keep it away from spilled fuel |
| 11 | Crankshaft end and flywheel nut | Hold the flywheel on | Torque to the shop-manual figure |
SAFETY PROTOCOL: Spark test
Before you start
- Engine off; plug cap pulled; no spilled fuel or fuel smell nearby; fuel tap closed.
- Inline tester fitted; area dry; PPE: gloves and glasses.
- Hold the lead by its insulated cap only.
While you work
- Do: crank with the starter and watch the tester gap.
- Do not: hold the plug or the metal part of the lead; test near fuel vapour; test in a closed room.
After you finish
- Refit the plug and cap; stop switch tested; log the result.
- Report cracked leads or a failed stop switch.
Emergency
- Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
- Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
- Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
- Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
Tools and items for this unit
| Item | What it is and when you use it | Size or type |
|---|---|---|
| Inline spark tester | Shows spark safely; never test with a bare hand | Fits the plug cap |
| Feeler gauge and plug spanner | Plug gap and removal | Gap from the manual |
| Multimeter | Resistance of the coil, if the maker gives a figure | Basic digital |
| Tachometer | Idle speed check | Optical or clip-on |
Defined in full in Level 1 Appendix A12 and Appendix B13 below.
Ignition fault-finding
- Remove, read and photograph the plug from a trainer-set engine. Write what it tells you.
- Check the plug gap with a feeler gauge against the manual figure. Fit a new correct plug.
- Do the inline spark test in open air. Record the spark colour.
- Test in the order: stop switch, plug, cap and lead. Record each step.
- The trainer swaps in a fault. Find it using only the test order.
- Write a short fault report: symptom, test, finding, fix.
Plug collection
Ask a mechanic if you may look at used plugs from different engines. Sketch three and say what each tells you about the engine.
Check yourself
- Why must you not hold the plug lead while turning the engine over?
- What colour is a healthy plug tip?
- Name the four parts to test in order when there is no spark.
Unit 2 · The fuel system and the carburettor
Most small-engine faults are fuel faults, and most fuel faults are dirt, old fuel or blocked jets.
Competency standard
| Learning outcome | Performance criteria: the trainee… |
|---|---|
| 2.1 Explain the fuel path | traces tank, tap, filter, carburettor, engine; names tank vent and float |
| 2.2 Find fuel faults | tests flow, filter, vent and carburettor in order |
| 2.3 Clean a carburettor | removes, strips, cleans, refits and records |
| 2.4 Start and tune simply | sets idle as the manual says; does not adjust governor |
Range. Float-type carburettors on four-stroke engines; diaphragm type on two-stroke saws (overview). Evidence. Carburettor service; oral questions.
Ask a qualified expert. For fuel, fire, exhaust or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. Work with fuel only outdoors, engine cold, no flame nearby, with a tray under the carburettor and a rag. Never wash parts with petrol near a flame. Do not attempt work you are not trained and authorised to do.
How a carburettor works
Air rushes through a narrow section (the venturi); the faster air lowers the pressure and pulls fuel from the jets into the air stream, while a throttle plate controls how much air enters. The main jet feeds fuel in normal running, the idle jet feeds a small fixed amount at low speed, and an off-idle circuit smooths the change as the throttle opens. A float bowl keeps a steady fuel level through a float valve. Engines that must work at any angle, such as chainsaws, use diaphragm chambers instead of a float bowl. The choke partly closes the air entrance for a cold start; left closed when warm it makes the mixture too rich, causing rough running, lost power and high fuel use. Flooding stops an engine starting; holding the throttle open while pulling can help clear it.
Fault-finding order for "will not start" or "runs badly"
- Fuel in the tank? Tap open? Tank vent open? A blocked vent stops fuel flowing as the tank empties.
- Fuel reaches the carburettor? Loosen the bowl drain screw or the fuel line into a tray: clean fuel should flow. If not, check the tap, filter and line.
- Air filter clean? A blocked filter makes the engine rich.
- Choke and throttle moving freely and set correctly.
- Carburettor dirty? Gum from old fuel blocks small jets. Signs: starts then dies, rough idle, surges, needs choke to stay running.
- Only then consider spark (Unit 1) and compression (Unit 3).
Stale fuel. Old petrol goes stale. One manufacturer advises using mixed fuel within 30 days, or 60 days with a stabiliser. Drain stale fuel into a container and take it out of the engine.
Cleaning a float carburettor (step by step)
- Engine off, cold, outdoors. Close the fuel tap. Put a tray and rags below.
- Take a photo of the carburettor, linkage and springs before you remove anything. Draw the layout in your logbook.
- Remove the air-filter housing and disconnect the fuel line, choke and throttle linkage.
- Remove the carburettor. Keep every screw and spring in a labelled dish.
- Remove the float bowl and drain it. Look for dirt, water and white corrosion.
- Lift out the float, needle valve and the main jet. Note the order.
- Clean the jets with carburettor cleaner and compressed air or clean fine wire (only the soft wire made for it). Never enlarge a jet with a drill bit. A bigger hole upsets the mixture for ever.
- Check the float needle: a worn needle leaks fuel into the bowl. Replace worn parts with the correct kit.
- Check the float moves freely and the height is as the manual says (do not bend the float tab unless the manual explains).
- Refit in the reverse order, with a new gasket if needed. Reconnect linkage as in your photo.
- Refit, open the fuel tap, look for leaks, then start the engine in open air.
- Set the idle as the manual says. Do not adjust the governor or high-speed stop.
Do not soak rubber and plastic parts in strong cleaner. Read the cleaner's label. If a part is cracked, hard or swollen, replace it. Dispose of dirty cleaner and fuel safely, not on the ground.
Fuel cost and stale fuel
Example figures. A farmer mixed 20 litres of two-stroke fuel on 1 November and used 4 litres a week. The maker advises using mixed fuel within 30 days with no stabiliser. (a) By what date has the farmer used 20 litres? (b) How much fuel is left on day 30? (c) What should be done with it?
Parts and safety rules
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Air inlet | Where air enters from the filter | Never leave open: dust damages the engine |
| 2 | Choke plate | Enriches the mix for a cold start | A stuck choke gives black smoke |
| 3 | Venturi | Narrow throat that speeds the air to draw fuel | Do not damage the surface |
| 4 | Throttle plate | Sets airflow and speed | Do not force it |
| 5 | Idle jet (pilot jet) | Meters fuel at idle | Clean with soft wire; never drill |
| 6 | Idle screw | Sets idle speed | Adjust only as the manual says |
| 7 | Float | Rides on the fuel and shuts the needle | Handle gently; a leaking float floods the engine |
| 8 | Needle valve | Opens and shuts the fuel inlet | Replace if worn or ridged |
| 9 | Fuel inlet | Fuel arrives here from the tap and filter | Fuel leak here is a fire risk |
| 10 | Float bowl | Holds a small reserve of fuel | Catch the fuel in a tray when you remove it |
| 11 | Drain screw | Empties the bowl | Drain outdoors into a container |
| 12 | Main jet | Meters fuel at high speed | Never enlarge it |
SAFETY PROTOCOL: Cleaning a carburettor
Before you start
- Engine off and cold; fuel tap closed; no flames; outdoors; photograph the parts first.
- Clean tray, carburettor cleaner or clean petrol, soft wire, compressed air with eye protection.
- PPE: glasses and gloves.
While you work
- Do: keep parts in order; wash and blow clear; check the float and needle.
- Do not: drill or enlarge a jet; soak rubber or plastic in cleaner; use cleaner near a flame.
After you finish
- Refit with new gaskets from a kit; check for leaks; dry before starting.
- Dispose of old fuel and cleaner properly; log the job.
Emergency
- Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
- Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
- Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
- Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
Tools and items for this unit
| Item | What it is and when you use it | Size or type |
|---|---|---|
| Carburettor cleaner or clean petrol | Washes gum from parts; fire risk; keep rubber and plastic out | Can |
| Jet cleaning set | Clears a jet without enlarging it | Fine wire |
| Compressed air with eye protection | Blows passages clear | Small compressor |
| Carburettor kit | Gasket, needle, float, jets for the model | By model |
| Clean tray and camera or phone | Keep parts in order; photograph before stripping | Any |
Defined in full in Level 1 Appendix A12 and Appendix B13 below.
Strip and clean a carburettor
- On a trainer-prepared engine with a gummed carburettor, follow the 12 steps. Photograph before and after.
- Record each part removed and each cleaning step.
- Refit, start in open air, set idle as the manual says, and run 5 minutes.
- Check for leaks and note any fault left.
- Write a one-page service note for the owner: fault found, work done, advice on fuel.
Fuel questions
Ask two farmers how long they keep petrol in a drum or jerrycan, and whether they have had trouble from old fuel. Write down their stories.
Check yourself
- What does the choke do?
- Why must you never enlarge a jet with a drill bit?
