← All training manualsSmall Engines and Irrigation Pumps · read-onlyGet the PDF with Teacher Copy (GH¢50)
Training module · National Proficiency I · CTVET formatTrainee Manual

Small Engines and Irrigation Pumps

A skill that keeps farms working. Learn to run, check and service a small engine and a water pump safely, and to start earning from it.

A small petrol engine pump watering a vegetable bed On the left a petrol water pump with a red fuel tank, a pull-start handle and a guard frame sits on firm ground beside a jerrycan. A suction hose runs to a pond and a delivery hose runs to a vegetable bed with green rows and a spray of water. On the right a power tiller and a chainsaw rest on a work bench with a toolbox and a spark plug. IRRIGATION PUMPWATER TO THE BEDTILLERS · CHAINSAWS
Trainee name
Training centre
Start date
Instructor
Prepared by De-Graft Afful · Version 1.1.0 · November 2026
01

About this module

A farm without a working pump or tiller loses days it cannot afford. Most small engines fail because of dirty fuel, a blocked air filter, a worn plug or no oil, and all of these can be found and fixed by a careful beginner. This module teaches you to do that safely, and to earn from it.

Who it is for. People with no formal certificate, aged 18 or over. National Proficiency I is a bridging level for people with little or no formal education; holders do routine tasks under supervision. In Ghana, nobody under 18 may do hazardous work.

Why small engines and pumps

  • Small motor pumps matter for smallholder irrigation: a study says smallholders can play a big part in national irrigation plans if they can get water-lifting technology, especially small motorised pumps.
  • Most irrigated land in Ghana is managed informally by smallholder farmers, not government schemes. Those farmers need someone who can keep their pumps running.
  • This module teaches servicing and light fault-finding. It does not teach engine rebuilding. That comes at Level 2 and 3.

No official CTVET unit list was found for small engines. This module is not a CTVET curriculum. Ask CTVET or the regional Ghana TVET Service office whether a standard exists, and match this module to it if so.

What this module does not cover

Petrol generators are in the hub's Appliance and Generator Repair module. Outboard motors are in Outboard Motor Repair. Motorbikes and tricycles are in Motorbike and Tricycle Servicing. Tractors are in Tractor Operation. Boreholes and submersible pumps are in the hub's Boreholes and Water Pumps module. Pipes and fittings are in Basic Plumbing. This module covers petrol irrigation pumps, power tillers and chainsaws, and their basic servicing only.

How the module works

Each unit has learning outcomes, performance criteria, the range and the evidence your assessor needs. You are judged Competent or Not Yet Competent by being watched at work, by your tasks, by answering questions, and by your logbook. About 70% of the time is practical. Every unit ends with homework and a short Check yourself.

02

Unit 1 · Work safely with fuel, fire, exhaust and moving parts

A small engine can burn you, poison you, cut you and deafen you. Almost every one of these accidents is preventable. Safety is the first skill, and it is a gate: you cannot move on without it.

Competency standard

Learning outcome Performance criteria: the trainee…
1.1 Handle fuel safely stores and pours petrol in approved containers, outdoors, with the engine off and cool
1.2 Prevent fire keeps ignition sources away from fuel; knows where the extinguisher and sand are
1.3 Avoid exhaust poisoning runs engines only outdoors, in open air, away from doors and windows
1.4 Protect body wears safety glasses, ear protection, gloves, boots; no loose clothing
1.5 Respect moving and hot parts never touches a running belt, blade, tine, chain or hot silencer

Range. All workshop and field work. Evidence. Observation every session; oral questions.

Ask a qualified expert. For fuel, fire, exhaust, pressure, electrical or any dangerous work, ask a qualified mechanic or a GhIE-registered engineer, and use a qualified safety officer. Do not attempt work you are not trained and authorised to do. For any injury, burn, poisoning or illness, see a doctor or nurse; in an emergency call 112. This unit teaches awareness and good practice, not medical treatment. This is general information, not legal advice; ask a qualified lawyer before you act on any legal matter.

Petrol: the main danger

Petrol gives off vapour that burns very easily. The rules below come from UK safety guidance (foreign, but the physics is the same in Takoradi).

  • Do not keep petrol unless you must.
  • Never bring petrol into a house or any place where people live.
  • Keep containers away from children and direct sunlight, with caps tight; an empty container can still hold fumes, so store it the same way.
  • Put the container on the ground when you fill it.
  • Let a hot engine cool before refuelling, and refuel outdoors away from buildings.
  • Never use petrol to light a fire.

Ghana adds a licence rule for business: the National Petroleum Authority says commercial storage and sale of petroleum products needs an NPA licence. Rules for small farm quantities were not verified. Ask the NPA, the Ghana National Fire Service or your District Assembly before you store petrol for sale or in large amounts.

How much petrol can I keep? No Ghana rule for small farm containers was found. UK guidance gives its own limits, which do not apply here. Keep the least you can, in approved, closed containers, outdoors in the shade, away from cooking fires and sockets, and ask the Ghana National Fire Service for local advice.

Exhaust: carbon monoxide

Engine exhaust contains carbon monoxide (CO), a gas you cannot see or smell. Signs of poisoning are headache, dizziness, weakness, stomach upset, vomiting, chest pain and confusion, like the flu; heavy exposure can cause fainting or death, and a sleeping person can die without any signs.

  • Never run an engine indoors, in a garage or in a closed space, even with doors and windows open.
  • In the field, stand upwind and keep the exhaust pointing away from people.
  • If someone feels headache, dizzy or sick near an engine, switch it off, move everyone into fresh air, and get medical help. Call 112 in an emergency.

Noise, heat and moving parts

  • Wear ear protection when an engine runs for a long time. Small engines are loud.
  • The silencer (muffler) stays very hot after the engine stops. Do not touch it, and do not park a hot engine on dry grass.
  • Keep hands, hair, clothes and tools away from belts, fans, flywheels, blades, tines and chains while an engine runs. Switch off and wait until everything has stopped before you touch a moving part.
  • Wear closed boots, gloves for handling, and safety glasses. No loose clothes, no dangling cloth, no flip-flops.

Fire safety in the workshop

  • Keep a fire extinguisher and a bucket of sand where you can reach them without crossing the fire.
  • Never smoke or use a naked flame near fuel.
  • Wipe up spills at once; let the wiped area dry before starting an engine.
  • Know where the nearest exit is and where to call: 112.

Safe or unsafe?

Your trainer describes eight scenes. For each, say safe or unsafe and why.

SAFETY PROTOCOL: Refuelling and handling petrol

Before you start

  • Engine off and cool; wait until the silencer has cooled.
  • Outdoors, in the shade, away from buildings, flames, cooking fires and sockets.
  • Approved container, cap tight, label clear; container on the ground.
  • PPE: safety glasses and gloves; extinguisher and sand within reach.

While you work

  • Do: pour through a clean funnel, slowly, and stop below the filler neck.
  • Do not: smoke, use a phone flame or light, or refuel a hot engine.
  • Do not: use petrol to light a fire or clean hands.

After you finish

  • Wipe spills and let the area dry before starting.
  • Close the cap and the container; store the container as in Unit 1.
  • Report a leak or damaged container to your trainer at once.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.

Tools and items for this unit

Item What it is and when you use it Size or type
Fire extinguisher Cylinder for small fires; keep within reach, never cross the fire to reach it Type: ask the Ghana National Fire Service
Sand bucket Smothers a small spill fire About 10 litres
Approved fuel container Closed container for petrol or mixed fuel From the dealer
Safety glasses, ear protection, gloves, closed boots Wear for every engine session Fit the wearer
First-aid kit Small injuries; for serious injury call 112 From a pharmacy

Defined in full in Appendix A12.

Safety set-up

  1. Put on safety glasses, ear protection, gloves and closed boots; your partner checks you.
  2. Walk the workshop and the practice area. Find the extinguisher, sand bucket, first-aid kit, exit and the open-air engine bay. Mark them on a sketch.
  3. Check each fuel container: closed cap, no leaks, clearly marked petrol or mixed fuel.
  4. Practise pouring water (not fuel) from a container into a funnel on the ground, with no spill.
  5. Practise the shutdown routine: stop switch, wait, check it has stopped, keep clear of the silencer.
  6. Record the checks in your logbook.

Look around

Visit a place that sells or uses petrol (a fuel station, a mill, a farm), from a safe distance. Note three safe things and three unsafe things you see. Do not take photos of people without asking.

Check yourself

  1. Name two rules for refuelling a small engine.
  2. Why must you never run an engine in a closed shed, even with the door open?
  3. What do you do before touching a moving part?
03

Unit 2 · Know your small engine

You cannot fix what you cannot name. Learn the parts and what each one does, in plain words.

Competency standard

Learning outcome Performance criteria: the trainee…
2.1 Explain how an engine works describes the four strokes and says what a two-stroke does differently
2.2 Name the parts names and finds the main parts on a real engine
2.3 Choose and use basic tools uses the right spanner, plug spanner and screwdriver without damage
2.4 Read the label and manual finds model, oil type, and service advice in the manual

Range. Small air-cooled petrol engines: four-stroke (pump engine) and two-stroke (chainsaw, some tillers). Evidence. Parts naming on a real engine; oral questions.

Ask a qualified expert. For fuel, fire, exhaust, pressure or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. Do not attempt work you are not trained and authorised to do.

The four-stroke engine

A four-stroke engine's piston makes four strokes, and the crankshaft turns twice, to finish one cycle:

  1. Intake. The piston goes down and draws in a mix of air and fuel.
  2. Compression. The piston goes up and squeezes the mix.
  3. Power. The spark plug ignites the mix and the burning gas pushes the piston down.
  4. Exhaust. The piston goes up again and pushes the used gas out.

Remember it as suck, squeeze, bang, blow. Petrol engines use a spark plug; diesel engines ignite the fuel by the heat of compression instead.

The two-stroke engine

A two-stroke engine finishes its cycle in one turn of the crankshaft, so it has a power stroke every turn. It has fewer moving parts and a high power for its weight, which is why chainsaws use it. It has no oil sump, so oil is mixed into the fuel to lubricate it. This is why the correct mix matters so much (Unit 3).