- Name two signs of a dirty carburettor.
Unit 3 · Compression and the top end
You can have fuel and spark, and still no power if the cylinder cannot hold pressure. Learn to test, then learn when to stop and ask.
Competency standard
| Learning outcome | Performance criteria: the trainee… |
|---|---|
| 3.1 Explain compression | says why the cylinder must seal; names rings, valves and head gasket |
| 3.2 Do a compression test | tests safely; compares with the manual |
| 3.3 Interpret the result | says whether rings, valves or gasket are likely; decides repair or referral |
| 3.4 Adjust valve clearance only if allowed | follows the manual; records; refers if unsure |
Range. Four-stroke pump engines; two-stroke diagnosis overview. Evidence. Compression test report; oral questions.
Ask a qualified expert. For fuel, fire, exhaust, pressure or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. Opening the cylinder head or crankcase is rebuild work: do not do it at this level without a qualified mechanic present. Do not attempt work you are not trained and authorised to do.
Why compression matters
In a four-stroke the piston squeezes the mix before the spark; squeezing improves efficiency. If the rings, the valves or the head gasket leak, the squeeze is lost and the engine is weak, hard to start, smoky or uses oil.
Compression test (basic method)
The exact method and the correct reading are in your engine's manual. A typical order:
- Run the engine briefly, then stop it, so it is warm, not hot. Let the silencer cool.
- Remove the plug (see Unit 1) and keep the plug cap away from the hole.
- Screw or hold the compression gauge firmly in the plug hole.
- Open the throttle fully (as the manual says) and pull the starter several times (or turn with the starter) until the needle stops rising.
- Write the reading. Repeat once more. Compare with the manual figure.
- Wet test: squirt about a teaspoon of clean engine oil into the plug hole and test again. If compression rises, worn rings are likely, as the oil briefly seals the gap. If it stays the same, a valve or head gasket leak is more likely. This method is only moderately accurate.
What the result may mean
| Reading | Likely cause | Next step |
|---|---|---|
| Normal (as the manual) | Compression is not the problem | Go back to fuel and spark |
| Low, rises with oil | Worn rings or cylinder | Quote for rebuild; refer if beyond your skill |
| Low, does not rise with oil | Valve or head gasket leak | Check valve clearance; refer |
| Zero | Broken part, stuck valve | Stop; refer |
A leak-down test shows where the air escapes: air heard at the dipstick or breather points to rings, at the carburettor to an intake valve, at the silencer to an exhaust valve. This needs a tester and the manual.
Valve clearance
The small gap between the valve stem and its pusher or rocker must be correct so the valve closes fully. Too little clearance can stop valves sealing and overheat exhaust valves. Your engine's manual gives the figure and the steps. If you are not sure, do not guess; ask a qualified mechanic.
Two-stroke notes
On a two-stroke chainsaw or tiller, low compression often comes from worn rings, a scored cylinder or leaking crankcase seals. Crankcase seal leaks cause hard starting and a lean mix. This is workshop work for a qualified mechanic at this level.
When to stop and refer
Refer when: the test shows low compression and the owner wants a rebuild; metal particles are in the oil; the engine knocks; or the cost of repair approaches the price of a new engine (Level 3 teaches repair-or-replace costing).
Reading the result
Engine A reads low. After a teaspoon of oil in the plug hole the reading rises well. Engine B reads low and does not change. (a) What is likely wrong with each? (b) Which may be cheaper to fix? (c) What do you tell the owner?
Parts and safety rules
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Gauge | Shows cylinder pressure | Write the unit (psi, kPa or bar) |
| 2 | Gauge hose | Connects the gauge to the adapter | Check for cracks |
| 3 | Adapter | Threads into the plug hole | Thread must fit; do not cross-thread the head |
| 4 | Spark plug hole | The opening in the head | Keep dirt out |
| 5 | Piston | Squeezes the mix | Never put a finger in the hole |
| 6 | Cylinder and piston rings | Seal the piston | Worn rings lower the reading |
| 7 | Intake valve | Lets the mix in | Leaks lower the reading |
| 8 | Exhaust valve | Lets the gas out | Leaks lower the reading |
SAFETY PROTOCOL: Compression test
Before you start
- Engine warm, not hot; silencer cooled; plug cap away from the hole; no fuel leak.
- Gauge and adapter checked; PPE: glasses, gloves.
- Fuel tap closed; stop switch earthed so no spark.
While you work
- Do: open the throttle, crank until the needle stops, write the reading twice.
- Do not: crank with the plug out and the cap near the hole; put fingers over the hole; run the engine.
After you finish
- Refit the plug and cap; release the gauge pressure; log the readings.
- Refer low or zero readings (Unit 3).
Emergency
- Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
- Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
- Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
- Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
Tools and items for this unit
| Item | What it is and when you use it | Size or type |
|---|---|---|
| Compression tester | Reads cylinder pressure | Thread must fit the plug hole |
| Leak-down tester | Shows where air escapes | Needs a compressor |
| Feeler gauge | Valve clearance with the maker's figure | Blades in mm |
| Torque wrench | Tightens to the shop-manual figure | N.m or ft.lb |
| Teaspoon of clean oil | Wet test | Clean engine oil |
Defined in full in Level 1 Appendix A12 and Appendix B13 below.
Compression test
- On two trainer engines (one good, one worn), warm the engine briefly and stop it.
- Follow the six steps. Record both readings and the manual's figure.
- Do the wet test on each. Record the change.
- Say, from the table, what each engine's problem probably is.
- Write a one-paragraph note to the owner, in plain language.
Ask a rebuilder
Ask an experienced engine mechanic how they decide whether to rebuild or replace a small engine. Write three things they look for.
Check yourself
- Name three parts that can leak compression.
- What does the wet test show?
- When should you stop and refer?
Unit 4 · Pump performance: head, flow and choosing a pump
A farmer asks, "Which pump should I buy?" You must answer with sums, not guesses. Two numbers matter: how high the pump must push (head), and how much water it must move (flow).
Competency standard
| Learning outcome | Performance criteria: the trainee… |
|---|---|
| 4.1 Explain head and flow | defines suction lift, delivery head, friction loss, total head and flow |
| 4.2 Calculate total head | adds lift, height and friction loss for a layout |
| 4.3 Match a pump to a job | compares the job with the pump's rated head and flow |
| 4.4 Prevent cavitation and damage | sets suction short and low; avoids dry running |
Range. Small centrifugal pumps; hoses up to a few tens of metres; surface water or tanks. Evidence. Head and flow worksheet; set-up on the practice site.
Ask a qualified expert. For pressure, lifting, fuel, fire or electrical work, ask a qualified mechanic or a GhIE-registered engineer. Never connect a pump to an existing pressurised pipe, tank or borehole without a qualified plumber or engineer. Ask a GhIE-registered engineer for any large pump or high-pressure system. Do not attempt work you are not trained and authorised to do.
Head: how high the pump must push
Head is a height of water, in metres. It stands for energy: the higher the water must go, the more energy it needs. Moving water also loses energy to friction in pipes, bends, valves and fittings; this is head loss. In short pipe runs with many fittings, the fitting losses can exceed the pipe losses.
For a pump set:
- Suction lift: height from the water surface up to the pump.
- Delivery head: height from the pump up to the end of the delivery hose (or the sprinkler).
- Friction loss: the loss in hoses, bends and fittings; it grows with longer, thinner hoses and with faster flow.
- Total head = suction lift + delivery head + friction loss (plus the pressure needed at a sprinkler, if used; see the sprinkler maker).
Each pump maker publishes a performance curve: how much flow the pump gives at each total head. The farmer's job must fall inside the curve with a good margin.
Flow: how much water
Flow is the volume per minute or per hour (litres per minute, or cubic metres per hour). To water a bed you need: the amount of water and the time you have. Time = water needed ÷ flow.
The suction limit
A pump does not really suck water. Air pressure on the water surface pushes it toward the pump. This gives a limit: at sea level atmospheric pressure is about 10 metres of head, and the suction lift, friction on the suction side, and the pump's own requirement all use part of that. In practice a surface pump should be placed as close to the water and as low as possible, with a short, straight, airtight suction. Cavitation happens when the pressure at the impeller inlet falls too low; bubbles form and collapse, causing noise, vibration and erosion of the impeller. Hot water makes it worse. If the pump rattles or the flow collapses, shorten the suction, lower the pump or use a wider hose. Do not just open the throttle more.
Choosing a pump (steps)
- Find the water need (litres per bed or per hour, and the time available).
- Measure the layout: suction lift, height to the field, hose length.
- Add friction loss (use the hose maker's table, or the example table in Appendix B5, recalculated from the Hazen-Williams formula; ask the dealer or a qualified engineer to confirm; Level 3 goes deeper).
- Add up total head.
- Choose a pump whose curve gives the needed flow at more than the total head, with a margin.