Four-stroke Two-stroke
Typical use here Pump engines, many tillers Chainsaws, some small tillers and brush cutters
Oil Separate oil in the engine, checked on the dipstick Mixed into the petrol
Fuel in tank Plain petrol Petrol plus oil, mixed correctly
Weight Heavier Lighter

The main parts (name them on a real engine)

Part What it does
Fuel tank and tap Holds petrol; the tap opens and closes the flow
Carburettor Mixes fuel with air
Air filter Keeps dust out of the engine
Spark plug Makes the spark that lights the mix
Recoil starter (pull cord) Turns the engine over by hand to start it
Flywheel and ignition coil Make the electricity for the spark
Cylinder and piston Where the burning happens
Crankcase and sump (four-stroke) Holds the crankshaft and engine oil
Oil filler and dipstick Where you add and check oil
Silencer (muffler) Quietens the exhaust; very hot
Throttle and stop switch Control speed; stop the engine
Governor Keeps engine speed steady (do not adjust)

Do not adjust the governor or the top speed screw. Running an engine faster than the maker intended can break it and hurt you. Leave the governor to a qualified mechanic.

Basic tools

  • Spanners and a socket set (metric); a plug spanner that fits your plug; flat and cross screwdrivers; pliers; a wire brush; a small paintbrush.
  • Feeler gauges to measure the plug gap (Level 2 uses them more).
  • A funnel, clean containers, a drain tray, and clean rags.
  • Use the right size. A wrong spanner rounds off a bolt and costs more than the job earns.

Read the manual and the label

Every engine and pump has a model label and a maker's manual. The manual gives the oil type, how often to service, the plug type and the safe way to run the machine. For example, Honda publishes owner's manuals for its WB20XT and WB30XT water pumps. Always follow your engine's manual, not a number you heard from a friend. Appendix A1 gives the typical Honda WB20XT and WB30XT figures (plug gap, oil quantity and grade, plug spanner size) as examples of what a manual says; they are typical for those two models, not universal, so write your own engine's figures in the blank column.

Labelled small four-stroke petrol engine Side view of a small air-cooled four-stroke petrol engine with numbered parts: fuel tank, fuel tap, carburettor, air filter, spark plug, cylinder with cooling fins, crankcase and sump, oil filler and dipstick, silencer, recoil starter, throttle lever and stop switch, ignition coil with flywheel, and governor arm. Small four-stroke petrol engine, side view 1 2 3 4 5 6 7 8 9 10 11 12 13
A small four-stroke petrol engine with every main part numbered. Use the table to learn each part and its safety rule.

Parts and safety rules

No. Part What it does Safety rule
1 Fuel tank Holds the petrol Refuel only when cool, outdoors, with the engine off
2 Fuel tap (fuel valve) Opens and closes the flow of fuel to the carburettor Close it for moving and storing the machine
3 Carburettor Mixes fuel with air A fuel leak here is a fire risk; do not adjust it until trained
4 Air filter Stops dust entering the engine Never run the engine without it
5 Spark plug Makes the spark that lights the mix Pull the cap, not the wire; never test with a bare hand
6 Cylinder with cooling fins Where the fuel burns; fins shed heat Very hot: do not touch; keep fins clean
7 Crankcase and sump Holds the crankshaft and the engine oil Drain oil only from a warm, stopped engine into a tray
8 Oil filler and dipstick Where you add and check oil Check on level ground with the engine off; do not overfill
9 Silencer (muffler) Quietens the exhaust Stays very hot after stopping; keep dry grass and clothes away
10 Recoil starter (pull cord) Turns the engine by hand to start it Hold the machine firm; never let the cord snap back
11 Throttle lever and stop switch Set speed and stop the engine Know where the stop switch is before you pull the cord
12 Ignition coil and flywheel Make the electricity for the spark Never touch while the engine runs; the lead carries high voltage
13 Governor arm Keeps engine speed steady Do not adjust: over-speed can break the engine and hurt you

SAFETY PROTOCOL: Working on a small engine (inspection and parts hunt)

Before you start

  • Engine off, cold, fuel tap closed; plug cap pulled if you will turn the engine.
  • Open-air bench or bay; extinguisher and sand within reach.
  • PPE: glasses, gloves, closed boots; no loose clothing.

While you work

  • Do: use the right spanner; keep parts in a tray in order.
  • Do not: start the engine during an inspection; touch the silencer; adjust the governor.

After you finish

  • Refit all covers and guards; wipe the engine and the area.
  • Log what you checked; report faults and leaks.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.

Tools and items for this unit

Item What it is and when you use it Size or type
Spanner set and socket set Undo nuts and bolts without rounding them Metric
Plug spanner Fits the spark plug only; never a loose spanner Honda WB manual 13/16 in; match your plug
Feeler gauge Measures the plug gap Blade thickness in mm
Screwdrivers and pliers Covers, clamps and small parts Several sizes
Wire brush, paintbrush, rags Cleaning Small

Defined in full in Appendix A12.

Parts hunt

  1. With the engine off, cold, and the fuel tap closed, find and touch each part in the table.
  2. Draw the engine from the side and label ten parts.
  3. Find the model label. Write down the engine make, model and the manual page for oil and plug.
  4. Practise using the plug spanner on a loose plug without turning it into the engine (the trainer watches).
  5. Put the parts-hunt drawing in your logbook.

Spot the engines

List five small engines you see on your farm, in your market or in your town (pump, mill, tiller, chainsaw, generator). Say whether each is likely to be a two-stroke or a four-stroke and how you could tell.

Check yourself

  1. Say the four strokes in order.
  2. Why is oil mixed into the fuel of a two-stroke engine?
  3. Where do you find the right oil and plug for your engine?
04

Unit 3 · Fuel, oil and lubrication

Most engines die of bad fuel, no oil or the wrong oil. This unit is cheap to learn and saves the most money.

Competency standard

Learning outcome Performance criteria: the trainee…
3.1 Use the right fuel uses clean petrol and avoids stale or dirty fuel
3.2 Mix two-stroke fuel mixes by the maker's ratio, measured, in a labelled container
3.3 Check and change engine oil checks the dipstick on level ground and changes oil as the manual says
3.4 Store and dispose stores fuel safely and takes used oil to a proper place

Range. Petrol, two-stroke oil, four-stroke engine oil. Evidence. Mixing task; oil check and change; oral questions.

Ask a qualified expert. For fuel, fire, chemical or environmental questions, ask a qualified mechanic, a GhIE-registered engineer, or the EPA. Do not attempt work you are not trained and authorised to do.

Clean fuel

  • Use clean petrol from a licensed fuel station. Water or dirt in the tank blocks the carburettor.
  • Pour through a funnel with a clean cloth or filter.
  • Do not use fuel that smells sour or looks cloudy. Old petrol goes stale.
  • Use fresh fuel for two-stroke mixes. One manufacturer's manual advises not mixing more than you will use in 30 days, or 60 days if a fuel stabiliser is added.

Mixing two-stroke fuel

The ratio of petrol to oil is set by the engine maker and is printed in the manual or on the engine. It is not the same for every engine. A common figure is 50 parts petrol to 1 part oil (50:1), but the correct ratio is the maker's, so always check.

How to mix correctly:

  1. Find the ratio in your manual. Write it on the container.
  2. Use a clean, approved fuel container, outdoors, on the ground, engine off, no flame.
  3. Measure the oil with a marked cup. Do not guess by the bottle cap.
  4. Pour half the petrol into the container, add the oil, close the cap and shake, then add the rest of the petrol and shake again.
  5. Label the container "MIXED FUEL, 2-STROKE", with the ratio and the date.
  6. Use mixed fuel only in the two-stroke engine. Never pour mixed fuel into a four-stroke pump engine.

Mixing maths

A manual says to mix at 50:1. (a) How much oil is needed for 5 litres of petrol, in millilitres? (b) If you wrongly use 1 part oil to 25 parts petrol, is that more or less oil than the maker wants? (c) Which risk is greater in the long run: too little oil or too much?

Four-stroke engine oil

  • Check the oil with the engine off, on level ground: pull the dipstick, wipe it, push it in (as the manual says) and read the level.
  • Fill to the mark, no more. Too much oil can foul the plug and harm the engine.
  • Change oil as often as the manual says. Warm the engine first so the oil drains well, then stop the engine, let the silencer cool, drain into a tray, refit the plug, and refill.
  • Use the oil grade in the manual.

Used oil

Do not pour used oil on the ground, into a drain or into a river. Collect it in a closed container. A Ghana blog says the EPA encourages mechanics to take used oil to designated collection centres; this was not verified with the EPA. Ask the EPA office in Takoradi where to take used oil.

Storing fuel and the engine

  • Storing fuel: see Unit 1 rules (approved container, shade, outdoors, caps tight).
  • For long storage (more than a few weeks), follow the manual: usually close the fuel tap, run the carburettor dry or add stabiliser as the manual says, and keep the engine dry and covered.

SAFETY PROTOCOL: Mixing fuel and changing oil

Before you start

  • Engine off and cool; outdoors; container on the ground; no flame.
  • Marked mixing cup, funnel, clean labelled container, drain tray and used-oil container ready.
  • Ratio read from the manual and written on the container.

While you work

  • Do: measure the oil; add half the petrol, then the oil, shake, then add the rest.
  • Do not: mix in a drink bottle; use mixed fuel in a four-stroke pump engine; drain hot oil.

After you finish

  • Label the mix with ratio and date; close and store it as in Unit 1.
  • Used oil into a closed labelled container; never on the ground or in a drain.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.

Tools and items for this unit

Item What it is and when you use it Size or type
Funnel Pour fuel or oil without spill Clean, fuel only
Marked mixing cup Measure two-stroke oil in ml ml scale
Approved fuel container Mix and store fuel; label ratio and date From the dealer
Drain tray Catch used oil Wide, shallow
Used oil container Hold used oil until taken to a proper place Closed and labelled
Fuel stabiliser Slows stale fuel in storage Dose from the label

Defined in full in Appendix A12.

Fuel and oil tasks

  1. Pour 2 litres of water through a funnel into a container on the ground, with no spill, to practise (no fuel at this step).
  2. With the trainer, mix 2 litres of two-stroke fuel at the maker's ratio. Show your sum on paper first.
  3. Label the container with the ratio and the date.
  4. On a four-stroke engine, check the oil on level ground. Write down the level.
  5. Change the oil on a warm (not hot) engine into a drain tray. Refill to the mark.
  6. Put the used oil in a labelled closed container. Write down where you will take it.

Ask the supplier

Ask a spare-parts or fuel dealer how they advise farmers to mix and store fuel. Write down what they say and compare it with the manual.

Check yourself

  1. Who decides the oil-to-petrol ratio for a two-stroke engine?
  2. How much oil do you need for 4 litres of petrol at 50:1?
  3. Where must you not pour used oil?
05

Unit 4 · Start, run and daily checks

Five minutes of checks before you start saves hours of repair after. A machine that is checked every day rarely breaks on the day you need it.

Competency standard

Learning outcome Performance criteria: the trainee…
4.1 Do the daily checks checks fuel, oil, air filter, tightness, hoses and guards before starting
4.2 Start safely starts and warms an engine using the correct steps; shuts down properly
4.3 Clean the air filter removes, cleans and refits the filter
4.4 Inspect the spark plug removes, inspects, cleans and refits the plug; says what colour tells
4.5 Record keeps a simple service log

Range. Small four-stroke pump engine; the same checks apply to tillers. Evidence. Observation; service log.

Ask a qualified expert. For fuel, fire, exhaust or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. Do not attempt work you are not trained and authorised to do. Never test for a spark with your bare hand.

The daily checklist (engine off and cold)

  • Fuel. Enough clean fuel; no leaks at tank, tap, pipe or carburettor.
  • Oil. On the dipstick, level ground, within the marks.
  • Air filter. Clean and fitted properly.
  • Bolts and covers. Nothing loose; guards in place.
  • Hoses and clamps (pump). Not cracked; clamps tight; strainer on the suction hose.
  • Area. Level firm ground; clear of grass and rubbish around the silencer; open air.
  • Extinguisher and sand within reach.

Starting a small engine (four-stroke pump engine)

Different engines differ. Read your manual first. A typical order is:

  1. Do the daily checklist. Make sure the pump is primed with water if it is a water pump (Unit 5).
  2. Open the fuel tap.
  3. Set the choke as the manual says (usually closed for a cold start).
  4. Turn the engine switch to ON.
  5. Set the throttle a little open.
  6. Hold the machine firmly, pull the cord slowly until you feel resistance, then pull firmly and smoothly. Do not let go of the cord to snap back.
  7. When it starts, open the choke gradually and let it warm up for a short time.
  8. Listen. Look for leaks, smoke, shaking and strange noise.

To stop: reduce the throttle, switch the engine off with the stop switch, close the fuel tap if the manual says so, and stay clear of the hot silencer.

If it does not start after a few pulls, do not keep pulling for ever. Check fuel, switch, choke, and plug cap (Level 2 teaches deeper fault-finding). Flooding with fuel is common: follow your manual.

Cleaning the air filter

A blocked filter makes the engine weak, smoky and fuel-hungry. Dust is the main killer of engines on farms and dusty roads.

  1. Engine off and cold. Remove the cover and take out the filter.
  2. Look at the type. A foam filter can be washed in mild soap and water, squeezed (not twisted), dried fully and lightly oiled as the manual says. A paper filter is tapped gently to shake out dust; do not wash a paper filter unless the manual allows, and replace it if it is dirty or damaged.
  3. Wipe dust out of the housing before refitting. Never let dust fall into the carburettor opening.
  4. Refit tightly. Never run the engine without its filter.

Inspecting the spark plug

  1. Engine off and cold. Pull the plug cap by the cap, not the wire.
  2. Clean dirt around the plug so none falls into the cylinder.
  3. Unscrew with the plug spanner. Look at the tip.
  4. A light brown or grey tip is normal. A black, wet or oily tip means trouble (too rich, too much oil or a dirty filter). A white tip can mean the engine is too lean or too hot. If unsure, ask your trainer or a qualified mechanic.
  5. Brush off light carbon with a small wire brush. Replace the plug if the tip is worn, the porcelain is cracked, or the electrode is burnt.
  6. Check the gap with a feeler gauge. The correct gap and plug type are in your engine's manual. Do not guess.
  7. Screw in by hand first, then tighten gently with the spanner. Over-tightening can damage the cylinder head.
  8. Push the cap on firmly.

The service log

Keep a simple log for each engine: date, hours or days run, what you checked or changed, parts used, cost, and notes. A log tells you when the next service is due and helps you charge fairly.

Date Engine Task Parts used Cost (GH¢) Notes
(example) 4 Nov Pump A Cleaned air filter, checked plug, oil level OK none 0 Plug light brown

Service intervals

A pump engine's manual says to check the air filter every 25 hours of running. A farmer irrigates 3 hours a day, 5 days a week. (a) How many hours does it run in a week? (b) After how many weeks is a filter check due? (c) On very dusty days, should you check sooner?

SAFETY PROTOCOL: Starting, running and servicing a small engine

Before you start

  • Do the daily checklist; engine on level, firm ground in open air.
  • Guards fitted; hoses and clamps checked on a pump; pump primed.
  • PPE: glasses, ear protection, gloves, closed boots.

While you work

  • Do: hold the machine firmly; pull slowly then firmly; stand clear of the silencer.
  • Do not: run it in a closed space (carbon monoxide); keep pulling a flooded engine; run without the air filter.

After you finish

  • Stop switch, wait until it stops, close the tap if the manual says; let it cool before cleaning the filter or plug.
  • Log the work; report leaks, smoke or noise.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.

Tools and items for this unit

Item What it is and when you use it Size or type
Plug spanner and feeler gauge Remove the plug and check the gap See Appendix A1
Wire brush Light carbon off the tip Small
Dipstick Oil level on level ground On the engine
Hour meter or log book Record hours for service intervals Meter or exercise book
Rags and brush Clean the filter housing Clean

Defined in full in Appendix A12.

Daily check, start, filter, plug

  1. Do the full daily checklist on a pump engine. Record it.
  2. Start the engine in the open air (trainer watching, pump primed). Run it for about two minutes, listen, then stop it using the correct shutdown.
  3. When the engine is cold, remove, clean and refit the air filter.
  4. Remove the spark plug, describe its colour and the gap you found, clean it, set or replace it as the manual says, and refit it.
  5. Enter all tasks in your service log.

Watch a service

Watch an experienced mechanic or farmer start and check a pump or tiller. Note each step. How is it the same as, or different from, what you learned?

Check yourself

  1. Name four daily checks.
  2. Why must you never run an engine without its air filter?
  3. What does a black, wet plug tip tell you?
06

Unit 5 · Irrigation pump basics

A pump does not pull water: it lets the air pressure push water in. If it is not full of water to start with, it cannot work, and if it runs dry it can be damaged.

Competency standard

Learning outcome Performance criteria: the trainee…
5.1 Explain how the pump works names pump parts; explains suction and delivery
5.2 Set up the pump places pump, hoses, strainer and clamps correctly
5.3 Prime and run primes the pump and runs it without running dry
5.4 Find simple faults spots air leaks and blockages; says what to check

Range. Small petrol centrifugal pump and hoses; surface water or a tank. Evidence. Pump set-up and run; oral questions.

Ask a qualified expert. For fuel, fire, exhaust, pressure or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. Do not attempt work you are not trained and authorised to do. Never stand in front of a high-pressure delivery hose, never run a pump against a closed delivery for long, and ask a qualified expert before you connect a pump to anything under pressure. Taking water from a river, stream or borehole may need permission: see the end of this unit.

How a centrifugal pump works

Most small farm pumps are centrifugal: the engine turns an impeller, which throws the water outward and pushes it out of the delivery. This lowers the pressure at the centre, so more water comes in through the suction. For this to start, the pump casing must be full of liquid: all centrifugal pumps need liquid in the casing to prime, and if gas or air fills it the pump cannot pump.

Cavitation, a known problem, happens when the suction conditions are too poor for the pump, and it can wear the impeller. You hear it as a rattling or gravel noise. Common causes: a suction hose that is too long, too narrow, kinked, blocked, leaking air, or a pump placed too high above the water. These causes are standard practice; check your pump manual.

Parts of the pump set

Part What it does
Suction hose Brings water in; must be strong enough not to collapse, and airtight
Strainer or foot valve Stops debris and stops water draining back when the pump stops
Priming port Opening to fill the casing with water before starting
Pump casing and impeller Where the water is pushed
Delivery hose or pipe Carries water to the field
Hose clamps Seal the joints

Position and set-up

  • Put the pump as close to the water as is safe and as low as is safe: short, straight, airtight suction gives the best result. Pumps placed below the source level stay primed more easily.
  • Place the pump on firm, level ground, in open air, with fuel stored away from the exhaust.
  • Keep the suction hose short and straight with no kinks and no loops where air can collect.
  • The strainer or foot valve should sit under the water, off the bottom (so it does not suck mud or stones) and away from weeds.
  • Clamp every joint tight. A small air leak on the suction side stops the pump from priming.
  • Fix the delivery hose so it cannot whip about, and keep people away from its end.

Priming and running

  1. Engine off. Open the priming port.
  2. Fill the casing with clean water until it overflows. Fill the suction hose too if you can.
  3. Close the priming port tightly.
  4. Do the daily engine checks (Unit 4). Start the engine as in Unit 4.
  5. Within a short time water should flow. If no water arrives after about a minute, stop the engine, find the air leak or blockage, re-prime and try again.
  6. Never let the pump run dry. The pump relies on the water inside it, and running without water can overheat it and damage the seal. Stop the engine straight away if the water stops.
  7. When you finish, reduce the throttle, stop the engine, and drain the pump if it may freeze or stand for long (the manual says how).

Simple pump faults

Sign Likely cause What to check
No water Not primed; air leak; blocked strainer; foot valve stuck; pump too high Re-prime; check clamps and hose; clear strainer
Water then stops Water level dropped; strainer blocked; hose collapsed Level; strainer; hose
Weak flow Dirty strainer; kinked hose; engine slow; worn impeller Hoses; engine speed; ask a mechanic
Rattling noise Cavitation: long, narrow or leaking suction Shorten and straighten the suction; fix leaks
Engine stalls when pumping Overloaded; delivery blocked; fuel problem Delivery; fuel; filter

Fuel use and cost

A pump uses fuel for the hours it runs. Write the litres used and the hours in your log; it tells you the fuel cost per hour and per field. Use example figures only in your exercises.