- Confirm the engine power, fuel use and the maker's advice. Ask the dealer for the curve in writing.
- Check whether you need permission to take water. See the Level 1 note in Unit 5.
Total head and watering time
Example figures (not a real pump). Water level to pump: 2 m. Pump to the field outlet: 10 m higher. Friction loss: 3 m. The pump's published curve gives 300 litres a minute at 20 m total head. A bed needs 9,000 litres. (a) What is the total head? (b) Is the pump suitable at 20 m? (c) How many minutes to fill the bed's water need? (d) If the pump burns 1.2 litres of petrol an hour at an example GH¢15 a litre, what is the fuel cost for this one watering?
Do not trust a pump's "maximum lift" or "maximum head" alone. The maker's numbers are for the best case. Real jobs lose head to friction and use up part of the suction limit. Always leave a margin and use the curve.
Parts and safety rules
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Water surface | The level the lift is measured from | Check the bank is firm before standing near it |
| 2 | Suction lift | Height from the water to the pump | Keep as small as possible |
| 3 | Pump | Raises the water | Keep on firm level ground |
| 4 | Delivery height | Height from the pump to the outlet | Fix the hose so it cannot whip |
| 5 | Delivery hose and friction loss | Loss of head along the hose | Never kink or block it while running |
| 6 | Outlet or sprinkler pressure | Head needed at the end of the line | Never stand in front of a pressurised end |
| 7 | Suction hose and strainer | Bring the water in | Reinforced, airtight, strainer fully under water |
SAFETY PROTOCOL: Pump performance test
Before you start
- Daily engine checks; pump primed; hoses and clamps tight; delivery hose fixed.
- Measuring tools ready (tape, level, bucket, stopwatch, gauge).
- Permission to take the water checked; PPE worn.
While you work
- Do: time first water; measure flow with a bucket; record head and flow.
- Do not: run the pump dry; run against a closed delivery for long; connect to existing pressure lines without a qualified person.
After you finish
- Stop, drain, clean the strainer; coil hoses; write the results in the logbook.
- Report leaks and overheating.
Emergency
- Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
- Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
- Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
- Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
Tools and items for this unit
| Item | What it is and when you use it | Size or type |
|---|---|---|
| Tape measure and level or clear tube level | Measure suction lift and delivery height | 5 or 8 m tape |
| Pressure gauge | Pressure at the pump or sprinkler | bar, kPa or psi |
| Bucket and stopwatch | Flow test | 20 litres |
| Calculator | Friction, power and fuel sums | Any |
Defined in full in Level 1 Appendix A12 and Appendix B13 below.
Measure, calculate, choose
- On the practice site, measure the suction lift, the delivery height and the hose length with a tape and a level (or a clear tube level).
- Estimate friction loss using the dealer's or maker's chart (the trainer supplies one).
- Calculate total head and the watering time for a given volume.
- Set up the pump to match; time the first water; run the pump.
- Shorten the suction hose by half and run again. Record the effect.
- Write a short recommendation to a farmer, with the numbers.
Collect pump data
Visit a dealer and collect the head, flow and engine power for two pumps. Ask for the curve. Write the figures down, and note the prices as examples only if the dealer will not confirm them.
Check yourself
- What three things add up to total head?
- What makes cavitation more likely on the suction side?
- Why must you use the pump's curve, not just its maximum head?
Unit 5 · Small diesel engines and diesel pumps
Diesel engines have no spark plug and are tough, but they hate air and dirt in the fuel. The faults are different, and so are the dangers.
Competency standard
| Learning outcome | Performance criteria: the trainee… |
|---|---|
| 5.1 Explain diesel | says how compression ignites the fuel; contrasts with petrol |
| 5.2 Do daily checks | checks fuel, oil, filters, water in fuel, belts and coolant (if any) |
| 5.3 Bleed the fuel system | removes air from the system in the right order |
| 5.4 Know the limits | refers injector and pump work to a qualified mechanic |
Range. Small air-cooled or water-cooled diesel pump engines. Evidence. Daily checks and bleeding on a trainer engine; oral questions.
Ask a qualified expert. For fuel, fire, exhaust, pressure or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. Diesel injectors work at very high pressure, so never put a hand near a leaking injector line while the engine runs or is cranked; leave injector and injection-pump work to a qualified diesel mechanic. Diesel is a fire and pollution risk: store it as you store petrol, outdoors, closed and away from flame. Do not attempt work you are not trained and authorised to do.
How a diesel works
A diesel compresses only air, which heats up enough to ignite fuel sprayed in near the top of the stroke, so it needs no spark plug. The fuel is sprayed in at high pressure. The engine's power is controlled by how much fuel is injected, not by a throttle on the air. Diesels usually use fuel more efficiently than petrol engines. The fuel prefers a high ignition quality, not a high octane rating.
| Petrol | Diesel | |
|---|---|---|
| Ignition | Spark plug | Heat of compression |
| Fuel | Petrol | Diesel; do not mix them |
| Common faults | Spark, carburettor | Air in the fuel, dirty fuel, blocked filter |
| Danger | Vapour fire | High-pressure spray, fire, heavy parts |
Never put petrol in a diesel, or diesel in a petrol engine. Label every container.
Daily checks (engine off)
- Fuel level and no leaks; clean fuel.
- Engine oil level on the dipstick.
- Water in the fuel: drain the sediment bowl or separator as the manual says.
- Air filter clean.
- Cooling: air fins clean, or coolant level for water-cooled engines (cold engine only).
- Belts, guards, mounting bolts tight.
- Pump hoses, strainer and clamps (Level 1 and Unit 4).
Bleeding air from a small diesel fuel system
Air in the fuel lines can act as a lock and stop fuel reaching the cylinder, which can happen when you change a filter, run out of fuel or disturb the fuel system. A common method works from the tank toward the injectors, and most small equipment has a hand priming lever. Pumping until the plunger feels firm is a sign that fuel is reaching the filter. If it still will not start, air may be trapped between the injection pump and the injectors, which a qualified diesel mechanic bleeds. Air can re-enter if the leak source is not fixed, so check seals and fittings, and fill new filters with clean diesel first. The exact bleed points are in your engine's manual.
Typical order (check your manual):
- Fuel in the tank; fuel tap open. Engine off and cold.
- Open the bleed screw on the filter nearest the tank.
- Work the hand primer until fuel without bubbles comes out; close the screw.
- Continue to the next bleed point as the manual says.
- Try starting for short periods. If it does not start after repeated tries, stop: a qualified diesel mechanic must bleed the injection side.
Typical diesel faults
| Sign | Likely cause | Check |
|---|---|---|
| Will not start, turns over | Air in fuel; empty tank; blocked filter; water | Fuel level; bleed; filter |
| Starts then dies | Blocked filter; air leak; fuel vent | Filters; fittings; vent |
| Black smoke | Blocked air filter; overloaded; worn injector | Filter; load; refer |
| White smoke | Water in fuel; cold | Drain water; warm up |
| Hard to turn | Low oil; seized parts | Stop; refer |
Fuel cost: petrol versus diesel
Example figures. A petrol pump engine burns 1.2 litres an hour and a diesel pump of the same output burns 0.9 litres an hour. Example prices: petrol GH¢15 and diesel GH¢16 a litre. For 6 hours of pumping, find the fuel cost of each and the difference.
Parts and safety rules
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Fuel tank | Holds diesel | Refuel cool, outdoors, with no flame |
| 2 | Fuel tap | Opens and shuts the flow | Close it when working on the fuel system |
| 3 | Primary filter | Stops dirt | Replace as the manual says; catch spilled fuel |
| 4 | Water bowl | Where water settles | Drain into a container; check each day |
| 5 | Second filter | Fine filter before the pump | Fit the right filter |
| 6 | Bleed screw | Lets air out of the lines | Open only as the manual says; catch the fuel |
| 7 | Injection pump | Times and meters the fuel | Refer all work on it |
| 8 | High-pressure line | Carries fuel at very high pressure to the injector | Never loosen it with the engine running; fine sprays can pierce skin: see a doctor |
| 9 | Injector | Sprays fuel into the cylinder | Refer testing to a qualified diesel mechanic |
| 10 | Fuel return line | Returns extra fuel to the tank | Check for leaks |
| 11 | Hand primer | Pumps fuel by hand to fill the lines | Use only with the engine off |
SAFETY PROTOCOL: Bleeding a small diesel
Before you start
- Engine off and cold; tap open; no flames; containers and rags to catch fuel.
- Manual open at the bleeding page; PPE: gloves and glasses.
While you work
- Do: work from the tank toward the injectors; work the primer until fuel runs without bubbles.
- Do not: loosen high-pressure lines with the engine running; ignore a fuel leak.
After you finish
- Wipe spilled fuel; check for leaks; run 5 minutes in the open; dispose of fuel-soaked rags safely.