Fuel cost of watering

Example figures. A pump uses 1.2 litres of petrol an hour. Petrol costs GH¢15 a litre (example, not a real price). A farmer waters a bed for 2.5 hours. (a) How many litres are used? (b) What is the fuel cost? (c) If the farmer waters 12 times in a season, what is the fuel cost?

Water permission in Ghana

The Water Resources Commission Act 1996 (Act 522) makes it unlawful to divert, dam, store or abstract water resources without authority. The Water Use Regulations 2001 (L.I. 1692) say that abstraction by manual means is exempt (regulation 9). Water abstracted by mechanical means for any purpose where the abstraction level does not exceed five litres per second, and subsistence agricultural use on land not exceeding 1 hectare, are exempt from the permit but must be registered with the District Assembly, which issues a registration number (regulations 10 and 11). Five litres per second is 300 litres per minute. A small pump at full output can pass that line (Appendix A9), so measure your flow. Before you install a pump to take water from a river, stream or underground source for a customer, ask the Water Resources Commission and the District Assembly what applies. The fee schedule in the text read is in 2001 values: current fees are not verified, and the text may have been amended. This is general information, not legal advice; ask a qualified lawyer or the Commission.

Photograph of a petrol water pump set seen from aboveA real petrol water pump set seen from above: an orange fuel tank with a round cap on top, the engine below it, a grey metal pump casing with a round opening on top and two threaded hose connections, standing on a steel frame. 1 2 3 4 5 6 7
A real petrol water pump set seen from above. Find the fuel tank cap, the engine, the pump casing with its round opening on top, the two threaded hose connections and the steel frame. Photo: Anniwinner, Wikimedia Commons, CC BY-SA 4.0.

Photo: parts you can see

No. Part What it does Safety rule
1 Fuel tank cap Closes the petrol tank Refuel only when the engine is off and cool, outdoors; close the cap tightly
2 Engine Turns the pump Very hot when running; keep clear of the cylinder
3 Round opening on the casing The opening used to fill the casing with water before starting (the priming port; check your own pump's manual) Fill only with the engine off; close it tightly before starting
4 Pump casing Metal shell that holds the impeller and guides the water Do not run it dry
5 Threaded hose connection (side) Where a hose is screwed on Clamp the hose; never put a hand in an open port while the engine can turn
6 Threaded hose connection (below) The second hose connection One connection is for suction and one for delivery: read your pump's label before you connect hoses
7 Steel frame Holds the set off the ground Stand the set on firm, level ground so it cannot tip
Labelled petrol irrigation pump set Side view of a petrol pump set beside a water source: strainer, suction hose, hose clamp, connector with sealing washer, pump casing, priming port, impeller, drain plug, discharge port and connector, delivery hose, engine, fuel tank with tap, and stop switch. Petrol irrigation pump set with suction and delivery hoses 1 2 3 4 5 6 7 8 9 10 11 12 13
A petrol irrigation pump set with the strainer, hoses, pump parts and engine numbered. Follow the hose and priming rules in the table.

Parts and safety rules

No. Part What it does Safety rule
1 Strainer (foot valve) Keeps debris out of the pump Fully under water and off the bottom; never run without it
2 Suction hose Brings the water to the pump Reinforced so it cannot collapse; no smaller than the port; as short as possible
3 Hose clamp Seals a hose on its connector Tight on every joint; an air leak stops priming
4 Connector and sealing washer Joins the suction hose to the pump port Washer in good condition or the pump will not prime
5 Pump casing (volute) Shell that guides the water out Do not run it dry
6 Priming port Opening to fill the casing with water Fill with the engine off; close the cap tightly
7 Impeller (inside the casing) Spinning wheel that throws the water out Never put a hand or tool in the ports while the engine can turn
8 Drain plug Empties the casing Open only with the engine off
9 Discharge port and connector Joins the delivery hose Clamp it; the hose must not whip
10 Delivery hose Carries the water to the field Short and wide cuts friction; do not drive over it while running; keep people away from its end
11 Engine Drives the pump All the engine safety rules of Unit 1
12 Fuel tank and tap Fuel for the engine Refuel cool, outdoors; keep fuel away from the exhaust
13 Stop switch Stops the engine Know where it is before starting

SAFETY PROTOCOL: Running an irrigation pump

Before you start

  • Daily engine checks; pump on firm level ground in open air; fuel stored away from the exhaust.
  • Hoses, clamps, sealing washer and strainer checked; casing primed and port closed.
  • Permission to take the water checked (see the end of this unit).
  • PPE: glasses, ear protection, boots.

While you work

  • Do: watch for first water within about a minute; stop if none comes.
  • Do not: run the pump dry; stand in front of the delivery hose end; pump petrol, sea water, acids or chemicals.

After you finish

  • Reduce throttle, stop the engine, let it cool; drain the casing and clean the strainer; coil the hoses.
  • Log hours, fuel and faults.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.

Tools and items for this unit

Item What it is and when you use it Size or type
Suction hose Reinforced, airtight No smaller than the port
Strainer or foot valve Keeps debris out Fully under water
Hose clamps and sealing washer Seal joints against air leaks Match the hose
Priming port and drain plug Fill and empty the casing On the pump
Bucket and stopwatch Time to first water; flow test 20 litres

Defined in full in Appendix A12.

Set up, prime and run a pump

  1. Place the pump near a drum or tank of clean water on firm level ground, in open air.
  2. Connect the suction hose with a strainer; clamp tightly. Keep it short and straight.
  3. Prime: fill the casing and the suction hose with water; close the port.
  4. Do the Unit 4 daily checks, then start the engine with the trainer watching.
  5. Watch the water arrive. Run for five minutes into a second tank. Record the time to first water.
  6. Create an air leak on purpose (loosen one clamp slightly) with the trainer. See what happens and fix it.
  7. Stop the engine, drain, clean the strainer and coil the hoses. Log it.

Find the water

On a farm or garden near you, find where water is taken for irrigation. Describe how it is lifted: bucket, pump, gravity. Measure how far it is from the water to the field, and sketch the set-up.

Check yourself

  1. What must you do before starting a centrifugal pump?
  2. What happens if a clamp on the suction hose leaks air?
  3. Who do you ask about a permit to take water from a river?
07

Unit 6 · Tillers and chainsaws

Both machines make hard work easy and both can injure badly in a second. Learn the safe way first.

Competency standard

Learning outcome Performance criteria: the trainee…
6.1 Prepare safely wears the right protection and checks the machine before starting
6.2 Run a power tiller under supervision starts, walks and stops a tiller in a cleared field
6.3 Understand chainsaw risks says the main chainsaw hazards, including kickback
6.4 Do basic servicing cleans, checks, fuels and stores each machine correctly

Range. Walk-behind power tiller (petrol); petrol chainsaw (demonstration and basic service only at Level 1). Evidence. Observation; oral questions; service log.

Ask a qualified expert. For fuel, fire, exhaust, lifting, sharp-chain or other dangerous work, ask a qualified mechanic or a GhIE-registered engineer. A chainsaw can cause deadly injury. Do not use a chainsaw for cutting at this level. Learn only after proper training from a qualified trainer. For any injury or bleeding, call 112 and see a doctor or nurse.

The power tiller

A power tiller (walk-behind) turns soil using rotating blades or tines at the back. It saves hours of hand digging. Its dangers: rotating tines, strong pull forward, hot engine, noise, and fumes.

Before you start:

  1. Walk the field. Remove stones, wire, roots, rope, plastic and anything that can wind around the tines.
  2. Do the Unit 4 engine checks. Check the gearbox oil if the manual says. Check tines and bolts are tight and the guards are fitted.
  3. Wear closed boots, long trousers, ear protection and safety glasses. No loose clothing.
  4. Keep children, animals and other people well away.
  5. Know the stop switch and the clutch or dead-man lever before you start.

Starting and walking it (supervised):

  1. Put the gear lever in neutral. Start the engine as in Unit 4.
  2. Engage the tines only when ready. Stand behind the handles, feet clear of the tines.
  3. Walk at an even pace, let the machine pull; do not fight it. Keep the machine level.
  4. To turn, disengage drive first. Never reverse towards your feet.
  5. If the tines catch something: stop the engine and wait until the tines stop. Clear it only when stopped.
  6. After use: let the engine cool. Clean soil from the tines, check for loose bolts, wipe the machine, store it dry.

Tiller basic servicing

  • Engine care: same as Units 3 and 4 (fuel, oil, filter, plug).
  • Remove tangled grass and rope from the tine shaft when stopped.
  • Check tine bolts, handlebar bolts and guards each use.
  • Gearbox oil: top up or change as the manual says. Do not guess the grade.
  • Grease points: as the manual says.

The chainsaw: know the danger

A chainsaw has a fast sharp chain, a two-stroke engine and a loud noise. UK guidance for hand-held petrol chainsaws covers fitness to operate, choosing and maintaining the saw, protective equipment, working alone and first aid, and working off the ground.

Facts for awareness:

  • Kickback can happen when the upper tip of the bar touches something or the chain is pinched in a cut, throwing the saw back at the user.
  • The chain brake is meant to stop the chain, and some guidance says to test it before each use and not to use a saw whose brake fails.
  • Protective clothing named in Irish guidance includes steel-toed boots, close-fitting outer clothing, and chainsaw trousers; no protective equipment gives full protection against a chainsaw cut.
  • Never use a chainsaw alone, tired, or when you are not trained.
  • Never climb a ladder or tree with a running chainsaw.

At this level you only learn to look after a chainsaw safely, with the engine off and the chain covered:

  1. Engine off, cold, with the chain guard (scabbard) on.
  2. Clean sawdust from the air filter, around the cylinder fins and the chain brake.
  3. Check the plug, fuel mix (Unit 3: mixed fuel at the maker's ratio) and bar oil.
  4. Look at the chain: broken or blunt teeth are a danger. Do not sharpen yet: Level 2 teaches chain sharpening.
  5. Store with the guard on, fuel drained or as the manual says.

Do not run a chainsaw for cutting in this module. Only a trainer with proper chainsaw training may demonstrate. Trainees watch from a safe distance. If you want to cut timber for a living, take a specialist chainsaw course first. No Ghana chainsaw licence rule was verified: ask the Forestry Commission and the District Assembly about any permit needed to fell or process timber.

Hazard map

Look at the picture or demonstration of a tiller and a chainsaw. List the hazards of each (moving parts, heat, fumes, noise, fuel) and one control for each hazard.

Photograph of a walk-behind rotary tillerA real two-wheel walk-behind tiller in a field: long handlebar with control levers, a red engine on the right with an upright exhaust pipe, a drive casing, one wheel and a tine hood at the front. 1 2 3 4 5 6 7
A real walk-behind rotary tiller. Find the handlebar, the control levers, the engine, the upright exhaust pipe, the drive casing, the wheel and the tine hood at the front. Photo: Green, Wikimedia Commons, CC BY-SA 3.0.

Photo: parts you can see

No. Part What it does Safety rule
1 Handlebar Steers the tiller Hold firmly; keep feet clear of the tines
2 Engine Drives the tiller Start in open air; do not touch it when hot
3 Exhaust pipe Carries the hot exhaust gas out Very hot: keep dry grass and clothing away
4 Drive casing Covers the drive between the engine and the wheel and tines Never run it with the cover removed
5 Wheel Carries the machine Keep feet clear when turning or reversing
6 Tine hood Covers the tines that cut the soil Stop the engine and wait for the tines to stop before clearing anything
7 Control levers Engage the drive and set speed Find the stop control before you start
Labelled power tiller Side view of a walk-behind power tiller: engine, fuel tank, silencer, handlebar, throttle and stop switch, handlebar frame with bolts, dead-man clutch lever, drive belt cover, gearbox, tine shaft with tines, wheel, and tine guard. Walk-behind power tiller, side view 1 2 3 4 5 6 7 8 9 10 11 12
A walk-behind power tiller with the engine, handles, controls, gearbox and tines numbered.

Parts and safety rules

No. Part What it does Safety rule
1 Engine Drives the tiller Unit 1 engine rules; start in open air
2 Fuel tank Holds petrol Refuel cool, outdoors
3 Silencer Quietens the exhaust Very hot: keep dry grass away
4 Handlebar Steers the tiller Hold firmly; keep feet clear of the tines
5 Throttle and stop switch Speed and stop Find the stop switch before starting
6 Handlebar frame and bolts Holds the handles in position Check bolts tight before each use
7 Dead-man (clutch) lever Engages the drive only while held If it does not disengage the drive, do not use the machine
8 Drive belt cover Guards the belt Never run without the guard
9 Gearbox Transmits the drive to the tines Check oil as the manual says; neutral to start
10 Tine shaft and tines Cut and turn the soil Stop the engine and wait for the tines to stop before clearing anything
11 Wheel Carries the machine Keep clear when turning; never reverse towards your feet
12 Tine guard Covers the tines Keep fitted; remove stones and wire first

SAFETY PROTOCOL: Power tiller

Before you start

  • Walk the field and remove stones, wire, roots, rope and plastic.
  • Engine and gearbox checks; tines, guards and bolts tight; stop switch and dead-man lever tested.
  • PPE: closed boots, long trousers, glasses, ear protection; no loose clothing; people and animals well away.

While you work

  • Do: neutral to start; engage the tines only when ready; walk at an even pace.
  • Do not: reach for tangled tines while the engine runs; reverse towards your feet; let children near.

After you finish

  • Stop the engine; wait until the tines stop; let it cool; clean the tines and check bolts; store dry.
  • Report a lever that does not release, a loose bolt or a leak.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
Photograph of a chainsawA real yellow chainsaw standing on a log: a long guide bar with the chain on its edge, a black wrap-around front handle, a recoil starter cover with a cord handle, a filler cap on top and a black rear handle. 1 2 3 4 5 6
A real chainsaw, shown with the engine off. Find the guide bar, the chain on its edge, the front handle, the starter cover, the filler cap on top and the rear handle. Photo: Arp, Wikimedia Commons, CC0.

Photo: parts you can see

No. Part What it does Safety rule
1 Guide bar Carries and guides the chain Keep the cover on when not cutting
2 Saw chain Cuts the wood Sharp: handle only with gloves and the engine off
3 Front handle Second hand grip Keep the thumb wrapped round it
4 Starter cover Covers the pull-cord starter Start only on firm ground, as trained
5 Filler cap Closes a tank (check the manual for fuel or chain oil) Never mix up the fuel and chain-oil caps; refuel cool and outdoors
6 Rear handle Holds the saw with the throttle hand Both hands on the handles when a trained operator cuts
Labelled petrol chainsaw Side view of a petrol chainsaw: rear handle, front handle, throttle trigger with lock, chain brake hand guard, fuel and bar-oil caps, chain tensioner and bar nuts, silencer, guide bar, bar tip kickback zone, saw chain, spiked bumper, chain catcher, and engine cover with starter and air filter. Chainsaw, side view (engine off, chain guard removed) 1 2 3 4 5 6 7 8 9 10 11 12 13
A chainsaw with its main parts numbered. At Level 1 you only learn these parts with the engine off and the chain guard on.

Parts and safety rules

No. Part What it does Safety rule
1 Rear handle Holds the saw with the throttle hand Both hands on the handles when a trained operator cuts
2 Front handle Second hand grip Keep the thumb wrapped round it
3 Throttle trigger and trigger lock Set engine speed The lock prevents accidental opening
4 Chain brake hand guard Stops the chain when pushed or in kickback Test the brake before each use; do not use a saw whose brake fails
5 Fuel and bar-oil caps Fill points for mixed fuel and chain oil Do not mix them up; refuel cool and outdoors
6 Chain tensioner and bar nuts Hold the bar and set chain tension Adjust only with the engine off and cool
7 Silencer Quietens the exhaust Very hot
8 Guide bar Carries and guides the chain Keep the scabbard on when not cutting
9 Bar tip (kickback zone) The upper tip of the bar Contact here can throw the saw back
10 Saw chain Cuts the wood Sharp and dangerous: handle with gloves, never with the engine on
11 Spiked bumper Grips the wood as a pivot Keep in contact as trained
12 Chain catcher Catches a broken chain Check it is not damaged
13 Engine cover, starter and air filter Covers the engine, starter and filter Clean sawdust from the filter and fins with the engine off

SAFETY PROTOCOL: Chainsaw care (engine off) and demonstration

Before you start

  • Engine off and cold, plug cap understood, chain guard (scabbard) on.
  • PPE: gloves, glasses, ear protection, steel-toe boots; chaps for the trained demonstrator.
  • Never alone; trainees do not cut at Level 1.

While you work

  • Do: clean fins and filter; check plug, fuel mix and bar oil; look at the chain.
  • Do not: start the saw yourself; touch the chain edge; work tired; sharpen yet.

After you finish

  • Guard on; store with fuel drained or as the manual says; log the care.
  • Report a cracked chain, loose cover or brake fault; do not use the saw.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.
  • Heavy bleeding: press on the wound with a clean cloth and call 112.

Tools and items for this unit

Item What it is and when you use it Size or type
Safety glasses, ear protection, boots, long trousers Tiller work As Unit 1
Spanners Tine, handle and guard bolts Metric
Chain guard (scabbard) Cover on the chain when not cutting Fits the bar
Bar and chain oil Separate chain lubricant From the maker
Brush Clean sawdust from filter and fins Small

Defined in full in Appendix A12.

Tiller walk-round and chainsaw care

  1. Walk the practice field with the trainer and remove hazards. Record what you removed.
  2. Do the pre-start checks on the tiller (fuel, oil, gearbox, tines, guards) and record them.
  3. Start the tiller under the trainer's eye. Walk it along one straight strip. Stop it correctly.
  4. Cool the machine, clean the tines and check bolts.
  5. On a chainsaw with the engine off and the guard on: clean the air filter and fins, check the plug, and describe the chain condition. Do not start it.
  6. Log all tasks.

Who uses them near you?

Find a farmer, a carpenter or a land clearer who uses a tiller or chainsaw. Ask what the worst accident or breakdown they have seen was, and how it could have been avoided.

Check yourself

  1. What must you do before clearing grass from tiller tines?
  2. Name one chainsaw danger.
  3. Why must you learn chainsaw cutting with a trained instructor, not alone?
08

Unit 7 · Your location, business and brand

Farmers will pay for a mechanic who arrives, fixes it right and tells the truth about the cost. Start small, do clean work and keep records.

Competency standard

Learning outcome Performance criteria: the trainee…
7.1 Choose a place and service picks a location and a small set of services
7.2 Cost a job lists parts, fuel, time and profit and gives a clear price
7.3 Register and keep records names the first registration steps and keeps job records
7.4 Market yourself makes a simple plan using WhatsApp, a sign and referrals

Range. A one-person mobile or small-shop servicing business. Evidence. Costed quotes; job records; business plan.

Ask a qualified expert. This is general information, not legal advice. Ask a qualified lawyer before you act on any legal, licence or registration matter. For tax, VAT, PAYE and SSNIT, check with GRA or a qualified accountant before you act. For loans and insurance, ask your bank, a licensed insurer or a qualified accountant. For fuel, fire, exhaust, pressure and other dangerous work, ask a qualified mechanic or a GhIE-registered engineer.

Where to work

  • Near farms. Irrigated vegetable farms need pump servicing and fuel; farmland edges and market-garden areas are good places for a small shop or a mobile service. Ask local farmers where pumps and tillers are used most.
  • Mobile service. Many pump jobs are on the farm. A mobile mechanic with a toolbox and spare plugs, filters and clamps can start without renting a shop.
  • A small roadside or yard workshop. Good if it has shade, a firm floor, a place for spares, and open air for test running. Never run engines in a closed room.
  • Ask your landlord and the District Assembly about use of the space; STMA runs a business operating permit portal. Fees for an engine and pump repair workshop: not verified.