- Refer if it still will not start.
Emergency
- Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
- Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
- Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
- Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
Tools and items for this unit
| Item | What it is and when you use it | Size or type |
|---|---|---|
| Hand primer | Fills the diesel lines with fuel | On filter or pump |
| Fuel filter and water bowl | Catch dirt and water | By engine |
| Clean containers and rags | Catch diesel when bleeding | Clean |
Defined in full in Level 1 Appendix A12 and Appendix B13 below.
Diesel daily check and bleed
- Do the daily checks on a trainer diesel engine and record them.
- Drain the water bowl as the manual says; note what comes out.
- With the trainer, change or refill a fuel filter, then bleed air following your manual.
- Start in open air; run 5 minutes; check for leaks; stop.
- Write your bleeding steps in your own words.
Compare engines
Ask a farmer who uses a diesel pump why they chose it over petrol. Write the reasons and the drawbacks.
Check yourself
- How does a diesel engine ignite its fuel?
- Name two signs that air is in the fuel system.
- Who should bleed the injection side if it will not start?
Unit 6 · Tillers and chainsaws, deeper
You have looked after these machines with the engine off. Now you service them properly: gearbox, clutch, chain and bar. The cutting itself stays with trained operators.
Competency standard
| Learning outcome | Performance criteria: the trainee… |
|---|---|
| 6.1 Service a power tiller | checks and services engine, drive, gearbox oil, tines and handlebars |
| 6.2 Check a chainsaw clutch, brake and bar | checks safely with the engine off; spots wear |
| 6.3 Sharpen a chain | files cutters evenly and sets depth gauges |
| 6.4 Find and fix simple faults | uses the fault-finding order for each machine |
Range. Walk-behind petrol tiller; petrol chainsaw. Cutting timber needs separate training. Evidence. Service and sharpening tasks; oral questions.
Ask a qualified expert. For fuel, fire, exhaust, sharp-edge or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. A chainsaw can cause deadly injury. Sharpen only with the engine off, plug cap removed, and the chain held in a vice or clamp. Do not cut timber with a chainsaw at this level without a qualified trainer. For injuries, call 112 and see a doctor or nurse. Do not attempt work you are not trained and authorised to do.
Power tiller servicing
Do everything from Level 1, then:
- Gearbox oil: check the level and grade as the manual says; change at the manual's interval. Drain warm oil into a tray; take used oil to a proper place (see Level 1 Unit 3).
- Drive belt or chain: look for cracks, glazing and slack. Adjust only as the manual says.
- Clutch and dead-man lever: must disengage the drive when released. If it does not, the machine is unsafe: do not use it.
- Tines and shaft: check for bent tines, loose bolts, worn bearings and rope or wire wound on the shaft. Remove wound material only with the engine off and cold.
- Handles and mounts: no cracks; bolts tight; vibration not excessive.
- Grease points as the manual says.
How a chainsaw is built
- The chain has cutting teeth, alternate left and right, each with a depth gauge (raker) ahead of it that limits how deep the tooth bites. A raker set too high slows cutting; filed too low it raises the chance of kickback and vibration.
- A dull chain makes powdery dust instead of clean shavings and the saw vibrates.
- Bar and chain oil is separate from the fuel; low oil or the wrong oil quickly wears the bar and can seize or derail the chain, and motor oil is a poor substitute.
- A centrifugal clutch engages the chain sprocket as engine speed rises, so the chain does not move at idle; it also protects the engine if the chain stalls in wood.
- The chain brake stops the chain in milliseconds when kickback triggers it. Guidance says to test it before each use and not to use a saw whose brake fails.
- Kickback happens when a tooth at the bar tip catches wood without cutting through, throwing the bar up toward the operator.
- Protective gear in Irish guidance includes steel-toed boots, close-fitting clothing and chainsaw trousers; no equipment gives total protection.
Chainsaw servicing (engine off)
- Plug cap off, chain brake on and guard on. Clean sawdust from fins, filter and the brake area.
- Check bar oil level and that oil reaches the chain (the trainer demonstrates with the saw safely supported).
- Check the chain tension as the manual says: it should be snug, not tight, and move freely by hand with gloves on.
- Look for a worn or burred bar rail, a damaged sprocket, a cracked chain link or a loose clutch cover.
- Check the plug, fuel mix and air filter as in Units 1 and 2.
- Test the chain brake mechanism as the manual says, before returning the saw to the user.
Sharpening a chain with a hand file
- Chain held firm; saw on a stable bench or in a vice; plug cap removed; gloves on.
- Use the file size and holder the chain maker specifies. Do not guess the size.
- File each cutter at the angle marked on the chain or holder, with even strokes from inside to outside, the same number of strokes on each cutter.
- Work round the whole chain; turn the saw and do the other side.
- Check depth gauges with a gauge tool; file down only if needed, and round the front.
- Check all cutters look the same. A mixed set cuts crooked.
- Check the tension, oil the chain, and record.
Do not run an unevenly sharpened or damaged chain. It cuts crooked, vibrates and kicks. Do not use a saw with a faulty brake, a loose clutch cover or a cracked chain.
Servicing cost
Example figures. A tiller service takes 1.5 hours at GH¢40 an hour and uses gearbox oil GH¢35, plug GH¢25, air filter GH¢30 and rags and cleaner GH¢10. A chain sharpening takes 25 minutes at the same rate, with GH¢5 of consumables. Find the total cost of each and a price at a 25% margin on price.
Parts and safety rules
| No. | Part | What it does | Safety rule |
|---|---|---|---|
| 1 | Cutter (tooth) | Does the cutting | Very sharp: wear gloves |
| 2 | Depth gauge (raker) | Limits how deep the cutter bites | Too high cuts slowly; too low raises kickback risk |
| 3 | Rivet | Joins the links | Check for wear and cracks |
| 4 | Side link (tie strap) | Joins the cutters and drive links | Replace the chain if cracked |
| 5 | Drive link | Fits the sprocket and bar groove | Check for damage |
| 6 | Bar groove | The track the drive links ride in | Clean it; a burred rail damages the chain |
| 7 | Pitch | The size of the chain | File size depends on it: see Appendix B7 |
SAFETY PROTOCOL: Sharpening a saw chain and servicing a tiller
Before you start
- Engine off, cold; plug cap removed; chain brake on; saw clamped in a vice.
- Correct file, holder and depth-gauge tool; PPE: cut-resistant gloves, glasses, boots.
- For a tiller: engine off, tines stopped, plug cap removed.
While you work
- Do: file each cutter the same number of strokes and the same angle; file the depth gauges only if needed.
- Do not: sharpen a running saw; test the chain with a bare finger; use an unevenly sharpened chain.
After you finish
- Check tension, oil the chain, test the brake as the manual says; clean up filings; log the job.
- Do not return a saw with a faulty brake or a tiller whose dead-man lever does not release.
Emergency
- Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
- Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
- Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
- Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
- Heavy bleeding: press with a clean cloth and call 112.
Tools and items for this unit
| Item | What it is and when you use it | Size or type |
|---|---|---|
| Round file, holder and depth-gauge tool | Sharpen cutters evenly and set the rakers | File by pitch: see B7 |
| Chain vice or clamp, bench vice | Hold the saw and chain firmly | Fits the bar |
| Gearbox oil, grease | Tiller lubrication by the manual | From the manual |
| Chaps, glasses, gloves, ear protection | Chainsaw work protection | As Unit 1 |
Defined in full in Level 1 Appendix A12 and Appendix B13 below.
Tiller service and chain sharpening
- On a tiller: change the gearbox oil, check belt, clutch, tines and bolts. Record.
- Test the dead-man lever. Describe what must happen if it fails.
- On a chainsaw (engine off, plug cap off, chain in a vice): clean, check bar and sprocket, sharpen the chain with the correct file, set the gauge, and refit.
- Test the chain brake as the manual says. A qualified trainer watches.
- Write a service note for each machine.
Chain wear
Ask a chainsaw operator how often they sharpen and how they know a chain is dull. Write down what they say, and compare with this unit.
Check yourself
- What does a dull chain produce instead of shavings?
- What must be removed from the saw before sharpening?
- What do you do if the tiller's dead-man lever does not disengage the drive?
Unit 7 · Your workshop, pricing and marketing
A good mechanic who cannot price or find customers stays poor. Choose where to work, count every cost, and let customers know you are there.
Competency standard
| Learning outcome | Performance criteria: the trainee… |
|---|---|
| 7.1 Choose a good location | compares sites by customers, safety, cost and access |
| 7.2 Price services and plan a month | prices jobs and works out income and break-even |
| 7.3 Market the business | uses WhatsApp Business, a sign, a Google profile, referrals and a portfolio |
| 7.4 Keep records and comply | keeps job records and names registration and permit steps |
Range. One-person or two-person workshop or mobile service. Evidence. Costed quotes; monthly plan; marketing plan.
Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer before you act on any legal, licence or registration matter. For tax, VAT, PAYE and SSNIT, check with GRA or a qualified accountant. For loans and insurance, ask your bank, a licensed insurer or a qualified accountant. For fuel storage, fire, exhaust, pressure and other dangerous work, ask a qualified mechanic or a GhIE-registered engineer.
Location settings that give good returns
- Near the users. Vegetable farms, market gardens, farmland edges and roads farmers use. Visit on a market day and count pumps and tillers.
- Near fuel and spares (but never share a space with a fuel store).
- Safe place. Open-air test area, firm floor, shade, lock-up for tools and spares, and no neighbours downwind of exhaust.
- A mobile service (a motorbike or a pickup with tools and spares) saves rent and brings you to the farm.
- Group days. Offer a "farm engine service day" to a farmers' group, with a pack price.
Small business ideas and ingenuity
- Pump servicing packs for the farming season; spare-parts kits (plugs, filters, clamps, hoses).
- Pump hire and fuel delivery to farms (check fuel storage and licence rules first).
- Tine and chain sharpening; tiller servicing for hire operators.
- Sell hoses, strainers and foot valves; teach farmers the daily check.
- Water-delivery sums: help a farmer cost irrigation per bed (Unit 4).
Pricing and a monthly plan
One month
Example figures. You do 20 jobs in a month at an average price of GH¢250. Parts for each job average GH¢100. Fixed monthly costs: rent GH¢600, transport GH¢400, other GH¢300. (a) Monthly income? (b) Profit? (c) How many jobs break even each month? (d) A customer wants a 10% discount on a GH¢250 job: what is the new price and the margin after the GH¢100 of parts?
Marketing yourself
- WhatsApp Business profile with services, area and hours; short messages with photos of before and after (with permission).
- Google Business Profile so people searching "pump repair near me" find you; keep the address and hours correct.
- Signage at the workshop and on your toolbox, vehicle or bike.
- Referrals: ask each happy farmer to tell two neighbours.
- Portfolio: photos of old and new filters, cleaned carburettors, a pump you installed.
- Be honest about faults and costs; never replace parts that are not faulty.
Records and permits
- Register your business name at the Office of the Registrar of Companies (2026 fees in Level 1).
- Ask STMA about the business operating permit; the 2025 fee-fixing resolution lists fees by trade. The fee for an engine and pump workshop was not verified.
- Keep a job book; from Level 3 you learn full accounts.
Accessibility note
The Persons with Disability Act 2006 protects people with disability. Bench work (carburettor cleaning, chain sharpening in a vice, plug and filter service), parts selling, quoting, records and WhatsApp marketing can be done seated or with adjusted tools and benches. Pulling starter cords and carrying engines may need helpers or a trolley. Ask your Assembly about disability support. (Funding details: not verified here.)
SAFETY PROTOCOL: Workshop test bay and visitors
Before you start
- Open-air test bay marked; extinguisher, sand and first-aid kit in place; fuel stored away from the bay.
- Rules posted; visitors kept behind a line.
While you work
- Do: one engine running at a time; wear PPE; keep the area clear.
- Do not: run engines inside the shop; smoke; leave a hot engine on dry grass.
After you finish
- Stop all engines; let them cool; sweep and wipe spills; put used oil in the closed container.
- Write the day's faults in the log.
Emergency
- Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
- Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
- Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
- Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
Tools and items for this unit
| Item | What it is and when you use it | Size or type |
|---|---|---|
| Job card, receipt book, cash book | Record every job and payment | Printed or exercise book |
| Signboard and phone | Marketing | Any |
Defined in full in Level 1 Appendix A12 and Appendix B13 below.
Workshop plan
- Choose two possible locations. Score them on customers, safety, cost and access.
- Write a one-page plan: services, prices, tools, monthly sums using the exercise method, and break-even.
- Write your WhatsApp Business profile and a sign.
- Present it to the class.
Walk the market
Count the pumps, tillers or chainsaws in use on one farming street or market day. Ask three owners what faults they have had and what they paid.
Check yourself
- Name two good location settings for a pump mechanic.
- What is break-even?
- Name three ways to market yourself.
Appendix B · Technician reference layer
A bench book for the technician. Tables first, teaching text second. Every figure names its engine and its source. If your engine's own manual or shop manual says something different, the manual wins.
Ask a qualified expert. This appendix covers fuel, fire, exhaust, electrical spark, pressure, lifting, chemicals, water-use law and money. It is general information for trained technicians, not a replacement for the maker's shop manual. For engine, fuel, fire, exhaust or pressure work ask a qualified mechanic or a GhIE-registered engineer; for law, permits and contracts ask the named office or a qualified lawyer; for injury, burns, poisoning or illness see a doctor or nurse and call 112. Do not attempt work you are not trained and authorised to do.
B1. Typical service data by engine family
Rule for this table. Each row names the engine. Cells marked "not found" were looked for and not found in an open source. Fastener torque: no open source found for any of these engines. Print nothing, use the shop manual.
| Item | Honda GX120 (in the WB20XT pump) | Honda GX160 (in the WB30XT pump) | Chinese 168F-type copy | Briggs and Stratton |
|---|---|---|---|---|
| Engine type | 4-stroke, overhead valve, single cylinder | same | not found (usually called GX160-type; confirm on your engine) | Many series |
| Displacement | 118 cc (7.2 cu in) | 163 cc (9.9 cu in) | not found | By model number |
| Bore and stroke | 60.0 x 42.0 mm | 68.0 x 45.0 mm | not found | By model number |
| Spark plug gap | 0.70 to 0.80 mm | 0.70 to 0.80 mm | not found | By series |
| Valve clearance, cold | Intake 0.15 plus or minus 0.02 mm; exhaust 0.20 plus or minus 0.02 mm | Sources disagree, see the note below | not found | By series; look up by model number |
| Idle speed | 1,400 rpm plus or minus 150 | 1,400 rpm plus or minus 150 | not found | By series |
| Oil | SAE 10W-30, 0.56 L | SAE 10W-30, 0.58 L | not found | By series |
| Fuel tank | 2.0 L | 3.1 L | not found | By model |
Valve clearance on the GX160 is a conflict, not a number to use. The text I extracted from the Honda WB30XT owner's manual prints intake 0.08 mm and exhaust 0.10 mm (each plus or minus 0.02 mm), while a UK dealer maintenance sheet lists 0.15 mm intake and 0.20 mm exhaust for the GX160. The PDF's table layout may have scrambled in extraction. Not verified: use the Honda shop manual for your engine's serial number before adjusting. A dealer also lists spark plug types for the GX160 (NGK BPR6ES or BP6ES, Denso W20EPR-U or W20EP-U); these were read only in a summary and are not verified.
Briggs and Stratton. Values differ by series and model number, so look the engine up by its model number in the maker's manual. Do not carry a number from one series to another.
Compression readings. The Honda owner's manual gives no compression figure; no open source figure was found. Take the figure from the shop manual and record your readings (Appendix B9).
B2. Compression test: how to read it
| Step | Do this | Record |
|---|---|---|
| 1 | Warm engine, not hot; plug cap away from the hole | Engine make, model, hours |
| 2 | Fit the gauge in the plug hole (screw-in types seal better than push-in) | Gauge type and thread |
| 3 | Throttle fully open; pull until the needle stops rising | Reading 1 (psi, kPa or bar: write the unit) |
| 4 | Repeat | Reading 2 |
| 5 | Wet test: about a teaspoon of clean oil in the hole, test again | Reading 3 |
| 6 | Compare with the maker's figure | Pass, low, or zero |
If the wet test raises the reading well, worn rings are likely; if it does not, think of a valve or head gasket leak. The wet test is only moderately accurate. Refer when the reading is low and the owner wants a rebuild, there are metal particles in the oil, or the engine knocks.
B3. Technician fault charts (order of cost and ease, not a statistic)
Work down each chart from the top. Change one thing at a time and test after each change.
Chart 1 · Will not start
| Order | Test | Pass looks like | If it fails |
|---|---|---|---|
| 1 | Fuel tap, switch, choke, fuel in tank | Tap ON, switch ON, choke closed (cold), fuel visible | Correct the setting; refuel |
| 2 | Fuel sample (jar test, Appendix A8 of Level 1) | Clear, no water | Drain tank and carburettor, fresh petrol |
| 3 | Plug: remove, look, check gap | Dry, light brown or grey tip, gap as the manual | Dry, clean, regap or replace; wet plug means flooded engine |
| 4 | Spark test with an inline tester (never bare hand) | A clear spark at the tester gap | See Chart 2 |
| 5 | Fuel reaching the carburettor: sediment cup, fuel filter | Clean fuel, no dirt or water | Clean or replace |
| 6 | Air filter | Clean | Clean or replace |
| 7 | Compression | As the maker's figure | See B2 and Chart 3 |
The engine causes follow the Honda WB manual chart; the order and the remaining tests are general practice.