Services that sell

  • Pump servicing: filter, plug, oil, fuel and priming.
  • Hose, clamp and strainer supply and fitting.
  • Tiller servicing and tine repairs (simple).
  • Chainsaw care (cleaning, fuel mix advice), with sharpening after Level 2.
  • Simple "farm engine service day" visits for groups of farmers, and service packs for the season.
  • Selling spares: plugs, filters, clamps, oil. Buy from reputable dealers and avoid unknown parts.

Costing a job

Add up: parts + fuel and consumables + travel + your time + profit. Take a deposit for parts before buying them.

Price a pump service

Example figures. Parts: spark plug GH¢25, air filter GH¢40, oil GH¢60. Consumables (cleaner, rags) GH¢10. Travel GH¢20. Your time: 2 hours at GH¢40 an hour. (1) Total cost? (2) Price for a 20% margin on price? (3) If the customer pays a 50% deposit for parts first, how much is the deposit if parts are GH¢125?

Registering and records

  • Register a business name at the Office of the Registrar of Companies: GH¢130, then GH¢70 a year to renew (2026 fees). Your Ghana Card number is your tax number (TIN).
  • STMA's 2025 fee-fixing resolution lists business operating permit fees by trade. The fee for engine and pump repair was not verified; ask STMA.
  • The STMA says master artisans must register their trainees. If you take an apprentice, register them.
  • Keep a job record book: date, customer, machine, work done, parts, price, paid or not.

Marketing yourself

  • WhatsApp Business. A free profile with your name, services, area and a short catalogue. Send the farmer a message with what you found and a photo of the old filter.
  • A sign at your workshop or on your toolbox: your name, "Pump and engine servicing".
  • Referrals. Ask every happy farmer to tell two neighbours.
  • A portfolio. Before and after photos (with permission), kept on your phone.
  • Be honest. Tell the farmer what is wrong and what it will cost before you start. Do not replace parts that are not faulty.

Accessibility note

The Persons with Disability Act 2006 protects the rights of persons with disability. Many tasks in this trade can be done seated or with adjustments: bookkeeping, quoting, customer service, parts selling, WhatsApp marketing, and bench servicing of small parts (filters, plugs, carburettor cleaning on a bench). Tasks involving carrying machines, pulling starter cords, or walking behind a tiller are harder; helpers or adjusted tools can help. Ask your Assembly about disability support; the hub's inclusion modules explain more. (Details and funding: not verified here.)

SAFETY PROTOCOL: Mobile service visit on a farm

Before you start

  • Tell someone where you are going; tools and spares checked; first-aid kit and extinguisher in the kit.
  • Agree the job and the price before you start; take the deposit for parts.
  • PPE: glasses, gloves, boots, ear protection.

While you work

  • Do: work in open air, engine off and cool; photograph before and after.
  • Do not: work alone on a running engine; use the customer's fuel store carelessly; leave used oil behind.

After you finish

  • Test run in the open; clean up; take away used oil and parts; write the job record and receipt.
  • Tell the customer what you found and what to check daily.

Emergency

  • Call 112 for fire, serious burn, heavy bleeding, collapse or poisoning.
  • Fire: get people clear; use the extinguisher or sand only if it is safe; never throw water on a petrol fire. A doctor or nurse must advise on first aid.
  • Switch the engine off at the stop switch; move anyone who feels dizzy or sick to fresh air (carbon monoxide).
  • Electrical or battery isolation: not needed on a pull-start engine; for any electric item, isolate at the supply and call a certified electrician.

Tools and items for this unit

Item What it is and when you use it Size or type
Job record book and receipt book Record every job and payment Exercise book
Phone with WhatsApp Business Messages, catalogue, photos Smartphone
Toolbox with spare plugs, filters, clamps Mobile service From dealers

Defined in full in Appendix A12.

Quote and plan

  1. Choose one service. Write a full cost sheet and a price.
  2. Write a one-page business plan: where you will work, services and prices, tools and cost (use example prices), first customers, how you will market, registration step.
  3. Draft a WhatsApp Business profile text and a sign.
  4. Present your plan to the class.
  5. Start a job record book today.

Talk to a mechanic

Ask a working small-engine or pump mechanic how they find customers, price jobs, and what they wish they had known when they started. Collect three prices (a plug, a filter, a hose clamp) from different shops, and write them down.

Check yourself

  1. Name the five parts of a job price.
  2. Where do you register a business name?
  3. Why take a deposit?
09

Appendix A · Reference layer: cards, tables and forms

Keep this part on the bench. Every figure here names the engine or the source it comes from. Your own engine's manual always wins. Where a number was not found, the cell says so.

Ask a qualified expert. The tables and cards in this appendix cover fuel, fire, exhaust, pressure, water-use law and first aid. They are for awareness and quick look-up, not a replacement for training. For fuel, fire, exhaust, pressure or other dangerous work ask a qualified mechanic or a GhIE-registered engineer; for any injury, burn, poisoning or illness see a doctor or nurse and call 112 in an emergency; for law and permits ask the named office or a qualified lawyer. This is general information, not legal advice.

A1. Typical values card

How to read it. The left columns are the figures printed in the Honda owner's manual for the WB20XT and WB30XT water pumps (a US manual, read in full on 20 Nov 2026). They are typical for those two models, not universal. Many pumps sold in Ghana use other engines, including copies. Write your own engine's figures in the blank column from its own manual.

Item Honda WB20XT (GX120 engine) Honda WB30XT (GX160 engine) Your engine
Spark plug gap 0.70 to 0.80 mm (0.028 to 0.031 in) 0.70 to 0.80 mm (0.028 to 0.031 in)
Plug spanner size 13/16 in 13/16 in
Engine oil SAE 10W-30, API service category SJ or later, for general use same
Oil quantity 0.56 L (0.59 US qt) 0.58 L (0.61 US qt)
Fuel tank 2.0 L 3.1 L
Idle speed 1,400 rpm, plus or minus 150 1,400 rpm, plus or minus 150
Pump ports 50 mm (2 in) 80 mm (3 in)
Smallest suction hose allowed 50 mm (2 in), reinforced 80 mm (3 in), reinforced
Maker's best-case total head 28 m 26 m
Maker's best-case suction head 8 m 8 m
Maker's best-case flow 575 L per minute 1,041 L per minute
Self-priming time at 5 m suction 110 seconds 150 seconds

The word "maximum" is a best case. Honda's figures are the most the pump can do under test conditions. A real job always gives less (see the hose rules in A6 and Level 2 Unit 4). Other dealer listings of similar pumps quote different heads for the same size, which shows that maximum figures depend on the test, so use the figures in your pump's manual.

Other Honda rules from the same manual. Plug: tighten by hand first, then a little with the wrench, to compress the washer. A 100-hour spark arrester clean applies where one is fitted. Never pump petrol or other flammable liquids, sea water, acids or chemical solutions with the pump.

Valve clearance, torque and compression. Not given in this book at Level 1 (Level 2 shows what Honda prints for these two engines and where sources disagree). Fastener torque: no open source found; use the shop manual for your engine.

A2. Honda maintenance schedule: the items to know

The Honda WB manual lists these items, each to be done "at every indicated month or operating hour interval, whichever comes first":

Item What the manual says to do
Engine oil Check the level; change it
Air cleaner Check; clean (more often in dusty places)
Spark plug Check and adjust; replace
Spark arrester (where fitted) Clean (every 100 hours)
Sediment cup Clean
Idle speed Check and adjust (dealer job)
Valve clearance Check and adjust (dealer job)
Combustion chamber Clean (dealer job)
Fuel tank and filter Clean (dealer job)
Fuel tube Check every 2 years; replace if necessary (dealer job)
Impeller, impeller clearance, pump inlet valve Check (dealer job)

The manual also says that for commercial use you should log the hours of operation to find the right service interval. The hour figures for each item are in your own manual: copy them into your service log.

A3. Two-stroke mixing chart

The maker's ratio only. Millilitres of two-stroke oil to add to the petrol. Worked from oil = 1,000 ml per litre of petrol divided by the ratio number (arithmetic, checked by script). Use the ratio printed in your saw or tiller manual.

Petrol 25:1 32:1 40:1 50:1
1 litre 40 ml 31 ml 25 ml 20 ml
2 litres 80 ml 62 ml 50 ml 40 ml
5 litres 200 ml 156 ml 125 ml 100 ml
10 litres 400 ml 312 ml 250 ml 200 ml
20 litres 800 ml 625 ml 500 ml 400 ml

The 32:1 cells are rounded down to whole millilitres. Measure with a marked cup. Mix no more than you will use in the time the manufacturer allows: one manual says 30 days, or 60 days with stabiliser.

A4. Quick cards (copy each onto one page and pin it up)

Card 1 · Safety. Engine off and cool to refuel. Outdoors only. Container on the ground. No flame, no smoking. Wipe spills and let them dry. Silencer stays hot: do not touch. Ear protection, glasses, gloves, closed boots. Nothing loose that can be pulled in. Extinguisher and sand within reach. Call 112 for fire, burns, bleeding or poisoning.

Card 2 · Daily check (engine off, cold). Fuel enough and clean, no leaks. Oil on the dipstick between the marks, ground level. Air filter clean and seated. Bolts and guards tight. Hoses, clamps, strainer in place. Silencer area clear of grass. Extinguisher and sand in reach.

Card 3 · Start and stop (typical order, read your manual). Daily check. Pump primed. Fuel tap on. Choke as the manual says. Switch ON. Throttle a little open. Slow pull to resistance, then firm and smooth, never let the cord snap back. Open choke slowly, warm up, listen and look. To stop: throttle down, stop switch, fuel tap off if the manual says, stay clear of the silencer.

Card 4 · Prime and run a pump. Engine off. Open priming port. Fill casing until it overflows, fill the suction hose if you can. Close the port tightly. Strainer completely under water and off the bottom. Every clamp tight; sealing washer in the connector. Start. No water after about one minute: stop, find the air leak or blockage, re-prime. Never run dry. Honda also says never run the pump without the strainer.

Card 5 · Storage. Short (days): tap off, covered, dry, upright. Long (weeks): follow your manual, usually close the fuel tap, run the carburettor dry or add stabiliser as the label says, keep dry and covered. Pump: drain the casing. Never store petrol indoors where people live.