Chart 2 · No spark
| Order | Test | Pass looks like | Fix |
|---|---|---|---|
| 1 | Stop-switch lead shorting the coil | Spark returns when the switch lead is disconnected | Repair or replace the switch or lead |
| 2 | Plug cap and plug | Cap pushed home; plug clean and dry | Replace plug or cap |
| 3 | Plug lead | No cracks or burn marks | Replace |
| 4 | Coil air gap and flywheel key | Gap as the maker's figure; key not sheared | Refer unless you have the shop manual |
| 5 | Coil | Resistance as the maker's figure | Replace; refer |
Chart 3 · Starts, runs weak or loses power
| Order | Test | Fix |
|---|---|---|
| 1 | Throttle on slow; air filter clogged | Move throttle; clean filter |
| 2 | Old or bad fuel | Drain and refuel |
| 3 | Fuel filter, sediment cup, tank vent | Clean or replace; check the cap vent |
| 4 | Plug gap and condition | Regap or replace |
| 5 | Carburettor | Clean (Level 2 Unit 2); never drill jets |
| 6 | Compression | B2 |
| 7 | Valve clearance, combustion chamber deposits | Dealer job (Honda marks both as dealer jobs) |
Chart 4 · Smoke
| Smoke | Likely cause | Check |
|---|---|---|
| Blue (oil) | Too much oil, worn rings or valve seals | Oil level; wet test |
| Black | Rich mix: choke stuck, air filter blocked, wrong jet | Choke; filter; carburettor |
| White (diesel) | Water in fuel or cold | Drain water; warm |
Chart 5 · Overheating
| Check | Fix |
|---|---|
| Cooling fins and fan cover blocked with grass or dust | Clean |
| Low oil | Top up to the mark |
| Lean mix (air leak, blocked jet) | Fix the leak; clean |
| Running overloaded or dry (pump) | Reduce load; stop; re-prime |
Chart 6 · Pump: no water, low pressure, noise, leaks
| Symptom | Likely cause | Test and fix |
|---|---|---|
| No water | Not primed; air leak; strainer out of water or clogged; collapsed hose; excessive head | Prime; check connector, sealing washer, clamp; sink the strainer; replace hose; reduce head |
| Low output | Hose too long, too small, damaged; marginal head; clogged strainer; weak engine | Shorten or enlarge hose; clean; lower head; see Chart 3 |
| Rattling noise | Cavitation (suction too long, narrow, leaking or too high) | Shorten and straighten the suction; fix leaks |
| Leaks at the shaft | Worn mechanical seal | Replace the seal (check for dry running) |
| Engine stalls under load | Delivery blocked; overload; fuel fault | Open delivery; Chart 3 |
Chart 7 · Diesel (see Unit 5) and Chart 8 · Tiller and Chart 9 · Chainsaw
| Machine | Symptom | Likely cause | Fix |
|---|---|---|---|
| Diesel | Cranks, will not start | Air in fuel, empty tank, blocked filter, water | Bleed; filter; drain water |
| Diesel | Starts, then dies | Blocked filter, air leak, blocked tank vent | Filters; fittings; vent |
| Diesel | Black smoke | Blocked air filter, overload, worn injector | Filter; reduce load; refer injector |
| Tiller | Will not drive | Belt slipping or broken, clutch cable out of adjustment | Inspect belt; adjust as the manual says |
| Tiller | Drive will not release | Dead-man lever or cable fault | Unsafe: stop use; repair |
| Chainsaw | Cuts crooked | Uneven sharpening | Re-file all cutters alike |
| Chainsaw | Chain does not cut, makes dust | Dull chain or raker too high | Sharpen; check depth gauges |
| Chainsaw | Does not run at idle properly | Carburettor or fuel mix problem | Fuel mix; clean filter; refer adjustment |
B4. Carburettor reference (float type)
| Part | What it does | Fault shown by |
|---|---|---|
| Float bowl | Holds a small reserve of petrol | Fuel leak, gum or water in the bowl |
| Float | Rises with the fuel level and shuts the needle valve | Flooding if stuck or leaking |
| Needle valve (float needle) | Opens and shuts the fuel inlet | Flooding or starving |
| Main jet | A calibrated hole that meters fuel at high speed | Weak at full throttle if blocked |
| Idle jet (pilot jet) | Meters fuel at idle | Hard to idle if blocked |
| Venturi | The narrow throat that speeds the air so it draws fuel | |
| Throttle plate | The flap that sets airflow and speed | Sticking |
| Choke plate | The flap that enriches the mix when cold | Black smoke if stuck closed |
| Drain screw | Empties the bowl; Honda's drain bolt sits with the sediment cup | Used when storing |
Clean the jets with soft fine wire or a jet-cleaning set, then blow clear. Never enlarge a jet with a drill. Photograph the parts before you strip.
B5. Pump hydraulics: formulas, tables, worked examples
Ask a qualified expert. Standard hydraulics is shown here. For any large or high-pressure system, or any design you will be paid for, ask a GhIE-registered engineer to check the numbers. Never connect a pump to an existing pressurised pipe, tank or borehole without a qualified plumber or engineer.
Total head = suction lift + delivery height + friction loss (+ pressure needed at a sprinkler). See the main unit. Honda says the discharge head capability is always greater than the suction head capability, so keep the suction part the shorter part of the total head.
Friction loss in a hose (Hazen-Williams, SI form). Loss in metres = 10.67 x L x Q^1.852 / (C^1.852 x D^4.87), with Q in cubic metres per second, L and D in metres, and C a roughness number; larger C means a smoother pipe. The formula is for water at ordinary temperatures. FAO says friction head rises roughly with the square of the flow and that plastic pipe is smoother than iron. The table below was recalculated by script from the formula with C = 150 (an assumed smooth-plastic value: an example, not a hose maker's figure). For C = 120 multiply the figures by 1.51. Lay-flat hose and old, dirty or soft hose can lose more than the formula says: ask the hose maker and a GhIE-registered engineer.
Metres of head lost per 100 m of straight hose, with the water speed in metres per second (inside diameters are nominal examples):
| Flow L/s | 50 mm: loss | 50 mm: speed | 80 mm: loss | 80 mm: speed | 100 mm: loss | 100 mm: speed |
|---|---|---|---|---|---|---|
| 2 | 2.2 | 1.02 | 0.2 | 0.40 | 0.1 | 0.25 |
| 4 | 7.8 | 2.04 | 0.8 | 0.80 | 0.3 | 0.51 |
| 6 | 16.6 | 3.06 | 1.7 | 1.19 | 0.6 | 0.76 |
| 8 | 28.2 | 4.07 | 2.9 | 1.59 | 1.0 | 1.02 |
| 10 | 42.7 | 5.09 | 4.3 | 1.99 | 1.5 | 1.27 |
| 15 | 90.4 | 7.64 | 9.2 | 2.98 | 3.1 | 1.91 |
| 20 | 154.0 | 10.19 | 15.6 | 3.98 | 5.3 | 2.55 |
Read it like this: pushing 10 litres a second through 100 m of 50 mm hose loses about 43 m of head, more than the best-case head of a small pump, so the water will not arrive. The same flow in 100 mm hose loses about 1.5 m. This is why Honda says a short, large-diameter hose reduces fluid friction and improves output. Fittings add loss as well: in short runs with many fittings the fitting losses can exceed the pipe losses.
Water speed. Speed = flow divided by the cross-section area (V = Q / A). Keep speeds modest: one US university note uses 5 feet per second (about 1.5 m per second) as a rule, but that is foreign and not verified for Ghana.
Hydraulic power and engine size. Power is mass flow x g x head, and 1 litre of water weighs about 1 kg, so hydraulic power in kW = 0.00981 x flow (L/s) x head (m); shaft power is hydraulic power divided by the pump efficiency. Overall efficiency is the product of the efficiencies: a 30% engine driving a 50% pump gives 15% overall.
| Worked example (numbers are examples) | Working | Result |
|---|---|---|
| 10 L/s lifted a total head of 15 m | 0.00981 x 10 x 15 | 1.47 kW of hydraulic power |
| Pump efficiency 50% (example) | 1.47 / 0.5 | 2.94 kW at the pump shaft |
| 3 L/s at 12 m, pump 50% | 0.00981 x 3 x 12 = 0.353; / 0.5 | 0.71 kW shaft |
The engine's rated power must be well above the shaft power. Pump and engine efficiencies must come from the makers' data. FAO notes that a small engine can deliver one kilowatt-hour while burning less than one litre of fuel, which is only an upper limit for a sanity check. Measure your own fuel use (Appendix B8).