Card 6 · Emergency. Fire: get everyone clear, use the extinguisher or sand only if safe, call 112. Do not throw water on a petrol fire. Dizzy, headache or sick near an engine: switch off, move everyone to fresh air, get medical help, call 112. Burn: cool with clean running water and get medical help. Bleeding: press with a clean cloth and call 112. A doctor or nurse must check all first-aid advice (see the expert line above).

The advice not to use water on a petrol fire, and to prefer dry powder, carbon dioxide or foam extinguishers for flammable-liquid fires, comes from UK fire-safety guidance, not from Ghana: ask the Ghana National Fire Service which extinguisher to buy.

A5. One-page troubleshooting chart (check the cheap and common first)

Engine will not start or runs badly. Based on the Honda WB manual chart, rewritten in order of cost.

Order Check Cheap test Fix
1 Fuel tap off, switch off, choke wrong Look and touch Set tap ON, switch ON, choke closed if cold
2 Out of fuel Look in the tank Refuel (Unit 3)
3 Bad or old fuel; water or dirt in fuel Smell; jar test in A8 Drain tank and carburettor, refuel with fresh petrol
4 Plug fouled, wet or wrongly gapped Remove and look (Unit 4) Clean, set gap, or replace; dry a wet plug and start with throttle fully open
5 Sediment cup or fuel filter clogged Look for dirt or water Clean or replace
6 Air filter clogged Look Clean or replace
7 Throttle left on slow (engine lacks power) Look at the lever Move to fast
8 None of the above Take it to a qualified mechanic or Honda dealer (Level 2)

Pump: no or low water.

Order Check Fix
1 Pump not primed Fill casing, re-prime
2 Strainer not completely under water, or clogged Sink it, clean it
3 Air leak at connector (missing or damaged sealing washer, loose clamp) Replace washer, tighten connector and clamp
4 Suction hose collapsed, cut or punctured, or too small or too long Replace with reinforced hose, no smaller than the port, as short as possible
5 Delivery hose damaged, too long or too small Replace
6 Pump too high above the water (excessive or marginal head) Move the pump or hoses to lower the head
7 Engine lacks power Use the engine chart above

A6. Pump set-up picture-checklist (words for your own sketch)

  • Pump close to the water, on firm level ground, in open air
  • Suction hose reinforced (will not collapse), no perforations, no smaller than the pump port, as short as possible
  • Sealing washer inside the suction connector, in good condition; clamp on the connector
  • Strainer fitted on the far end, fully under water, off the bottom, clear of weeds
  • Delivery hose short and wide where possible: a long or narrow hose cuts the output
  • Delivery hose clamped and fixed so it cannot whip; do not drive over it while running
  • Suction head the shorter part of the total head

A7. Units and the flow test

To change Rule
litres per second to litres per minute multiply by 60
litres per second to cubic metres per hour multiply by 3.6
litres per minute to litres per second divide by 60
bar to metres of head multiply by about 10.2
1 US gallon about 3.785 litres
1 inch 25.4 mm

These are standard conversions, checked by arithmetic; confirm with a GhIE-registered engineer for design work.

Bucket and stopwatch flow test. (1) Use a bucket of known size, for example 20 litres (check it by filling with a measured jug). (2) Put the end of the delivery hose into the bucket and start the stopwatch. (3) Stop when it is full. (4) Flow in litres per second = bucket litres divided by seconds. Example (not measured): 20 litres in 4 seconds is 5 litres per second, which is 300 litres per minute. Repeat three times and average.

A8. Fuel quality quick tests and a Ghana warning

Why it matters. Ghana's petrol standard is called GS 140 and its diesel standard GS 141 (editions and limits not verified at the standard itself: ask the Ghana Standards Authority); the NPA and the Authority have reviewed the national petrol standard. Even so, reports describe premix and kerosene being blended into petrol at some outlets, and the NPA has said that selling premix as petrol is a crime. The reports link adulterated fuel to engine failures and breakdowns. Premix is subsidised petrol with oil, dyed, meant for fishermen's outboard motors: do not use it as a plain fuel in a four-stroke pump engine, and do not assume its oil ratio suits your saw.

Bench tests (general good practice; not a Ghana standard; ask a qualified mechanic):

Test How What it can tell you
Jar test Pour a sample into a clean clear glass jar and let it stand 10 minutes Water or dirt settles at the bottom; the fuel should be clear
Smell Smell the sample (outdoors, do not breathe deeply) A sour or varnish smell means old fuel; a kerosene smell means a wrong fuel
Colour Hold the jar to the light Premix is dyed; plain petrol is normally clear or lightly coloured
Carburettor look When you strip a carburettor, look for gum, jelly or water in the bowl Gum means old or poor fuel

If you suspect bad fuel: do not use it, keep a sample in a labelled closed container, keep your receipt, and report to the NPA.

A9. Ghana notes: who to ask

Question What the sources say Who to ask
Do I need a permit to pump water from a river or stream? L.I. 1692 regulation 9 exempts abstraction by manual means. Regulation 10 exempts from the permit water abstracted by mechanical means for any purpose where the abstraction level does not exceed five litres per second, and subsistence agricultural use on land up to 1 hectare; those uses must still be registered with the District Assembly (regulation 11), which issues a registration number. Water Resources Commission; your District Assembly
Does my pump go over five litres per second? A pump's full output can. The WB20XT's best-case 575 L per minute is 9.6 L per second, and the WB30XT's 1,041 L per minute is 17.3 L per second. Measure the real flow with the bucket test (A7): real flow on a job is lower than the maker's best case. Water Resources Commission
Fees and the current text The fee schedule in the copy read is in 2001 values: current fees not verified. The copy read is a text copy; the regulations may have been amended. Water Resources Commission
Selling or storing fuel Commercial storage and sale of petroleum needs an NPA licence; small farm quantities: not verified NPA; Ghana National Fire Service
Used oil Collection points in Takoradi: not verified EPA Western Regional office
Chainsaws A news report says the ban on chainsaw lumber milling is still in force; which regulation is current is not verified. Never use a saw to mill lumber. Forestry Commission; District Assembly

A10. Mistake catalogue (the common ones, from the manual and from general practice)

  1. Running the pump dry: the seal and casing can be damaged (Unit 5).
  2. A suction hose that collapses (not reinforced) or is too small or too long (Honda WB manual rule).
  3. A strainer that is not fully under water, or none at all.
  4. A loose clamp or a missing sealing washer: an air leak stops priming.
  5. Refuelling a hot engine, or near a flame.
  6. Mixed fuel in a four-stroke pump engine, or plain petrol in a two-stroke saw.
  7. A guessed oil ratio: always the maker's.
  8. Storing petrol in a drink bottle or in the house.
  9. Old fuel left in the tank and carburettor: the Honda manual lists bad stored fuel as a cause of no start and low power.
  10. Running an engine in a closed shed (carbon monoxide).
  11. Pulling the cord for ever on a flooded engine instead of drying the plug.
  12. Running without the air filter.
  13. Touching the governor or the top-speed screw.
  14. Using the wrong spanner and rounding the bolt.

A11. Blank forms (copy into your exercise book)

Engine card (one per machine)

Item Entry
Owner
Machine type (pump, tiller, saw)
Engine make and model
Serial number
Plug type and gap (from the manual)
Oil type and quantity (from the manual)
Fuel (petrol or mixed, ratio)
Date bought or first seen

Fuel and hours log

Date Hour meter or hours run Litres added Task done Initials

To find litres per hour: fill the tank to the same mark before a run, run for a measured time, then refill to the mark and measure the litres added. Litres divided by hours is your own measured figure.

Service log: as in Unit 4 (date, engine, task, parts used, cost in GH¢, notes).

Job record: date, customer, machine, work done, parts, price, deposit paid, balance, signed.

Storage card: machine, date stored, fuel drained or stabilised (circle), plug and cylinder oiled as the manual says (circle), drained pump (circle), cover fitted (circle), stored by.

Skills tick-list (trainer signs and dates): safe refuel; mixes 2-stroke fuel; checks and changes oil; cleans air filter; inspects and gaps a plug; starts and stops safely; primes and runs a pump; finds a simple pump fault; completes a service log.

A12. Tools and Items Glossary

Every tool, part and material used in this book is named and explained here. Also called: other common English or trade names. Local names for tools differ from town to town. Use the standard name given here when you order or ask for help, and show the picture. Cost class: cheap, medium or dear (no prices). Size or type: only what a source or the maker gives; otherwise "from the maker or dealer".