Suction limit (a check, not a design). Atmospheric pressure supports about 10.4 m of water at sea level in theory. FAO says centrifugal pumps are generally limited to a suction lift of around 4.5 m with a short suction pipe, and that the usable lift falls with altitude (about 3 m less at 3,000 m), with hotter water (about 7% lower at 30 degrees C than at 20 degrees C) and with a longer suction pipe (an 80 m suction pipe works at about half the suction head). Honda's best-case suction head for the two WB pumps is 8 m. Real lift is much less than best case. Rule: suction lift + friction in the suction hose must stay well inside the practical limit; if in doubt, lower the pump.
Speed rules (pump affinity). For the same pump, flow changes in proportion to speed, head with the square of speed and power with the cube of speed. This is standard hydraulics, not verified in a source here: ask a GhIE-registered engineer before using it to change an engine speed (and never adjust the governor: see Level 1).
Derating. Engines lose power in heat and at altitude. A UK fire-pump rule of thumb exists for diesel engines (foreign, not verified for Ghana); for a real figure ask the engine maker.
Pump types, in one table. Type descriptions are general engineering knowledge, not source-checked; ask a dealer.
| Type | Use | Note |
|---|---|---|
| Centrifugal self-priming (this book) | Clean or lightly dirty water, farm irrigation | Needs priming; keeps suction short |
| Diaphragm pump | Dirty or slurry water | Check with the dealer |
| Piston (reciprocating) pump | Higher head, lower flow | FAO: suction lift should not normally exceed about 6.5 m |
| Multistage or high-pressure pump | Sprinklers needing pressure | Ask the dealer for the curve |
| Engine-driven submersible | Deep sources | See the hub's Boreholes and Water Pumps module |
| Hand and treadle pumps | No fuel | FAO lists comfortable hand-pump heads from 10 m to 25 m depending on cylinder size |
Hose size guide. Suction hose: reinforced, not smaller than the pump port (Honda WB20XT 50 mm, WB30XT 80 mm); delivery hose short and wide.
Water permission line. Mechanical abstraction up to five litres per second is exempt from a permit but must be registered with the District Assembly (L.I. 1692, regulations 10 and 11). Five litres per second is 300 litres per minute or 18 cubic metres per hour. The best-case flow of a Honda WB20XT is 575 L per minute and of a WB30XT is 1,041 L per minute. Measure the real flow before telling a customer which side of the line he is on.
B6. Diesel reference
| Topic | Rule |
|---|---|
| Daily | Fuel, oil, water in the fuel bowl, air filter, cooling fins, belts and guards (Unit 5) |
| Bleeding | Tank toward injectors; hand primer; injection side by a qualified diesel mechanic |
| Injector pressure test and nozzle fault-finding | Refer to a qualified diesel mechanic with a test stand |
| Fuel run-away and governor or stop-lever faults | Stop: refer. Never adjust the governor |
| Diesel quality | Ghana's diesel standard is called GS 141; the edition and limits are not verified: ask the Ghana Standards Authority. Water in diesel is a common cause of white smoke and poor running: drain the water bowl |
| Oil grades, valve lash, cold-start aids | From the maker's manual; no open figure found |
B7. Tiller and chainsaw reference
Chain filing (Stihl chains). The file diameter depends on the chain pitch; the standard filing angle is 30 degrees for Stihl chain (ripping chain 10 degrees, one chain type 25 degrees). This is the Stihl table (foreign): use the chain maker's card for your chain.
| Chain pitch | Round file diameter |
|---|---|
| 1/4 in | 4.0 mm |
| .325 in | 4.8 mm |
| 3/8 in | 5.2 mm |
Check the depth gauge with the filing gauge that matches the pitch; if it stands higher than the gauge, lower it with a flat file, then round the front.
| Chainsaw term | Meaning |
|---|---|
| Pitch | Distance between chain rivets; sets the file size |
| Gauge | The thickness of the drive links; must fit the bar groove |
| Drive links | The tabs under the chain that fit the sprocket and bar groove; the count depends on bar and pitch |
| Depth gauge (raker) | The small guide ahead of each cutter that limits the bite |
| Chain catcher | A stop that holds a broken chain |
| Anti-vibration mounts | Rubber mounts that cut hand vibration; long exposure to vibration can harm the hands, so rest and ask a doctor if fingers go numb or white |
Tiller items. Gearbox oil grade, belt size, clutch cable adjustment and tine count come from the tiller manual; no open figure was found. Tine types differ for hard and soft soil: ask the dealer.
Kickback and brake test. Kickback happens when a tooth at the bar tip catches wood; the chain brake should stop the chain; test it before each use and do not use a saw whose brake fails.
Chainsaw law. A news report says the ban on chainsaw lumber milling is still in force, but sources differ on the regulation number: not verified. Never mill lumber with a chainsaw; ask the Forestry Commission.
B8. Calculation card
| Job | Formula | Example (numbers are examples) |
|---|---|---|
| Flow from a bucket | litres / seconds | 20 L in 4 s = 5 L/s |
| L/s to m3/h | x 3.6 | 5 L/s = 18 m3/h |
| Water for a bed | mm x area in m2 = litres (1 mm over 1 m2 is 1 litre) | 6 mm on 200 m2 = 1,200 L |
| Hours to water | litres / (flow in L/h) | 1,200 L / 1,800 L/h = 0.67 h |
| Fuel per hour (measured) | litres added back to the mark / hours run | 1.2 L/h |
| Fuel per m3 | (L/h x price) / (m3 per hour) | (1.2 x GH¢15) / 18 = GH¢1.00 per m3 |
| Hose speed | Q / A | see B5 |
The fuel price used is an example, not a real price. To fill the card with real numbers use a measured fuel use, a measured flow and today's price at the fuel station.
B9. Forms
Job card
| Field | Entry |
|---|---|
| Job number, date, customer | |
| Machine and engine model, serial | |
| Hours or reading | |
| Fault reported by the owner | |
| Fault found | |
| Work done | |
| Parts used and cost (GH¢) | |
| Labour hours and rate | |
| Deposit paid, balance | |
| Tested by, date, customer signature |
Compression and spark record
| Date | Engine | Gauge type | Dry reading | Wet reading | Maker's figure | Spark seen (yes/no) | Result |
|---|---|---|---|---|---|---|---|
Fault report: machine, symptom, first checks, chart used, tests done with readings, conclusion, refer or fix, who was told.
Comeback log: date of first job, date it came back, same fault or new, cause, free or paid, lesson.
B10. Clean, replace or refer
| Part | Clean | Replace | Refer |
|---|---|---|---|
| Spark plug | Light carbon: brush | Worn tip, cracked porcelain, burnt electrode | |
| Air filter | Foam: wash and dry; paper: tap | Dirty or damaged paper; torn foam | |
| Fuel filter and sediment cup | Wash cup in non-flammable solvent | Clogged filter | |
| Carburettor jets | Wire or jet set, blow clear | Damaged or enlarged | |
| Mechanical seal and impeller | Leaking seal; worn impeller | Impeller clearance is a dealer job | |
| Valves, rings, crankshaft | Refer | ||
| Diesel injectors and injection pump | Refer | ||
| Governor | Refer; never adjust |
B11. Stop and refer: one table
| Refer when | To whom |
|---|---|
| Low compression and the owner wants a rebuild | Qualified mechanic or the engine dealer |
| Metal in the oil, knocking, seized engine | Qualified mechanic |
| Diesel injection side, injector pressure test | Qualified diesel mechanic |
| Governor, valve clearance, idle speed adjustments | Honda dealer or shop manual (Honda marks them dealer jobs) |
| Water permit questions | Water Resources Commission; District Assembly |
| Large or high-pressure irrigation design | GhIE-registered engineer |
| Chainsaw law | Forestry Commission |
| Fire certificate, extinguisher type | Ghana National Fire Service |
B12. Mistake catalogue for the technician
- Changing two things at once, so you do not know what fixed it.
- Drilling a jet.
- Touching the governor.
- Using a figure from another engine.
- Testing spark with a bare hand.
- Cleaning a plug with a wire brush hard enough to leave metal traces.
- Fitting a hose smaller than the pump port.
- Quoting a pump by its "maximum head".
- Starting a pump you have not primed.
- Filing chain cutters unevenly.
- Skipping the brake test.
- Selling a "reconditioned" engine without a compression reading in the record.
B13. Tools and Items Glossary (added at Level 2)
These are the items added to the Level 1 list (Appendix A12 in Level 1). Also called: other common English or trade names. Local names for tools differ from town to town. Use the standard name given here when you order or ask for help, and show the picture.
| Item | What it is and what it does | Size or type | Also called | Used in |
|---|---|---|---|---|
| Inline spark tester | A gap tester put in the plug lead; shows spark as a flash; a blue-white spark is the sign you want | Fits the plug cap | spark gap tester, ignition tester | U1 |
| Compression tester (gauge) | A pressure gauge with a hose or thread that fits the plug hole; reads cylinder pressure | Screw-in or push-in; thread must fit the plug hole; psi, kPa or bar | compression gauge, cylinder pressure gauge | U3 |
| Leak-down tester | A compressed-air tester with two gauges that shows how much air leaks and where | Needs an air compressor | cylinder leakage tester, leakage gauge | U3 |
| Compressed air line | Blows cleaning dust and cleaner from small passages; wear eye protection | From a small compressor | air line, air hose | U2 |
| Carburettor cleaner | A solvent for gum and varnish; fire risk; do not soak rubber or plastic | Aerosol or can | carb cleaner, carb spray | U2 |
| Jet cleaning set (soft wire, fine wire) | Thin wires or drill-bit style cleaners to clear a jet without enlarging it | Several sizes | jet cleaner set, carb cleaning wires, needle set | U2 |
| Bench vice | A clamp fixed to a bench; holds a part or engine while you work | Medium | vise, bench clamp | U6 |
| Chain vice or clamp | Holds a chainsaw bar firmly for filing | Fits the bar | chain clamp, bar vice | U6 |
| Torque wrench | A wrench that clicks at a set tightness in N.m or ft.lb; use the shop-manual figure | 3/8 in drive is common for small engines | click wrench, torque spanner | U3 |
| Round file and file holder | A round file the right diameter for the chain, in a holder that guides the angle | 4.0, 4.8 or 5.2 mm by pitch | chain file, file guide, sharpening guide | U6 |
| Flat file and depth-gauge tool | Lowers the depth gauges to the right height | Matches the pitch | raker file, depth gauge tool, filing gauge | U6 |
| Chainsaw chaps | Layered trousers that clog a chain; they reduce but do not remove risk | From the supplier | chainsaw trousers, leg guards | U6 |
| Tape measure | Measures suction lift, delivery height and hose length | 5 or 8 m | measuring tape, steel tape | U4 |
| Spirit level or clear tube level | Shows level or measures height difference with water in a clear tube | Any | bubble level, water level | U4 |
| Pressure gauge | Shows pressure at the pump or sprinkler; bar, kPa or psi | 0 to 6 bar for small pumps (example) | manometer, pressure meter | U4 |
| Multimeter | Meter for volts and resistance; used on coil and wiring (see Electronics Repair) | Basic digital | multi-tester, volt-ohm meter, VOM | U1 |
| Tachometer | Reads engine speed in rpm for idle speed checks | Optical or clip-on | rev counter, rpm meter | U1 |
| Float | The part that rides on the fuel in a carburettor bowl | From the maker | carburettor float, float arm | U2 |
| Needle valve | Opens and closes the carburettor fuel inlet | From the maker | float needle, inlet needle | U2 |
| Main jet and idle jet | Calibrated holes that meter fuel | From the maker | high-speed jet, pilot jet, slow jet | U2 |
| Venturi, throttle plate, choke plate, drain screw | Carburettor parts (see B4) | From the maker | air horn, butterfly valve, choke flap, bowl drain | U2 |
| Diaphragm carburettor | A carburettor with a flexible diaphragm, used in saws so it works at any angle | From the maker | membrane carburetor, saw carburetor | U6 |
| Coil air gap | The small gap between the coil and flywheel magnets; set by the maker's figure | From the shop manual | magneto gap, armature gap | U1 |
| Flywheel key | A small key that locks the flywheel to the shaft; a sheared key upsets spark timing | From the maker | woodruff key, shaft key | U1 |
| Valve, valve seat, rocker, pusher (tappet) | The parts that open and close the engine's gas ports | From the maker | poppet valve, seat, rocker arm, tappet or lifter | U3 |
| Piston rings | Rings that seal the piston in the cylinder; worn rings lower compression | From the maker | compression rings, rings | U3 |
| Head gasket | A seal between head and block | From the maker | cylinder head gasket | U3 |
| Combustion chamber | The space above the piston where the fuel burns; Honda lists cleaning it as a dealer job | From the maker | cylinder head chamber | U3 |
| Injector, injection pump, glow plug | Diesel parts: injector sprays the fuel, the pump times and meters it, a glow plug heats a cold engine | From the maker | nozzle, fuel pump, heater plug | U5 |
| Hand primer | A small pump lever on a diesel filter that fills the lines with fuel | On the fuel pump or filter | priming pump, primer lever, bleed pump | U5 |
| Water bowl (separator) | A glass or plastic bowl under the filter where water settles | On the filter | water trap, fuel water separator | U5 |
| Wear ring and impeller clearance | The close gap between impeller and casing; a worn gap lowers output; dealer check | From the maker | wear plate, casing clearance | U4 |
| Check valve (pump inlet valve) | Lets water in but not back out | From the maker | non-return valve, one-way valve | U4 |
| Gate valve, ball valve | Valves that shut the delivery line; a ball valve turns a quarter turn | Matches pipe size | shut-off valve, isolation valve, stopcock | U4 |
| Bends, tees, reducers, unions | Pipe fittings; each adds friction loss | Matches pipe size | elbows, T-pieces, adaptors, couplings | U4 |
| Clutch drum, sprocket, oil pump, chain tensioner | Chainsaw drive and oiling parts | From the maker | clutch bell, drive sprocket, bar-oil pump, chain adjuster | U6 |
| Drive belt, clutch cable | Tiller drive parts; belt size from the manual | From the maker | V-belt, control cable | U6 |
| Penetrating oil, thread sealant, gasket sealant | Consumables for stuck bolts, joints and seals; use sparingly | From the dealer | release oil, thread tape or paste, gasket maker | U3 |
| Carburettor kit | Gasket, needle, float and jets for one model | By model | carb repair kit, rebuild kit | U2 |
| Gaskets, O-rings, seals | Soft seals that stop leaks; the right one per model | By model | packing, rubber rings, oil seals | U3 |
| Fuel line and filter | Rubber line and an inline filter; Honda says to check the fuel tube every 2 years | From the maker | petrol hose, inline fuel filter, fuel pipe | U2 |
Starter bench kit (suggested). Metric spanners and sockets, plug spanner, feeler gauges, inline spark tester, compression tester, screwdrivers and pliers, bench vice, jet-cleaning set, funnel, drain tray, marked cup, clean rags, wire brush. Field kit (suggested). Spare plugs, air and fuel filters, hose clamps, a strainer, sealing washers, a small spanner set, plug spanner, a spare pull cord, rags, gloves, glasses, and a first-aid kit. Cost class: cheap for hand tools, medium for testers, dear for a compressor or leak-down tester.
Glossary
| Term | Meaning |
|---|---|
| Bleeding | Removing air from a fuel system |
| Compression test | A test of how well the cylinder holds pressure |
| Depth gauge (raker) | Part that limits how deep a chain tooth cuts |
| Head | Height of a column of water, used to measure energy |
| Head loss | Energy lost to friction in hoses and fittings |
| Jet | A small hole in a carburettor that meters fuel |
| Kickback | A sudden backward jump of a chainsaw |
| Priming lever | A hand pump on a diesel to push fuel through |
| Spark tester | A safe gap to see the spark |
| Suction lift | Height from the water up to the pump |
| Valve clearance | The small gap that lets a valve close fully |
Logbook
Copy these pages into an exercise book. Your logbook is part of your assessment evidence.
- Unit 1: plug photos and readings; fault tree; spark test records
- Unit 2: carburettor photos before and after; step record; service note
- Unit 3: compression and wet-test readings; owner note
- Unit 4: head and flow sheet; layout sketch; recommendation
- Unit 5: diesel checklists; bleeding steps
- Unit 6: tiller and saw service notes; sharpening record
- Unit 7: monthly plan; break-even; marketing plan
- Every homework, dated
Self-check quiz
- Why must you not hold a plug lead while the engine turns over?
- What does a light brown plug tip show?
- Why must you never enlarge a carburettor jet with a drill bit?
- Name three things to check before you strip a carburettor.
- What does the wet test in a compression test show if the reading rises?
- When do you refer a low-compression engine to a qualified mechanic?
- Give the three parts of total head.
- Why is a pump's "maximum head" not enough to choose a pump?
- How does a diesel engine ignite its fuel?
- What is the first step in bleeding a diesel, and who handles the injection side?
- What must be off and removed before sharpening a chain?
- How many jobs break even if fixed costs are GH¢1,300 and the margin per job is GH¢150 (example)?
Further reading and sources
Best next reads: your engine's, pump's and chainsaw's manuals; Level 3 of this module; the hub's Workplace Safety module.
What this module does not cover: engine rebuilding, injection-pump and injector work, flywheel and coil setting, full irrigation design (Level 3), generators, outboards, motorbikes, tractors, boreholes, and Ghana prices of engines and spares (not verified; ask local dealers).
Every source used in this manual is listed, with links, in the Teacher Copy.