Item What it is and what it does Size or type Also called Used in
Spanner set (wrench) Metal tools that turn nuts and bolts; ring ends grip best, open ends reach Metric; the right size for each bolt wrench set, open and ring spanners U2
Socket set Cups that fit over a nut, turned by a ratchet handle Metric; from the maker or dealer ratchet set, socket wrench set U2
Plug spanner (plug wrench) A deep socket or tee-bar made to turn spark plugs without damaging the porcelain Must match the plug; Honda WB manual: 13/16 in spark plug socket, plug key, tee-bar plug wrench U2, U4
Screwdrivers (flat, cross) Turn screws; use the right tip so the head is not damaged Several sizes slotted and Phillips screwdrivers U2
Pliers Grip, hold or bend small parts General combination pliers, grips U2
Feeler gauge Thin steel blades of known thickness; slide between two surfaces to measure a gap, such as the plug gap Blades in mm or inches; gap from the manual thickness gauge, gap gauge, feeler blades U2, U4
Wire brush Stiff brush to clean carbon off a plug tip lightly Small steel brush, plug brush U4
Small paintbrush Brushes dust off an air filter housing or fins Small cleaning brush, soft brush U2
Rags Wipe oil and dust; keep clean ones for fuel work Cotton wiping cloths, wipes U1
Funnel Guides fuel or oil into a small opening without spilling Clean; keep one for fuel only filling funnel U1, U3
Drain tray Catches used oil when you drain it Wide and shallow oil pan, drip tray U3
Marked mixing cup A cup with a millilitre scale to measure two-stroke oil; a bottle cap is not a measure Millilitre scale measuring cup, oil measure, mixing bottle U3
Approved fuel container A strong, closed container made for petrol, with a tight cap, labelled petrol or mixed fuel. Ghana standard for "approved": not verified From the maker or dealer jerrycan, petrol can, fuel can U1, U3
Fire extinguisher A cylinder of extinguishing agent for small fires; the type for petrol must be confirmed with the Ghana National Fire Service Type from GNFS extinguisher, dry powder extinguisher U1
Sand bucket A bucket of dry sand to smother a small spill fire About 10 litres fire bucket U1
First-aid kit A box of dressings and basic supplies for small injuries From a pharmacy first aid box, medical kit U1
Safety glasses Protect the eyes from dust, chips and splashes Clear, close fitting safety goggles, eye protection U1
Ear protection Ear plugs or muffs to lower engine noise; no Ghana noise figure found Plugs or muffs ear muffs, ear plugs, hearing protectors U1
Gloves Protect hands from heat, oil and rough parts; never near a running belt or chain Fit the hand work gloves, hand protection U1
Closed boots Protect feet from dropped parts, hot metal and tine contact Steel toe cap is best for saw work safety boots, work boots U1
Fuel tank Holds the fuel; has a cap with a vent so fuel can flow From the maker petrol tank, gas tank U2
Fuel tap (fuel valve) The lever that opens and closes the flow of petrol to the carburettor On the tank or carburettor fuel cock, fuel valve, petcock U2
Sediment cup A small glass or metal cup under the fuel tap that traps water and dirt; wash it with a non-flammable solvent Honda lists it as a service item fuel bowl, sediment bowl, trap cup U2
Carburettor The part that mixes fuel with air From the maker carburetor, carb U2
Choke A flap or lever that gives a richer mix for a cold start From the maker choke lever, starter flap U4
Air filter (air cleaner) A foam or paper element that stops dust entering the engine Foam or paper; from the maker air cleaner, filter element U4
Spark plug Makes the spark that ignites the fuel and air mix Type and gap from the manual plug, sparking plug U4
Plug cap and lead The rubber cap and wire that carry the high voltage to the plug Pull the cap, not the wire spark plug boot, HT lead, plug wire U4
Recoil starter (pull cord) A spring-loaded rope that turns the engine by hand to start it From the maker pull starter, rope starter, recoil assembly U4
Flywheel A heavy wheel on the crankshaft that stores energy and carries magnets that help make the spark From the maker magneto wheel, rotor U2
Ignition coil (magneto) Makes the high voltage for the plug from the spinning magnets From the maker magneto, coil, ignition module U2
Stop switch (kill switch) Grounds the ignition so the engine stops On the handle or engine kill switch, ignition switch, engine stop U4
Cylinder and piston The tube and the moving plug in it, where the fuel burns and pushes From the maker cylinder block, piston assembly U2
Crankcase and sump The housing for the crankshaft and (four-stroke) the engine oil From the maker engine block base, oil sump U2
Oil filler and dipstick The opening for oil and the rod that shows the level Read on level ground oil cap, oil level stick U3
Silencer (muffler) Quietens the exhaust; stays very hot after stopping From the maker muffler, exhaust box U1
Spark arrester A screen in the silencer that stops sparks; Honda says to clean it every 100 hours where fitted Optional on the WB pumps spark screen, exhaust screen A2
Throttle The lever that sets engine speed From the maker throttle lever, speed lever, accelerator U4
Governor A part that keeps the engine speed steady; do not adjust From the maker speed governor, speed regulator U2
Cooling fins and fan cover Metal fins and a fan that blow air over the engine; keep them clean From the maker cylinder fins, blower housing, shroud U6
Engine oil (four-stroke) Lubricates the engine; Honda WB manual: SAE 10W-30 for general use SAE grade and API class from the manual motor oil, 4-stroke oil, SAE 10W-30 U3
Two-stroke oil Oil made to be mixed into the petrol; never used alone Grade and ratio from the maker 2-stroke oil, 2T oil, mixing oil U3
Fuel stabiliser An additive that slows petrol going stale in storage; follow the label dose From the label fuel stabilizer, fuel preserver U3
Gearbox oil Heavy oil in a tiller gearbox; grade from the manual From the manual gear oil, transmission oil U6
Grease Thick lubricant for grease points; as the manual says From the manual lubricating grease U6
Used oil container A closed, labelled container to hold drained oil until you take it to a proper place Closed, labelled waste oil drum, oil can U3
Centrifugal pump A pump with a spinning impeller that throws water outward From the maker water pump, surface pump, self-priming pump U5
Pump casing (volute) The shell around the impeller that guides the water out From the maker pump body, pump housing, volute U5
Impeller The spinning vane wheel in the pump; Honda lists impeller and impeller clearance as dealer checks From the maker pump wheel, rotor, vane wheel U5
Mechanical seal A seal where the shaft enters the casing; ruined by dry running From the maker pump seal, shaft seal U5
Priming port The opening used to fill the casing with water before starting From the maker fill port, priming plug, filler plug U5
Drain plug A plug at the bottom of the casing to empty it From the maker drain screw, drain bolt U5
Suction port and discharge port The pump openings for the hoses; Honda WB20XT 50 mm, WB30XT 80 mm From the maker inlet and outlet, intake and delivery port U5
Suction hose Reinforced hose that will not collapse; no smaller than the pump port Reinforced, no perforations inlet hose, reinforced hose, spiral hose U5
Delivery hose (discharge hose) Carries water away from the pump; short and wide cuts friction Commercial hose discharge hose, outlet hose, layflat U5
Hose connector The fitting that joins a hose to the pump port Matches port hose tail, nipple, hose coupling U5
Sealing washer A rubber washer in the suction connector that stops air leaks Replace if missing or damaged rubber washer, gasket washer U5
Hose clamp A band with a screw that squeezes a hose onto a connector Matches hose worm-drive clip, jubilee clip, hose clip U5
Strainer (foot valve) A screen on the suction end that stops debris; a foot valve also holds water in the hose Fitted fully under water suction strainer, foot valve, intake screen U5
Tiller tines (blades) The rotating blades that break the soil From the maker rotary blades, tines, cultivator blades U6
Tine shaft The shaft that carries the tines; grass and rope wind round it From the maker blade shaft, rotor shaft U6
Dead-man (clutch) lever A handlebar lever that stops the drive when released From the maker clutch lever, safety lever, operator presence lever U6
Chain The loop of cutting links on a chainsaw Pitch and gauge from the saw maker saw chain, cutting chain U6
Bar The flat guide the chain runs round Length from the maker guide bar, saw bar U6
Chain brake A band that stops the chain when the guard is pushed; test before each use From the maker kickback brake, hand-guard brake U6
Scabbard (chain guard) A cover for the bar and chain when not cutting Fits the bar bar cover, chain cover, bar guard U6
Bar and chain oil A separate sticky oil that lubricates the chain; not mixed into the fuel From the maker chain oil, bar oil, chain lubricant U6
Chaps (chainsaw trousers) Leg protection with layers that can clog a chain; no gear gives full protection From the supplier chainsaw chaps, leg guards U6
Hour meter A counter of engine running hours; the basis of service intervals Fitted or portable hour counter, running-hours meter A2
Stopwatch Times priming and flow tests Phone or watch timer, phone timer U5
Bucket (flow test) A bucket of known volume for the flow test 20 litres is easy measuring bucket, calibrated bucket A7
Job record book and receipt book Books for jobs, prices and receipts Exercise book job book, receipt pad U7

Items to learn at Level 2. Compression tester, spark tester, leak-down tester, torque wrench, round file and file holder, depth-gauge tool and the diesel parts are defined in Level 2.

10

Glossary

Term Meaning
Air filter Keeps dust out of the engine
Carbon monoxide (CO) A poisonous gas in exhaust that you cannot smell
Carburettor Mixes fuel and air
Cavitation Damage and noise when a pump cannot get enough water in
Centrifugal pump A pump that throws water outward with a spinning impeller
Choke Makes the mix richer for a cold start
Competent / Not Yet Competent The two possible results of a CBT assessment
Impeller The spinning part inside a pump
Kickback A sudden backward jump of a chainsaw
Priming Filling the pump with water before it starts
Silencer (muffler) Part that quietens the exhaust; very hot
Spark plug Makes the spark that lights the fuel
Strainer / foot valve Stops debris and keeps water in the suction hose
Two-stroke An engine with a power stroke every turn; oil mixed in the fuel
11

Logbook

Copy these pages into an exercise book. Your logbook is part of your assessment evidence.

  • Unit 1: safety set-up checks; sketch of the workshop and exits
  • Unit 2: parts drawing; engine make and model; manual notes
  • Unit 3: fuel mix sums and labels; oil check and change; used-oil plan
  • Unit 4: daily checklists; filter and plug records; service log
  • Unit 5: pump set-up sketch; time to first water; faults found
  • Unit 6: hazard map; tiller checks; chainsaw care record
  • Unit 7: cost sheets; job record book; business plan; prices collected
  • Every homework, dated
12

Self-check quiz

  1. Name three rules for handling petrol.
  2. Why must you never run an engine in a closed shed?
  3. Say the four strokes in order.
  4. Why does a two-stroke engine need oil mixed in the fuel?
  5. Who decides the correct fuel-oil ratio?
  6. How much oil is needed for 10 litres of petrol at 50:1?
  7. Name four daily checks before starting an engine.
  8. What does a black, wet spark plug tip suggest?
  9. What must you do before starting a centrifugal pump?
  10. Name one cause of a pump that does not deliver water.
  11. What must you do before clearing a tangled tiller tine?
  12. Where do you register a business name?
13

Further reading and sources

Best next reads: your engine's and pump's own manual; Level 2 of this module; the hub's Appliance and Generator Repair module (generators), Outboard Motor Repair, Motorbike and Tricycle Servicing, and Workplace Safety.

What this module does not cover: engine rebuilding, carburettor and ignition fault-finding in depth, diesel engines, chain sharpening, pump sizing and irrigation design (Levels 2 and 3), generators, outboards, motorbikes, tractors, boreholes, Ghana prices of engines, pumps and spare parts (not verified; ask local dealers), and chainsaw tree felling.

Every source used in this manual is listed, with links, in the Teacher Copy.

One application of the Cold-Start Learning Kit, which stays general-purpose and can build a guide on any topic in any field. Written in CTVET format; not an official CTVET curriculum.